Cisco Wireless :: Command In AP1200 Series - Use Broadcast Using VLANs?
Dec 20, 2012Which command in the Cisco AP1200 series will you use to broadcast the SSID using VLANs?
View 3 Replies
ADVERTISEMENT
Cisco Routers :: VLANs On SRP527w - Broadcast Traffic
Sep 22, 2011I require a system that will support 3 VLANs, the VLANs are purely for containment of broadcast traffic and needs to support inter-VLAN communication between client devices. Would the following configuration work:
Port based VLAN on the SRP527W with each port connected to layer 2 switches serving each VLAN.
DHCP server on the SRP527W assigning IP addresses for each of the V LANS in different ranges. (eg 10.10.1.xx, 10.10.2.xx, 10.10.3.xx). Would there be any benefit upgrading the Router to a SRP547W?
Broadcast A Message On Network Using Command Prompt?
Aug 10, 2011how do i broadcast a message on my network using command prompt?
View 2 Replies View RelatedCisco Switches :: SG-300 Series - Network Loop Broadcast Storm
Sep 12, 2012So the SG300's have STP on them and prevent network loops when other switches on the network also support STP too. However, if someone plugs in a non-managed switch that doesn't support STP with a network loop, is there anything within the SG300 switches to isolate and/or prevent that from happening?
(I currently have port mirroring turned on for one port and a network sniffer attached awaiting the incident to happen again).
Cisco :: Configuring Trunking And VLANs On A 2100 Series Wireless Controller?
Oct 4, 2011We have 4 1142N LAPs that I want to divide between an internal wireless and a guest wireless network using the controller. Currently all of the APs are on an established internal network, but I want to migrate one over to a test guest network before buying more LAPs to augment the networks further. Currently the port connecting to the WCS from the 3560 switch is configured as an access port using VLAN 10. Whenever I make it a trunk port carrying VLAN 10 as well as the other ports we will be using for the guest and ap-manager networks, I lose connection with the controller. To me this implies that the port on the controller is configured as an access port as well. In the documentation I found for the controller it states that by default the ports are al configured to be trunks, but it appears as though something was changed by the previous tech. All of the APs are connected to other switches, not to the controller itself.
1) How can I get the port on the controller back to being a trunk port
2) Can I use the internal DHCP server for the guest network if the subnet is different than the management subnet, or will I have to use another external server and relay/proxy it through the controller to give guest clients IP addresses?
Cisco Wireless :: Which Interface In AP1200 Will Be Used
Dec 20, 2012Which interface in Cisco AP1200 will be used if you want to use the 802.11a standard?
View 4 Replies View RelatedCisco :: AP1200 Securing Open Wireless Environment
Apr 26, 2011Need securing a wireless environment in a hotel? The SSID has to be broadcast of course but how can we protect guests from man in the middle attacks, etc.? Currently the environment is all AP1200s with no hardware upgrades in the near future. There is also a 2811 router in place but nothing else. We would love to be able to force users to authenticate with a password in order to get out to the Internet as well.
View 2 Replies View RelatedCisco WAN :: Command To Check List Of Incoming Vlans On Catalyst 4640?
Oct 4, 2011is there a cisco command to check the list of incoming vlans on a catalyst 4640 or at least that will give you the same output?we're having an issue with an ethernet circuit, links are up but ping won't go through(no ACLs) and I want to see if the vlan tag from the the other side(side B) is properly reaching side A.
View 1 Replies View RelatedCisco Switches :: Routing Between Two Vlans On An SG300 Series Switch
Oct 22, 2011I've seen lots of posts from people having problems routing traffic between two vlans with some complicated examples. Any simple step-by-step example for an SG300 switch (in layer 3 mode) to configure two vlans and sending traffic between the two vlans without an external router?
-VLAN1 10.10.10.0
-VLAN2 10.10.20.0
I've tried to do this through the GUI and can't seem to make it work. I'm missing something in the GUI.
