I have an DLINK-dir 815 router.. I have tried for 10 hours to get broadcast IP to work, no luck.. All html/javascript modifications = no luck..The WOL works on LAN, but not over internet, so I figure it's the broadcast IP that needs to be virtual servered?
View 9 RepliesRegion : UnitedKingdom
Model : TD-W8968
Hardware Version : V1
Firmware Version : latest
ISP : french orange
I am trying to set up port forwarding on this router but it seems I need to use virtual servers but in all the guides there is a menu for this under the advance settings nat menu.I do not have that option, I have downloaded the latest firmware but still nothing.
I wonder what the difference is between the virtual server and the port forwarding because the router I was using previously had only port forwarding. When should I use virtual server instead of port forwarding?
View 1 Replies View RelatedI have DIR-601 wireless router with two computers connected: Server (192.168.1.2) and Client (192.168.1.3 on Ethernet Port and 192.168.1.4 on Wireless)
I also use dlinkddns.com and my router's public IP is mapped as abc.dlinkddns.com.
In the router Virtual Server section, it is configured as:
Public Port: 3389 (for Remote Desktop)
Private Port: 3389
IP Address: 192.168.1.2 (server's IP)
I am expecting this to allow the client to access the server via windows Remote Desktop.
The current situation is:
- When wireless is on, the client can access the server's Remote Desktop
- When wireless is off and client is connected by wired Ethernet, the client cannot connect to the server's remote desktop. After timeout, the error msg is "Remote Desktop can't connect to the remote computer for one of these reasons: ...".
- When the client is in another network, it can connect to the server through the Internet.
I am sure it's not the client's problem because it can access via wireless or remotely from another network. It's not the router's virtual server config problem for the same reasons. Will it be a bug in the router? (hardware version: B1, firmware version: 2.00NA).
I have several ports opened on my DIR-655 A3, pointing to specific ports on a NAS server i have on my network.
I've already try this:
- Reboot the router
- Erase all Virtual Server Settings and try open only one port
- Re-flash the router with latest European firmware - 1.34b05EU
I've got a DIR-825 RevB Firmware V2.06NA on a static IP wan connection routing to a SBS2008 server and 10PC's. The server is serving mail, web, and files. Router has virtual servers setup for http, https, smtp, imap, imapssl, smtpssl, pptp, remote desktop, and a few others.
Everything works fine, but the routers https forwarding stops running periodically about half an hour after reboot. The server's working fine, but it doesn't see the https request, it looks like the router is trying to serve the 443 request itself. After a router reboot everything is back to normal.
I've replaced the router with another dir-825 and it has the same issue.
Region : Others
Model : TD-W8961ND
Hardware Version : V3
Firmware Version : 3.0.0
ISP :
My router is TDW8961ND
The firmware version is 3.0.0
The hardware version is 3.0
I am trying to have a virtual http server at port 80 but when I do this and save, I get this message: "Notice: The WAN HTTP port of CPE will be chaged to 8080 if submit successfully."Then after that I cannot access the server at port 80.
Why is loop-back only working on ports forwarded in the Virtual Server section and not Port Forwarding or even DMZ? I have seen a post about loop-back on the DIR-655 from a while ago that had said to disable SPI and change NAT Endpoint to independent, I have done this and loop-back still doesn't work.
View 1 Replies View RelatedI had an old G router that had an unsecured network. It died and I replaced it with an N router and installed a secured network. I have a cable modem with wires that goes to the router. From the router, I have CAT 4 wires going to several access points around the house. Into one of these acess points, I have pluged in a wireless access point that broadcasts wirelessly---unfortunately, it is broadcasting the old unsecured network. How can I make the wireless access point broadcast the new secured N network?
View 6 Replies View RelatedWhat is the best virtual software to run on the server
View 1 Replies View RelatedSometime in the past month my virtual server has been serving slow speeds to a majority of places when I used to get 500KB/s + speeds down and 250KB/s speeds up regularly. My home network is Verizon Fios 15/5 and speedtest.net reports exactly those speeds at any test server I choose.
I've been going back and forth with my virtual server host (1and1) about my virtual server download and upload speeds. I've done a lot of testing to see if there is packet loss with WinMRT and also traceroutes from a couple locations.1and1 has done testing and verified it's NOT their network causing the slow downs as their download tests have returned fast speeds. I've tested at about 8 locations to download this file ( [URL] I can assure you that link is safe, it's just a zip of the .Net 4 redist pacakge) and 6 out of the 7 get speeds ranging from 10kb/s-50kb/s, only 1 out of the 7 gets 400kb/s+ download speeds and that is located in Chicago, 4 are from Los Angeles area and 2 from Denver area and one from Orlando area.
