Cisco Routers :: RVS4000 Is Not Renewing DHCP Lease In Auto Mode
Jan 25, 2012
my RVS4000 is not renewing DHCP lease in Auto mode. Connection lost after 24 hours.
WAN Internet interface is physically connected to cable modem - Motorola SBV6120E. Setup as DHCP server. Cisco RVS4000 is obtaining DHCP public IP without any issue, the problem is that the connection drop every 24 hours and I need to release/renew DHCP each day to be able to communicate after 24 hours. After I loose connection I need to release DHCP, the WAN interface goes down and I need to renew DHCP then. I receive the same IP address and connection is againg UP and working.
tried to load new firmware and also setup the router with default configuration, but without any change. as there is no auto-reboot function, it is really annoying to log into managment interface each day. I also loose remote access after 24 hours, so I am not able to access the rotuer from outside. My local provider do not support static public IP on WAN, therefore I have to use DHCP.
Is there a way on the security appliance SA520 to remove someone from the DHCP lease client manually rather than setting the DHCP lease time to expire in less time like 4 hours or 2 hours. I was able to do this on other routers by highlighting the connected device and click remove. If not any recommendations on how to handle the device that are attached via DHCP and the person is no longer here, but the lease time is not up. I have set DHCP lease time to 4 hours.
I've been running a cisco asa 5505 for quite some time and it has been running fine, now all of a sudden it starts to renew it's outside dhcp adress like every 2 hours. I dont think it's the ISP since I have another device connected also using dhcp to the same ISP and it doesnt renew itself, it's just the ASA. Rebooting it, makes it pick up an adress straight away. The interface seems to be up, the GUI just reports "no ip adress" and then the ASA get's a new IP after about 10-15 min without one. Pressing the renew IP adress button in the GUI throws an error.
Today I installed the 1.0.2.6 Firmware on a RV180W. I only have now two problems regarding the Static DHCP support in the GUI.
1. Via the Networking > LAN (Local Network) > Static DHCP I have no buttons to Add a new static Lease. 2. Via the Networking > LAN (Local Network) > DHCP Lease Clients I can thick a Lease and click on Make Static IP. The result is an error: Operation failed.
I just tried replacing a cheap domestic router/switch with an RVS4000 V2 on our work network. This has a WAN connection to a cable modem for internet access via a dynamic IP address.
When I first connected the RVS4000 it got a WAN ip address via DHCP of 192.168.100.11. This is the type of IP address we get when there is an upstream problem with our ISPs cable network, and sure enough we had no internet access. The RVS4000 was set to use DHCP on the WAN interface. So I logged a support call with our ISP but they said there were no problems at their end.
I then swapped the RVS4000 out for the original router. This worked fine and got a WAN DHCP address of 77.xxx.yyy.zzz as it should. Swapped back to the RVS4000 and back to the same problem of getting a 192.168... address.
So, I downloaded the latest firmware from Cisco, which was V2.0.3.2 and flashed the RVS4000.
I then tried again connecting the RVS4000 to the cable modem but this time it would not get any WAN DHCP address at all. On the Status/Gateway page of the web interface it said that the WAN interface was down. However, on the front panel there was a yellow light indicating a live connection on the internet port.
I'm trying to connect my WAG160N as a ADSL modem (disable the router function) and connect a real router (RVS4000)So, i put my WAG160N on birdged mode only, disable the DHCP on my RVS4000, i did configure my PPPOE access (user and password), change the IP adress 192.168.0.2.configure the DHCP and try to connect. i tryed to connect the RVS4000 and the WAG160N either with cross cable or a direct cable. I can get access to the RVS4000 192.168.0.2 and get access to the configuration menu but cannot get access to my WAG160N 192.168.0.1 even a simple ping.when i try to test the connection on my RVS4000 (status) it seems that my connection is up but i cannot get access to internet.