Cisco Switching/Routing :: Internet Sharing Multiple VLANS 300 Series Small Business Switch
Apr 7, 2012My problem is that I have a Cisco 300 series small business switch with multiple VLANS each one with an IP address and two or three ports assigned to each VLAN. I have an E3200 wireless router that I want to use to use to share internet on the switch. All of the VLANs are reachable from the other VLANs and I've put a static route on the E3200 so that I can reach the VLANs from a machine connected only to the router. But I can't reach machines on the otherside of the router or get to the internet from the switch.
View 3 Replies View RelatedCisco :: AP1200 - BBSM Fails To Locate Client
Apr 25, 2005i have a bbsm server I'm bringing up on line. Trying to add the first site, i configured everything i think right, but the client gets a network error page, and the event log shows:
EventID:28
Source:BBSM_AtNotify
Description:
Failed to locate client ip:10.233.1.10 MAC: 00 00 00 00 00 db on any network device.
i did a debug on the AP1200 (12.3(4)JA) i am using and see that the bbsm is talking to the bbsm. I just can't figure out what i am doing wrong.
[code]....
Cisco Wireless :: Controller 4400 Series Work With Aironet 3600 Series
Mar 6, 2012Can Controller 4400 series work with Aironet 3600 series?
View 5 Replies View RelatedCisco Wireless :: 1140 AP Series Vs 1260 AP Series Technical Differences
Jul 24, 2012What's the main technical differences among the 1140 AP series and the 1260 AP series?I know that the 1260 supports external antennas while the 1140 supports internal antennas, but apart from that, is there any other important difference ?
View 10 Replies View RelatedCisco Firewall :: To Deploy ASA5585 In Between User Vlans And Server Vlans
Jun 1, 2012WE have to deploy ASA5585 in between User vlans & server vlans. we have to find all the ports that needs to be opened on firewall. any tools to do same.
View 2 Replies View RelatedCisco Wireless :: LAP1041N - How Does AP Broadcast
Jun 27, 2012I have an AP, model AIR-LAP1041N-A-K9. How does the AP work? How does the AP broadcast?. Is It a circle and the AP is the center? Does the AP broadcast more front than back? Have any blind spot? I see the datasheet [URL] -
Integrated Antenna
#• 2.4 GHz, gain 4.0 dBi, horizontal beam width 360°
Wireless Router Won't Broadcast?
Aug 12, 2011my wireless router isn't broadcasting. It has the normal internet up but the wireless isn't allowing us to connect at all.
View 1 Replies View RelatedD-link Wireless Does Not Broadcast?
Sep 29, 2011My D-Link DIR-655 most of the time does not broadcast wireless signal. I use Windows 7 and XP with same result. I see at least a dozen of broadcasting wireless signal in my network. Even after it worked, then next time I power-on PC, the signal is not there. The Router does not show the status light for wireless usage for these non-broadcasting time. It works and does not work.
View 2 Replies View RelatedCisco Wireless :: Broadcast Forwarding On WLC-4402-50-K9?
Sep 6, 2009I have problems to connect a MAC-Server from the wireless-network (WLC-4402-50-K9, Version 5.1.163). The wired clients doesn't have problems to connect to the MAC-Server. The connection works over broadcasts. The wireless-network don't forward this broadcasts. The broadcast-forwarding feature is activated. It is no problem to the MAC-server from the wireless-clients. The hole network is in the same IP-network (one broadcast-domain).
View 1 Replies View RelatedCisco WAN :: Can't Use Ehwic-3g-hspa-u Card In 2800 Series And 1841 Series Router
Jun 2, 2012why I can't use cisco ehwic-3g-hspa-u card in cisco 2800 series and 1841 series router?documentation said that it should work with that devices but when I installed it, it doesn't work even as device i can't see I am using cisco latest ios advance ent. 15.1(4)M4?
