I am trying to find on Cisco's web site the specification of their power cables for the ASR1002. I am particularly interested in the NEMA specification for the US power cable CAB-AC-RA .
View 2 RepliesLooking at the specs for the 3750 power supply - is the WS-C3750X-48P-S model with the 715W power supply referring to the amount for both power supplies per switch or just one power supply per switch? Meaning, is the 715 a accumulative number or, just the watts of one power supply. I would like to purchase a 3750x PoE switch with redundant power supplies. If this model is not the correct one?give me the model that offers 48 port PoE with redundant power supplies?
View 6 Replies View RelatedJust received a couple of new 4500e chassis with the 2800ACV power supplies installed. I have not seen the cables they come with standard, the plug ends are considerably thicker than normal, what is the deal, do we need an electrician to come out and rewire or purcahse new powerboards?
View 2 Replies View RelatedDoes the color strips on C3750X stack power cables mean anything, I mean the green and yellow ones. On all Cisco pictures the green one seems to be plugged in the upper ports. I asked local Cisco representative, but he seems not to be sure. We tried to try different scenarios, and it looks like it does not matter what cable end we use. We do not have any external power supply, only interconnecting C3750Xs.
View 1 Replies View RelatedSuppose I have a 3 member stack of 3750x switches. Members a, b and c.I have all 3 members stacked with all 3 *data* stacking cables in a daisy-chain topology. The 50 cm data stacking cable from switch a (on the very top) to switch c (on the very bottom) just barely reached.Of course, that means the 30 cm *power* stacking cable didn't reach between a & c. Right now, the power stacking cable goes from a to b, and then another cable from b to c. Leaving me with a useless extra 30 cm power stacking cable.
My question is, can switch "a" receive power from switch "c" through switch "b"? Is this just a big electrical "bus"? What if the power supply in switch "b" is removed?Just wondering if there is a need for me to get a longer power stacking cable (one of the 150 cm power stacking cables).
I have a customer that has a stack of 3750x switches installed in production and now would like to install the powerstack cables. The switches are in production and downtime would like to be avoided. Can you install the powerstack cables with the switches powered up? I would assume you can, but wanted to verify before doing so.
View 4 Replies View RelatedUTP cables are crossover cables or straight through??
View 5 Replies View RelatedAll of a sudden -it worked before for ages- I cannot connect with just one particular Web site via either of my two Win XP and one Win 7 machines hard wired to a common Linksys Router/hub/switch. The message is much the same either via IE or Firefox, e.g. "server not found" I tried a Ping cmd with the same result-not found.
View 4 Replies View RelatedNot long ago i was bought Cisco wap2000 access point for small business, and now the problem is to find power injector for this device. I am already tried to use AIR-PWRINJ3, but access point did't turn on.
View 7 Replies View RelatedWhen is 1130 AP going eos/eol? I have tried searching, but could just find eos/eol for 1130 power supply and not for the AP itself.
View 6 Replies View RelatedThe switch sge2000-g5 a small business switch, has a redundant power supply port built in the switch. It is a port that handles a 12v power supply. My problem is to find the exact device to supply the power to this port so I can have, obviously, a redundant power in my switch. This switch is actually out of production.
View 1 Replies View RelatedI'm just about to update flash on my router 2610, but I don't know which IOS i should take that's specification of my router: [code]
View 6 Replies View RelatedI noticed alot of question about ethernet, distances, differences, bandwidth, throuput etc of different types. I have a list off all from 10base2 all the way upto 10000baseEW, but there are so many how am I meant to remember all the differences..?
View 8 Replies View RelatedWhat the user specification with the asa5505 means.there is a 50 user and an unlimited license with the asa5505. with 50 user does this mean that only 50 user can work simultaneously over the asa, or what?
View 10 Replies View RelatedI would like to know why Cat3550 SVI's mac address is always same.for example if I configure interface vlan1 and vlan2.mac address is same as like 000d.bdfc.xxxx but Cat3750 is different, each SVI has unique mac address.
View 1 Replies View Relatedelectrical specification of cat-5e cable
View 1 Replies View RelatedSome deep technical questions regarding the AP541N access point? What I want to know is, if the AP has: - Watchdog per IP - ACK time adjusting - Site Survey.
View 1 Replies View RelatedI am trying to configure BGP on 6509 IOS. I can not specify a long interger for autonomous system: ASN: 262829 (32 bits)
View 1 Replies View RelatedI can't find any specific information on the implementation of packet inspection in a zone based policy firewall. In other words, is there a specification or even just a set of values that define the default inspection parameters for all protocols? With DPI I can manage 'some' of the inspection capabilities but I have some fairly rigorous and specific requirements to meet and I need to validate that the IOS ZBFW will meet those requirements. Specifically, I'm interested in HTTP, DNS, and ICMP but all other protocols would be useful as well.I'm working with basic routers; 871's, 2811's, 1841's, etc. The IOS in use in most cases is adventerprisek9-mz.151-3.T.
View 4 Replies View RelatedI am receiving the following error on 3750 stack switches. have already verified the power status and found ok.
IOS used: Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 12.2(55)SE3, RELEASE SOFTWARE (fc1)
211540: Jun 10 10:45:17.935 UTC: %PLATFORM_STACKPOWER-4-UNBALANCED_PS: Switch 4's power stack has unbalanced power supplies
211541: Jun 10 10:46:18.045 UTC: %PLATFORM_STACKPOWER-4-UNBALANCED_PS:
[Code]....
After stacking two 3750X switches, with four equal power-supply's, with StackWise and PowerStack , still got the next message every few hours %PLATFORM_ENV-1-FRU_PS_ACCESS: FRU Power Supply is not responding (gn4m-rt1p08-04-2)( note that the message revers to the second switch in the stack ) although the stackwise and powerstack on the switches is oke and are working correctly. !
