My D-Link DIR-655 most of the time does not broadcast wireless signal. I use Windows 7 and XP with same result. I see at least a dozen of broadcasting wireless signal in my network. Even after it worked, then next time I power-on PC, the signal is not there. The Router does not show the status light for wireless usage for these non-broadcasting time. It works and does not work.
View 2 RepliesI recently updated my firmware for a DIR-601 router and have internet while hardwired, but no wireless. I saved the configuration settings before updating, but this doesn't even matter because my wireless router doesn't even show up in the list of available wireless network connections. Why isn't my router showing up? I tried a few things like unplugging it and resetting it, but nothing seems to work.
View 3 Replies View RelatedCanada
Model : TL-WDR4300
Hardware Version :
Firmware Version :
ISP : [/COLOR]
Model : TL-WDR4300
Hardware Version :
Firmware Version :
ISP : [/COLOR]
Is it possible to disable broadcasting that the WDR4300 is made by TP-Link? I want to continue to broadcast the SSID but not the manufacturer. I have looked in the various menu pages and cannot figure out how to have this happen.
I have an DLINK-dir 815 router.. I have tried for 10 hours to get broadcast IP to work, no luck.. All html/javascript modifications.
The WOL works on LAN, but not over internet, so I figure it's the broadcast IP that needs to be virtual servered
I have my DIR-825 (type B, .202NA FW) all set up and wireless is working well, EXCEPT for the fact that inSSIDer consistently shows it broadcasting at only 54mbps, while it also shows several of my neighbors in the 150 and 300 ranges. I'm using a DWA 160 adapter in my notebook.
I have my 2.4 channel set for g&n, and my 5.0 channel at N only. both WPA2 and AES. WMM enabled. I've tried any number of combinations but nothing seems to work.
If I was content with 54mbps, I'd have stuck with my old G router.
I have an AS-external route being redistributed into OSPF from a static route on one of my routers. I recently changed the static route from a /24 to a /26 and all of a sudden the link ID of the segment in the OSPF database went from the network address to the broadcast address: Code:
View 5 Replies View RelatedI have an DLINK-dir 815 router.. I have tried for 10 hours to get broadcast IP to work, no luck.. All html/javascript modifications = no luck..The WOL works on LAN, but not over internet, so I figure it's the broadcast IP that needs to be virtual servered?
View 9 Replies View Relatedmy wireless router isn't broadcasting. It has the normal internet up but the wireless isn't allowing us to connect at all.
View 1 Replies View RelatedI have an AP, model AIR-LAP1041N-A-K9. How does the AP work? How does the AP broadcast?. Is It a circle and the AP is the center? Does the AP broadcast more front than back? Have any blind spot? I see the datasheet [URL] -
Integrated Antenna
#• 2.4 GHz, gain 4.0 dBi, horizontal beam width 360°
I can't get it to broadcast a wireless signal?
View 2 Replies View RelatedI have problems to connect a MAC-Server from the wireless-network (WLC-4402-50-K9, Version 5.1.163). The wired clients doesn't have problems to connect to the MAC-Server. The connection works over broadcasts. The wireless-network don't forward this broadcasts. The broadcast-forwarding feature is activated. It is no problem to the MAC-server from the wireless-clients. The hole network is in the same IP-network (one broadcast-domain).
View 1 Replies View RelatedI've had a WRT54GL ( for about a week now ) with no real issues. Today my wife mentioned that the net's been flaky ( wireless nto hard wired ). I originally noticed what seemed like minutes for my desktop of laptop to connect to any web pages. Loads were extremely slow. According to the computer I had a 1 mbps connection. I did the standard resetting of the modem and router.babble babble babble. Eventually, I ran a wifi analyzer from my phone to determine an ideal channel. However, while running the frequency scanner I also noticed that my broadcasting would continue to drop off the radar for a quick moment then return. This seemed to be true no matter what channel I set. What's interesting is that the signal would read as extremely strong for 45 sec - 1 minute, then completely drop the signal, then another strong broadcast. Other neighboring signals don't exhibit this behavior....well I would see the weaker signals coming in and off the radar from time to time. I'm guessing it's some type of interference? However if that's the case I can't explain why my signal seems so strong. I'm assuming I'd see a lot of fluctuation in my signal before dropping off ( instead of going from 100 to 0 in the blink of an eye ).