Started this morning woke up checked my phone no wifi hmm weird checked my hp tpuchsmart connected but jo internet access checked my router(netgear wireless N 300) made sure my modem and all wires are connectedNext went to my router ip 192.168.1.1 after reading some forrums i thought maybe if i changed the ip or sum i would have worked i know dumb though.. any way i believe i disabled my dhcp.. and one of the ip ad on the same page to 192.168.1.3 thats when it got worst i tried ipconfig/release saysNo operation can be performed on bluetooth network connection 2 while it has media disconnected.No operation can be performed on local area connection while it has its media disconnected(Its a wireless connection from my touchsmart to my router) I have tried goin back to the routers page but i can no longer find itI have also tried ipconfig/renew but i get this...No operation can be performed on bluetooth network connection 2 while it has its media disconnectdAn error occured while renewing interface wireless network connection : unable to contact your dhcp server. Request has timed out.No opration can be performed on local area connection while it has its media disconnected
delete a lease from a DHCP scope on a WLC 5508? I'm using that unit as the dhcp server, no relay. I am unable to find anything either through the web or cli.
my Laptop is about nine years old, HP Pavillion Pentium 4. I run Windows XP Home Edition Version 2002 SP3. I use a broadband card from Verizon that I just put in my USB (no router, etc) I'm getting a System Error Source DHCP Event ID 1002. When this happens, my computer, I believe, is going into sleep mode and I have to reboot the system. When I turn it back on and go back on the internet, all my websites that I was in are still there. The error says: The IP address lease 10.170.223.48 for the Network Card with Network address 2c3068c16ED1 has been denied by the DHCP Server 10.173.229.86 (The DHCP Server sent a DHCPNACK message)The DHCP Server Service did not extend the lease on your computer's IP address, so your computer temporarily lost its connection with the Network. I tried the ipconfig /release and ipconfig /renew. I tried going in services.msc and going under DHCP and keeping it automatic but stopping it. I called Verizon and I believe he refreshed my Network settings (I think I knew more about the topic than he did) He said it was my computer, whatever. I just tried the static IP but it didn't seem to take. I restarted and it jumped back to automatic. My last guess is it's something to do with the time frame of when it automatically obtains the address and when it expires. When I do the ipconfig /all it shows only a two hour time frame before it expires. Today I noticed that my computer shut down/sleepmode at the exact time the ipaddress was obtained. So, is there a way to increase this time between obtaining and expiring?
I've been having this issue for about 3 months now, off and on, never seemed to be predictable but started happening more and more, which prompted me to look into it.
Currently, the DSL Modem is configured in bridge mode with the ASA handling PPPoE. The WAN address is being assigned via DHCP. The ASA is running 8.2(1). The WAN interface will drop it's DHCP lease and will not renew it without power cycling the DSL modem. I did a little bit of googling and found mention of setting "dhcp-client client-id interface outside", specifically this was an issue pre 7.2(22), but doesn't seem to affect my situation. Originally, I had the MTU on the outside interface configured as 1500, changing it to 1492 has not resolved my issue either.
I've enabled PPPoE and DHCPC debugging and posted the results below when the event occurs, I'm thinking this is moreso a PPPoE issue than it is a DHCP/DHCP Lease issue as I am not seeing any debug messages from DHCPC.
I have several Cisco WAP4410N access points. They are configured to automatically obtain an IP address through DHCP. This works fine, but I've discovered when the DHCP lease expires, the access point doesn't renew it. It continues to use the same IP address but does not renew the lease. If I reboot the access point, it will renew the lease again.Is this a known issue with the WAP4410N? Is there any way to work around this, other than setting a static IP address or rebooting regularly?
I have a remote site on a 2811 IOS 12.4(15). Interface FA 0/0 faces the ISP and is set for DHCP. What command can I run to see all of the information given out with the IP lease from the ISP? I need to find out what the IP address of the DNS servers are.