View 3 Replies View RelatedCisco Routers :: How Does Quality And Longevity Of SRP500 Series Compare To RV Series
May 27, 2012My Draytek 2710 just dies after 2 years so I was looking for something a little more reliable and noticed the spec of the SRP527W-U.I take it with only one antenna and reading a couple of past discussions, the wireless will only manage n-lite as some people call it i.e. 150Mbps, and not the full 300? Oh, and are the ports still only 100M and not Gig?I know the 547 would tick both these boxes but we are talking twice the price. How does the quality and logevity of the SRP500 series compare to the RV series (which would need an adsl modem) or the Linksys boxes?
View 1 Replies View RelatedCisco :: Does WLC 2500 Series Supports 1262 Series Access Point
Jun 14, 2011Does AIR-CT2504-25-K9 spupports AIR-LAP1262N-E-K9 Access Point? How can I check this?
View 1 Replies View RelatedLinksys Wrt54gv8 - Cannot Get To Broadcast A Wireless Signal
Dec 26, 2011I can't get it to broadcast a wireless signal?
View 2 Replies View RelatedCisco Wireless :: Limited P2P Communication And Broadcast Forwarding On WLC4402
Jun 6, 2012my question regards to a pair of WLC 4402 with 7.0.98.0 software.Actual, our security policy does not really allow any peer-to-peer communication in a wireless LAN. Therefore we set the 'P2P Blocking Action' to drop, and the 'Broadcast Forwarding' feature to disabled (default).But now there is a special requirement for two mobile endpoints to communicate with each other, because one device controls the other.To test the communication, we first disabled P2P Blocking (without success) and further enabled Broadcast Forwarding to bring the communication up. Now it works, but the configuration disagrees with our policy.
1. Is there an alternative configuration as described possible, so that we do not violate the security policy? To allow only p2p connection between the two devices, ist should also be possible to drop any else by an ACL. But how to fix the problem with the broadcast, because of the needed ARP? My idea was to use a static ARP entry, but as far as i know, one of the both devices is not able for it.
2. Because, I did not find any detailed documentation:
2a. with enabled Broadcast Forwarding, the controller forwards all broadcast for any configured SSID, right?
2b. is the broadcast limited to the source VLAN/SSID?
2c. is the broadcast limited to an AP, to an WLC, or is it broadcasted to every AP on every WLC that has the relevant SSID?
we already have two new 5508 but not in an operational state now, because we plan to implement new 3600 APs.Do these WLCs offer more/another circumstances or possibilities?
Cisco Wireless :: 1142 IOS Autonomous Multiple SSIDs Broadcast
Mar 26, 2012I am trying to provision three 1142 AP's so they broadcast multiple SSIDs. I have set the following commands, but I am not able to get more than one SSID to broadcast. As you can see I added the "guest-mode" command to one of the SSIDs which took it without problems. That other SSID does not accept the command.
dot11 ssid Test
vlan 2
authentication open
[Code].....
Cisco Wireless :: 1242Ag / Access Point Does Not Broadcast The Ssids From WLC
May 13, 2013I have 2 cisco 1242Ag APs in one building and 7 in other building installed in my infrastructure. All these 9 APs are connected to WLC and all of them are added to default ap group to broadcast all the ssid... But 7 in the second bulding are working properly, but the 2 in the other building are not broadcasting the ssids. I checked the configuration in both APs and WLC as well... All the 9 APs are having the same configuration.
View 12 Replies View RelatedCisco Wireless :: WLC 5508 / How To Get It To Certain LAPs To Only Broadcast Specific SSIDs
Aug 26, 2012We have a 5508 controller with about 40 LAPs, running AIR-CT5500-K9-7-2-103-0-FUS software.The need has arose to have LAPs in various locations that only broadcast specific SSIDs.
I've got seperate dyanmic interfaces already created.We have 3 "Normal" SSIDs that we broadcast to the LAPs already associated with the 5508.2 more SSIDs were created (2 different purposes).
I just can't figure out how to get it to certain LAPs to only broadcast the specific SSIDs, while the rest broadcast the normal 3, but not those 2 new ones.
D-Link DIR-601 :: Wireless Router Won't Broadcast After Updating Firmware
Nov 29, 2011I recently updated my firmware for a DIR-601 router and have internet while hardwired, but no wireless. I saved the configuration settings before updating, but this doesn't even matter because my wireless router doesn't even show up in the list of available wireless network connections. Why isn't my router showing up? I tried a few things like unplugging it and resetting it, but nothing seems to work.