Config : Stack-power in power-sharing mode/strict With CLI on the switch : All the power supply's and stack-power details, prio look OK.
Only: LMS prime /inventory/cisco-view/configure/power supply status result : some power supply's are marked as disabled.with the command > power supply 2 slot a off/on I manage to get the status back to "normal", but after a few hours some power supply's are again marked as "disabled".
Looks like SNMP en IOS difference from opinion.
Hardware
WS-C3750X-24S-S
C3KX-PWR-350WAC
Software
15.0(2)SE
C3750E-UNIVERSALK9-M
I keep getting alerts from our WCS stating that our 1252s are drawing low power. Now I am aware that they require enhanced PoE (up to 20W) but as we only have standard PoE in that building we purchased the 1252 series power injectors to go with them.
However, even with the correct power injectors the WCS still reports the draws low power error.
Is this a bug? Running WCS 7.0.172 at the moment.
Forgot to say we are using the PWR-INJ4 and the injector status is enabled and you see the injector MAC address when you drill in to the AP status.
We have two switches of the same model (WS-C3560-48PS-S) that are not providing PoE. I'm trying to remotely determine what the cause of the issue is.
Here is some output.
Hostname#show power inlineAvailable:0.0(w) Used:0.0(w) Remaining:0.0(w)
Interface Admin Oper Power Device Class Max (Watts)--------- ------ ---------- ------- ------------------- ----- ----Fa0/1 auto off 0.0 n/a n/a 15.4Fa0/2 auto off 0.0 n/a n/a 15.4Fa0/3 auto off 0.0 n/a n/a 15.4Fa0/4 auto off 0.0 n/a n/a 15.4Fa0/5 auto off 0.0 n/a n/a 15.4Fa0/6 auto off 0.0 n/a n/a 15.4Fa0/7 auto off 0.0 n/a n/a 15.4Fa0/8 auto off 0.0 n/a n/a 15.4Fa0/9 auto off 0.0 n/a n/a 15.4Fa0/10 auto off 0.0 n/a n/a 15.4(code)
I have a 6500 chassis with 2 power supplies. At the moment I am using the default configuration:
power-redudancy mode redundant
The problem is that an inserted module is in "power deny" state due too insufficient power.
I know, that It's not a good idea to change into combined mode (loss of redundancy), but my customers requested this anyway.
So I will change to combined mode. So here's the 1 million dollar question: "Which modules will go into power deny, if one of my power supplies fails?"
The 6500 config guide states:
"Power supply is removed withredundancy disabled
• System log and syslog messages are generated.
• System power is decreased to the power capability of one supply.
• If there is not enough power for all previously powered-up modules, some modulesare powered down and marked as power-deny in the show power oper state field."
Well, do you know if there's any way to configure some kind of priority? E.g. I definetly don't want by 10Gig Module or WiSM module to be in power deny. Can i statically make sure, those module will be powered on for sure? Like: "power enable module slot_number" How is this calculated? Or is random?
In a stand alone 3750x switch configuration, can the secondary power supply only act as a redundant power supply (active/standby), or can it become a "pool" of power similar to power sharing mode for StackPower (somewhat active/active)? I understand there is no stack involved here but I'm curious if this functionality is possible.
View 1 Replies View RelatedI am going to configure the NATing on ASR1002 and expecing to have near about 1Million nat translation. Will ASR1002 support 1million nat translations ? how many NAT translations are supportable on the ASR1002 ?I am going to configure NAT on ASR1002-5G/K9 U& have FLASR1-FWNAT-RED.
View 1 Replies View RelatedRight now I have a ASR1002 running a very old IOS version.Cisco IOS Software, IOS-XE Software (PPC_LINUX_IOSD-ADVENTERPRISEK9-M), Version 12.2(33)XNE, RELEASE SOFTWARE (fc1) asr1000rp1-ipbasek9.02.05.00.122-33.XNE.bin – 25-NOV-2009?
I am looking to upgrade to a newer version.I was wondering if there are any tricks when upgradeing this IOS. Is it as easy as loading the IOS onto the ASR and then changing the bootpath or is there an upgrade path I must follow? Also would there any need for a licence between 2.x and 3.x.
The loopback of the ASR1002 is 2.2.2.2. When I use a browser to access it, I got the authentication dialog box asking for username/password. I input the information and submit. But authentication box comes back again and ask for the username/password.
The username/password is test okay. But somehow, the web GUI just does not use it.
how can I enable an automatic power-on after a power failure on an ASA 5512-X?
View 5 Replies View RelatedIs the GLC-LH-SM SFP compatible with the ASR1002 and how does it differ from the SFP-GE-L adapter?
View 4 Replies View RelatedWe have an ASR1002 with asr1000rp1-adventerprisek9.03.05.01.S.152-1.S1.bin software.I couldn't find any documentation on how to attach an L2 interface, in my case a subinterface with a single dot1q vlan, to a BDI interface.I'm able to create a bridge-domain interface but it's down down.The command bridge-domain on the subinterface url...
View 2 Replies View RelatedI'm aware ACL's are handled in hardware on the ASR platform but wondered if there was any way to inspect how many hits we get on each line of an ACL on the ASR, I can't seem to find a command to do this.
Using LOG is not possible due to the large number of hits.
One of our customer just purchased ASR1002 router, they have three internet links from different ISPs and they dont have any remote site, they have three different public IP pool as their respective ISPs. So, is it possible to load balance the internet traffic using all three link on Cisco ASR router ( IOS - Advance Enterprise Services)
View 3 Replies View Related