Im facing with some DHCP lease issue and its like this,Our Cisco 2951 edge router is configured with local dhcp pool for a set of remote users when they connect through Cisco VPN which was working fine until we planned to change it to a Windows box that is configured for DHCP.The basic idea now is to relay the DHCP requests that are coming from the remote clients through Cisco VPN to the DHCP Windows server. So we added the scope on the server and changed the client config on the router as follows (highlighted is the dhcp relay config). [code]
I'm setting up a Cisco Aironet 1141 (standalone mode, AP) to handle wireless traffic in the office. It gives out 2 mbssids, one of which authenticates domain users through a RADIUS server and places them in an appropriate VLAN (RADIUS options 64, 65, and 81). The other is a guest ssid that uses WPA-PSK and places users in the restricted guest VLAN. Physically, the AP is connected to a 3750 PoE Catalyst, to which RADIUS and DHCP servers are also connected. AP, SSIDs, RADIUS and EAP authentication all work. The configuration given below is a working configuration. People do get authenticated and do get placed in the appropriate vlan. The problem is that, once authenticated, the "Obtaining IP Address" phase on the client hangs and most clients timeout without getting an IP address. Given that the DHCP server is on the same switch and a test simple ASUS Wi-Fi IP gives out the same scenario (except the multiple VLAN) at the speed of light, I don't think that it's a problem with the network connections between clients and the DHCP server. After reading some topics here, I realized that probably other communication will be extremely slow, as well, but haven't tested that for sure. Clients are all non-Cisco - smartphones, notebooks, etc. Most of them are 802.11G, not N.
a couple days ago my BEFSR41 started making trouble, and so far I have not been able to get it working properly again. When I hook up my laptop directly to the cable modem everything works fine, and I get an IP address via DHCP. When I connect through the router, though, the router status shows 0.0.0.0 for all DNS, gateway, etc. addresses, and even pressing DHCP Release/Renew doesn't change that.Also, in the log I see these messages:
2012-08-08 20:30:41 warning DHCP RENEW WARNING - Field invalid in response 2012-08-08 08:30:52 notice TLV-11 - unrecognized OID
Since I can connect to the cable modem directly, it seems the cable modem is not at fault.My overall setup is:
- BEFCMU10 cable modem - BEFSR41 (not sure which version, but I believe it's a 4.x) - WAP54G
Could it be that my provider (Cox Communications) has changed some configuration in their DHCP server, and my laptop (MacBook Pro) can handle it, but the router cannot?
i cant seem to change my dhcp lease time even though i change my Client Lease Time to 1 day. Firmware Version:v1.0.06 build 001 Apr 29 2011 11:08:40Boot Code Version:v0.03Firmware Verification:Current Time:Sun, 25 Sep 2011 10:15:32 PMInternet MAC Address:Host Name: Domain Name:
I just bought an e4200. I was using a LinkSys WRT54GS running DD-WRT alternative firmware.
One feature that I really liked in DD-WRT was the ability to assign static IP leases from the DHCP server. I liked having all of my devices running with a predictable, known IP address on my network. I have a Home Theater PC, and various controller applications that run on iPhones, etc. - some pretty homebrewed. Configuring the firewalls, etc. was much easier with IP address based controls.
Is there a way to achieve the same within the e4200's stock firmware?
I own a Nanostation5 Loco, and I have a router behind it.I would like to add a DHCP Lease to that router and do a port forward to the router.I can not find the DHCP Lease option in Nanostation settings, but if I choose to see DHCP Leases in "Extra info" on main page I can see some MAC and IP addresses there.When it comes to port forwarding, I fill the form slots with info, and when I press OK to save it a pop-up comes saying "Please fill out this field", a field for another forward rule.
we finally got my Cisco refurbished E2500 configured and working downstream from a UVerse 3801HGV box. We had to change the default IP address of the 3801 because it conflicted with the E2500's default. The E2500 is set up to get its Internet IP address using DHCP from the 3801. This is working fine for normal web browsing, etc. However, anything that requires extended connections (downloads, streaming, etc) freezes after a couple of minutes, forcing me to refresh the action to get it started again. Extremely annoying to say the least.
I'm pretty sure that I've tracked it down to the E2500's configuration of the 3801's DHCP allocation. For some reason, the E2500 wants to set the DHCP Lease Time for the 3801's assigned IP address to 10 minutes regardless of the upstream settings from the 3801. The 3801's default is 24 Hours which I've changed to 168Hours (7 days), but the E2500 stays stuck at 10 Minutes. Specifically, I'm referring to the setting displayed on the E2500 under Status>Router>Internet Connection IPV4>DHCP Lease Time.
On the BEFSR41 v1 series and WRT54G series, what is the maximum value for the DHCP "Client Lease Time (in minutes)?" It seems that 2^16 -1 (65535) minutes is the max. This is about 45 days. has the max value changed with newer versions of these devices?