View 3 Replies View RelatedLinksys Wireless Router :: WRT54GL Broadcast Keeps Cycling On And Off
Sep 22, 2011I've had a WRT54GL ( for about a week now ) with no real issues. Today my wife mentioned that the net's been flaky ( wireless nto hard wired ). I originally noticed what seemed like minutes for my desktop of laptop to connect to any web pages. Loads were extremely slow. According to the computer I had a 1 mbps connection. I did the standard resetting of the modem and router.babble babble babble. Eventually, I ran a wifi analyzer from my phone to determine an ideal channel. However, while running the frequency scanner I also noticed that my broadcasting would continue to drop off the radar for a quick moment then return. This seemed to be true no matter what channel I set. What's interesting is that the signal would read as extremely strong for 45 sec - 1 minute, then completely drop the signal, then another strong broadcast. Other neighboring signals don't exhibit this behavior....well I would see the weaker signals coming in and off the radar from time to time. I'm guessing it's some type of interference? However if that's the case I can't explain why my signal seems so strong. I'm assuming I'd see a lot of fluctuation in my signal before dropping off ( instead of going from 100 to 0 in the blink of an eye ).
View 1 Replies View RelatedLinksys Wireless Router :: How To Disable Broadcast On New EA6500
Oct 10, 2012I think I've been carefully through every single screen and can't figure out how to disable the wireless broadcast on my new EA6500. I typically see this in the "wireless" settings but must be missing something.
View 4 Replies View RelatedLinksys Wireless Router :: WRT54G - How To Broadcast Only One Network
Mar 3, 2010I recently had trouble connection to my Linksys WRT54G router. However, in this process I had to create a couple of new profiles/networks/SSID or whatever they are called. I now have one functioning network, but my router is still broadcasting the other two networks. How can I get my router to only broadcast the one network, I am currently using? I erased them from Vista, so that my own computer does not automatically log on to the, but that is clearly not enough. Since one of the networks is not secured with a password (dont ask why), my concern is that my neighbours can access it. BTW, I am using Windows Vista on a Toshiba Satelite A200.
View 5 Replies View RelatedCisco Wireless :: 5508 - Broadcast SSID Only On Defined Access Points?
Jun 13, 2012I'm using a Cisco Wireless LAN Controller 5508, 14x Access Points 1041 and 6x Access Points 1031 in combination with a NCS 1.0.
Is it possible to broadcast SSID'S only on defined Access Points, e.g. AP 1-3,7-10,18? If yes, what have I to do?
Make Wireless Access Point Broadcast New Secured N Network?
May 28, 2011I had an old G router that had an unsecured network. It died and I replaced it with an N router and installed a secured network. I have a cable modem with wires that goes to the router. From the router, I have CAT 4 wires going to several access points around the house. Into one of these acess points, I have pluged in a wireless access point that broadcasts wirelessly---unfortunately, it is broadcasting the old unsecured network. How can I make the wireless access point broadcast the new secured N network?
View 6 Replies View RelatedLinksys Wireless Router :: Disabling SSID Broadcast On RE1000?
Oct 25, 2011I just set up a brand new LinksysE4200 router at one end of my home, and a Linksys RE1000 range expander at the other end in order to provide full WiFi coverage to my entire house. Everything is working great except for one important detail.. There is currently no way to disable SSID broadcast on the RE1000 range expander! I just flashed it with the latest firmware (v1.0.01 build 2, Jul 22, 2011) , but I'm still unable to disable it, even though it is disabled on the E4200 from which it's receiving the signal it's rebroadcasting. I am seriously considering returning the RE1000. Linksys. add the ability to disable SSID broadcast on the RE1000 in a (not too distant) future firmware upgrade! As far as I'm concerend, this is a MUST HAVE feature in order for this product to even be considered for use in any sensitive network environment.
View 2 Replies View Related