Is it possible to get some users (Preferably West Coast USA) here to download and report the speed it downloads, location they are at, and the internet provider and package they have? If I cannot find the cause of this, I may have to move to a different virtual server provider which takes a lot of configuration for my server because of the nature of it
I'm having trouble connecting my client/server in my virtual PC. they just aren't seeing each other when it comes to connecting them to continue my server class.
server 2003 windows xp running on virtual PC I'm running windows 7 on my computer
I have two AC1200 routers? how do i connect one ac1200 to another ac1200. Only one should act as a DHCP server and broadcast wireless; the other should be simply just a hub (vs. me having to buy a separate hub). What are the correct settings and connections?
View 1 Replies View RelatedMy D-Link DIR-655 most of the time does not broadcast wireless signal. I use Windows 7 and XP with same result. I see at least a dozen of broadcasting wireless signal in my network. Even after it worked, then next time I power-on PC, the signal is not there. The Router does not show the status light for wireless usage for these non-broadcasting time. It works and does not work.
View 2 Replies View RelatedI have an DLINK-dir 815 router.. I have tried for 10 hours to get broadcast IP to work, no luck.. All html/javascript modifications.
The WOL works on LAN, but not over internet, so I figure it's the broadcast IP that needs to be virtual servered
I have my DIR-825 (type B, .202NA FW) all set up and wireless is working well, EXCEPT for the fact that inSSIDer consistently shows it broadcasting at only 54mbps, while it also shows several of my neighbors in the 150 and 300 ranges. I'm using a DWA 160 adapter in my notebook.
I have my 2.4 channel set for g&n, and my 5.0 channel at N only. both WPA2 and AES. WMM enabled. I've tried any number of combinations but nothing seems to work.
If I was content with 54mbps, I'd have stuck with my old G router.
I'm trying to set up a load balancer within an OVH (hoster) infrastrcture, I've followed their instructions [URL] I'm using a RIPE block (5.135.193.xxx/28) and would like the first 8(5.135.193.xxx/29) to be used as the virtual server.vlan 2676 is the local one, and vlan 1227 is the public one.After all the config steps, none of these IPs are responding to a ping, nor a direct http request.
the full configuration is :
=============================================
ssh maxsessions 1
access-list ANY line 8 extended permit icmp any any
access-list ANY line 16 extended permit ip any any
probe tcp PROBE_TCP
passdetect interval 30
[code]....
I have a question regarding CSS loadbalancer. Let's say there are 2 vlans in CSS:
1. Vlan 10: 10.1.1.0/24 as external interface, interface where most of the clients are coming from.
2. Vlan 20: 10.1.2.0/24 for real server vlan.
Virtual IP 10.1.1.10 is created in CSS on behalf of two real servers (10.1.2.11 & .12) in Vlan 20. Client from Vlan 10 can http access to 10.1.1.10 successfully.
In Vlan 20 there's also few clients which need to access servers via virtual IP. Vlan 20 Client PC (10.1.2.101) can ping 10.1.1.10, but can't access 10.1.1.10 http service.
Is there any way for CSS to forward service request coming from Server vlan to be send back to the same segment?
it was possible to install RSA Authentication Manager server into the ACS 5.3 Virtual Machine ?
View 0 Replies View RelatedI have an AS-external route being redistributed into OSPF from a static route on one of my routers. I recently changed the static route from a /24 to a /26 and all of a sudden the link ID of the segment in the OSPF database went from the network address to the broadcast address: Code:
View 5 Replies View RelatedAm running firmware ver 1.00.19. Set up DDNS with DynDns.Org and all is well. Set up virtual server with DDNS info. Trying to connect to an IPcam (Foscam 8905W). IPcam is set up with static IP with ip outside Belkins DHCP range.
Problem: When trying to access the IPcam through the internet (DynDns) Belkin takes me right to the Belkin router Setup screen, not to the virtual server settings (IPcam). I was able to do it a couple of months ago,but not now. I may have upgraded my firmware in that time from 1.00.12.
I recently updated my firmware for a DIR-601 router and have internet while hardwired, but no wireless. I saved the configuration settings before updating, but this doesn't even matter because my wireless router doesn't even show up in the list of available wireless network connections. Why isn't my router showing up? I tried a few things like unplugging it and resetting it, but nothing seems to work.