View 1 Replies View RelatedI think I've been carefully through every single screen and can't figure out how to disable the wireless broadcast on my new EA6500. I typically see this in the "wireless" settings but must be missing something.
View 4 Replies View RelatedI recently had trouble connection to my Linksys WRT54G router. However, in this process I had to create a couple of new profiles/networks/SSID or whatever they are called. I now have one functioning network, but my router is still broadcasting the other two networks. How can I get my router to only broadcast the one network, I am currently using? I erased them from Vista, so that my own computer does not automatically log on to the, but that is clearly not enough. Since one of the networks is not secured with a password (dont ask why), my concern is that my neighbours can access it. BTW, I am using Windows Vista on a Toshiba Satelite A200.
View 5 Replies View RelatedI had an old G router that had an unsecured network. It died and I replaced it with an N router and installed a secured network. I have a cable modem with wires that goes to the router. From the router, I have CAT 4 wires going to several access points around the house. Into one of these acess points, I have pluged in a wireless access point that broadcasts wirelessly---unfortunately, it is broadcasting the old unsecured network. How can I make the wireless access point broadcast the new secured N network?
View 6 Replies View RelatedI just set up a brand new LinksysE4200 router at one end of my home, and a Linksys RE1000 range expander at the other end in order to provide full WiFi coverage to my entire house. Everything is working great except for one important detail.. There is currently no way to disable SSID broadcast on the RE1000 range expander! I just flashed it with the latest firmware (v1.0.01 build 2, Jul 22, 2011) , but I'm still unable to disable it, even though it is disabled on the E4200 from which it's receiving the signal it's rebroadcasting. I am seriously considering returning the RE1000. Linksys. add the ability to disable SSID broadcast on the RE1000 in a (not too distant) future firmware upgrade! As far as I'm concerend, this is a MUST HAVE feature in order for this product to even be considered for use in any sensitive network environment.
View 2 Replies View RelatedHow can you disable SSID broadcast on EA6500 wireless network.
View 4 Replies View RelatedHow do I disable the broadcast of my SSID? I do not want wireless. I only bought this router to hook up two computers to the internet via Ethernet cable.
View 9 Replies View RelatedI had a e4200,and i used 5ghz wireless.i can't set it to channel 149 or other high channel,my old wireless ethernet card can only support that.make the next version of the firmware can setting 5ghz channel to channel 149、153、157、161.
View 2 Replies View RelatedEA3500, I'm using the Smart Wi-Fi interface through a browser. How do I make my router broadcast the SSID? I think it was when I was setting up using the old interface, before updating the firmware, that I set it to *not* broadcast the network name. Now I feel like I've been all through the menus twice on the Smart Wi-Fi interface, and can't find the on/off toggle.
View 9 Replies View RelatedCan the broadcast be disabled on EA6500?
View 1 Replies View RelatedI got E4200 v.2 with the latest cloud firmware. On the previous (non-cloud) firmware there was an option to enable or disable SSID broadcast, and I disable it. Now I want to enable it back, but can not find this option in Cisco Connect Cloud. how to enable SSID broadcast on the E4200 v.2 with Cisco Connect Cloud firmware?
View 1 Replies View RelatedSome routers are able to forward to broadcast directly by sending a port to 192.168.1.255, other's I've been able to trick by forwarding to 192.168.1.254 and then editing the arp table with 192.168.1.254 <-> ff:ff:ff:ff:ff:ff. Is there any way I can edit the arp table of the E4200? Is there a way to telnet in or get a console connection?