View 3 Replies View RelatedWhen I create a virtual switch on hyper v, i lose network connectivity and the default gateway is missing I have to manually put the default gateway in and disable and re enable the network adaptor each time the server restarts in order to get network connectivity. I am running windows server 2012 Hyper V Virtual Ethernet Adapter loses default gateway server 2012
View 9 Replies View Relatedhow i can make my own hosting .. i own site and i need to make my own hosting?
View 7 Replies View RelatedI want to learn how to make application server?I have Windows server 2008 enterprise edition and it is connected to 10 Client Machines. I want to install software programes only on server and use them on client machines without knowing server password.
View 29 Replies View RelatedCanada
Model : TL-WDR4300
Hardware Version :
Firmware Version :
ISP : [/COLOR]
Model : TL-WDR4300
Hardware Version :
Firmware Version :
ISP : [/COLOR]
Is it possible to disable broadcasting that the WDR4300 is made by TP-Link? I want to continue to broadcast the SSID but not the manufacturer. I have looked in the various menu pages and cannot figure out how to have this happen.
I have to make a live chat (web based using ASP.NET) , like a customer service chat when the client click to start chat , the server will repsond with checking any operators that is available to chat with the client.the operator must be login to the site as active operator .how can i make the server to check the available operator ? is there a syntax or codes that can be applied in this condition?
View 2 Replies View RelatedMy problem is that i want to make an srcds server to css (counter strike source) but i cant get it online beacuse i need to port forward i got a Thomson router (or what it's called) now to the problem when i write my ip and logs in i can acces some features and some i can't acces.
View 2 Replies View RelatedI have a question that�s been bugging me and that internet searches didn�t quite explain and that is how do I make a resource available publicly e.g. web serverAll I hear so far is register a domain name but that doesn�t quite answer the full question. Id like to know exactly what happens when a user types in the url of my web site and how their traffic gets to me. Is it.. get a static ip from my isp then provide this to the domain name registrar and that it now every one can access my site?? Seems to simple.
View 1 Replies View Relatedi want to stream movies to my nexus 7 in my room only but i dont want to buy a nas. can i connect my external to a router [URL] and use that to stream movies. i dont need to be able to connect to it all over campus but mainly in my room would be nice. i read that w/o root you cant connect to adhoc with the nexus 7?
View 18 Replies View RelatedI have an old computer that is currently running XP at 2.1GHz Athlon AMD with 1.5 DDR RAM, would I be able to turn it into a dedicated server? More importantly, should I? all I have is a small home network running a couple desktops and a printer off one and connected by a wireless router to the internet, would it make a difference at all in processing speed or connectivity on any of them?
View 6 Replies View Related I have a ASA5505 in a branch connected to the head office via L2L-VPN. The clients at the inside of the ASA can use the DNS servers in the head office through the VPN tunnel. The ASA is configured to use these DNS servers, too.
dns domain-lookup outsidedns domain-lookup ADMdns domain-lookup insidedns server-group DefaultDNS name-server 172.17.6.225 name-server 172.17.6.227 domain-name some.name management-access ADM
The VPN ist connecting the networks behind interfaces inside and ADM to the network at the head office.
When the ASA is resolving a hostname it tires to use these servers. But it does via outside interface.
gw700# ping heise.deMar 30 2011 07:58:49: %ASA-6-302015: Built outbound UDP connection 35360 for outside:172.17.6.225/53 (172.17.6.225/53) to identity:117.135.114.78/2117 (117.135.114.78/2117)DNS: get global group DefaultDNS
[Code].....
One of the persons involved in a home network has installed a Dlink DIR-825 Rev-B Extreme router on the Comcast cable system to allow a 'better' wireless signal on upper floors of the home. Two others involved in the same home network use a 'secure desktop access' software called NetOp to access the network remotely. To facilitate this software, we must 'port forward' port 6502 on BOTH UDP and TCP to the single system that is accessed.
However, this setup (simple port forwarding) does not seem to work - neither does 'virtual server', for that matter. Prior to this router being installed, it was extremely simple to accomplish this remote access using a Linksys router, so our software firewall configuration has not changed but the new Dlink seems unable to allow remote access.
How (and via which of these access methods - port forwarding or virtual server) would be best? This configuration seems frustratingly difficult to accomplish and I'm about to take the Dlink 'out' of the network and re-install the Linksys with a 'high-gain' external antenna to facilitate simple signal enhancement.