View 9 Replies View Relatedmy question regards to a pair of WLC 4402 with 7.0.98.0 software.Actual, our security policy does not really allow any peer-to-peer communication in a wireless LAN. Therefore we set the 'P2P Blocking Action' to drop, and the 'Broadcast Forwarding' feature to disabled (default).But now there is a special requirement for two mobile endpoints to communicate with each other, because one device controls the other.To test the communication, we first disabled P2P Blocking (without success) and further enabled Broadcast Forwarding to bring the communication up. Now it works, but the configuration disagrees with our policy.
1. Is there an alternative configuration as described possible, so that we do not violate the security policy? To allow only p2p connection between the two devices, ist should also be possible to drop any else by an ACL. But how to fix the problem with the broadcast, because of the needed ARP? My idea was to use a static ARP entry, but as far as i know, one of the both devices is not able for it.
2. Because, I did not find any detailed documentation:
2a. with enabled Broadcast Forwarding, the controller forwards all broadcast for any configured SSID, right?
2b. is the broadcast limited to the source VLAN/SSID?
2c. is the broadcast limited to an AP, to an WLC, or is it broadcasted to every AP on every WLC that has the relevant SSID?
we already have two new 5508 but not in an operational state now, because we plan to implement new 3600 APs.Do these WLCs offer more/another circumstances or possibilities?
I am trying to provision three 1142 AP's so they broadcast multiple SSIDs. I have set the following commands, but I am not able to get more than one SSID to broadcast. As you can see I added the "guest-mode" command to one of the SSIDs which took it without problems. That other SSID does not accept the command.
dot11 ssid Test
vlan 2
authentication open
[Code].....
Which command in the Cisco AP1200 series will you use to broadcast the SSID using VLANs?
View 3 Replies View RelatedI have 2 cisco 1242Ag APs in one building and 7 in other building installed in my infrastructure. All these 9 APs are connected to WLC and all of them are added to default ap group to broadcast all the ssid... But 7 in the second bulding are working properly, but the 2 in the other building are not broadcasting the ssids. I checked the configuration in both APs and WLC as well... All the 9 APs are having the same configuration.
View 12 Replies View RelatedWe have a 5508 controller with about 40 LAPs, running AIR-CT5500-K9-7-2-103-0-FUS software.The need has arose to have LAPs in various locations that only broadcast specific SSIDs.
I've got seperate dyanmic interfaces already created.We have 3 "Normal" SSIDs that we broadcast to the LAPs already associated with the 5508.2 more SSIDs were created (2 different purposes).
I just can't figure out how to get it to certain LAPs to only broadcast the specific SSIDs, while the rest broadcast the normal 3, but not those 2 new ones.
I am the latest firmware of EA2700 but why I can't find there is disable broadcast SSID function?
View 1 Replies View Relatedwhy my SSID still displays even though I have the SSID Broadcast "Disabled" for 5 GHz and 2.4Ghz configurations. The name of my network shows full signal strength and a lock next to the name but I was under the impression if I have disabled the SSID broadcast it shouldn't show up at all and would force a user to manually input the network name when trying to connect to it. I have the router configured to only allow certain MAC addresses wireless access as well. Router is running Firmware Version: 1.0.03.Also, my primary computer my iMac running 10.7.2 boots up or is brought out of sleep mode I constantly need to go up to the top of my screen and re-select my network.
View 4 Replies View RelatedI have two AC1200 routers? how do i connect one ac1200 to another ac1200. Only one should act as a DHCP server and broadcast wireless; the other should be simply just a hub (vs. me having to buy a separate hub). What are the correct settings and connections?
View 1 Replies View RelatedI'm using a Cisco Wireless LAN Controller 5508, 14x Access Points 1041 and 6x Access Points 1031 in combination with a NCS 1.0.
Is it possible to broadcast SSID'S only on defined Access Points, e.g. AP 1-3,7-10,18? If yes, what have I to do?
E4200 not letting my known wireless devices connect when SSID Broadcast is turned off.
View 1 Replies View Related