I have a Linksys WRT310N v1 with firmware v1.0.10 build 002Jul 19, 2010 My router fails to renew it's DHCP lease from my cable provider, causing internet access to drop. I can still access my cable modem at 192.168.100.1, but I must do a "IP Address Release" then "IP Address Renew" to get back internet access. The router works fine otherwise.
I'm trying to change the DHCP Client Lease Time from 1440 minutes to 480 minutes. When I try to apply the new settings, I'm getting a message that says "Invalid Characters" and it won't stick. I've tried this in three different up-to-date browsers (ie10, Chrome and Firefox). Also, I'm connecting locally through LAN and I have the latest EA6500 Firmware: 2.1.39.145204
I am trying to sort out an IP problem on my mates PC. I have setup a Linksys wireless router on his home broadband and it works fine with my laptop and gives me a DHCP address. When I try to connect his home PC either with a wireless dongle or ethernet connect it gets a Public IP address through the router and not one of the DHCP addresses. Even if you give it a static IP address and setup the router to accept it when you turn the PC on it still gets this public IP address. It is associating with the wireless router but only gives a local connection. I have done the ipconfig and it just renews the public IP address to a different one
i have a adsl modem that is sending dhcp reqeust and i want to use that on my cisco switchs 3560 48 ports.i want to use the interface port 0/48 as a WAN connection and i want to use the other interfaceports for DCHP pool.i have an d-link (dir655) router at home and i want to have the same situation on my cisco switch my WAN interface get from a DHCP reqeust an ip adress from the provider like 10.10.123.44 (for the cisco switch would this interface port gig 0/48)then i want to configere my LAN as a DHCP pool like 192.168.0.1 (for the cisco switch would this interface port gig 0/1 - 47 .
how to straight away enter priv EXEC mode when authenticated for asr1002?? Using XR12000, it can be done but asr1002 have to input enable passwd...my username for asr1002 have privilege 15 and i want to enter priv EXEC mode straight away after login without asking the enable passwd.
We are facing to an annoying issue. We have a 6509 running in Catos 8.3(4) with WS-X6548-GE-TX, WS-X6348-RJ-45 and WS-X6148-RJ-45. When we configure the mode in auto negotiation, it comes up in half duplex. We need to configure the speed mode at 100Mbit/Full to make it work. But if the chassis or port restarts (not the server), the link becomes half duplex. This happens only on module in Gigabyte like WS-X6548-GE-TX.
Cable have been replaced but does not work. It is not happened on another chassis running on IOS 12.2(18)SXF17b with WS-X6548-GE-TX.
I just got a new RV042. V3 Hw.For setup and testing before putting it in action, I've attached the WAN1 side to my internal network.But it fails to get an IP address, and the log shows: "Infinite lease time, exiting".My current router on the LAN is giving out DHCP addresses with 3 hour lease time, and I've checked with the PC's on the LAN that this is correct.The routers DHCP status shows that the lease time for the RV042 is 3 hours ahead.So why does the RV042 complain about long lease time ?Is there a way to avoid this error from occurring?
I have tried to change from 'Gateway' to 'Router', but this does not change anything.Also tried a factory reset, with no luck.Fw is upgraded to the latest 4.0.4.02
I have RV042 and E4200 routers . I tried the manual UPnP port forwarding using Rv042 router and was succesful ( by typing 192.168.1.1 in the explorer and logged in using user name and password )
I am using a linux embedded system whose Internal IP ,Internal port are mapped .This system is connected to one of the LAN ports
I want to try auto UPnP port forwarding both for RV042 router and Linksys E4200 routers
After enabling the Upnp option only and logging out ,Can i add a port mapping entry in this router without logging in using a C++ program which runs on linux embedded system .
I have an RVS4000 located at my office. A user of mine also has one at their house. We have created an IPSec Tunnel between the 2 of them and have them successfully communicating between the 2 networks with no problem.
The problem I have is if I make a change on their end and the router needs to reboot to apply the changes, the WAN port never renews it's DHCP address. The end user must unplug the unit, plug it back in and then the system comes back up with the correct WAN DHCP address, and the tunnel is connected automatically.
I beleive they have the newest firmware (2.0.0.3) but I cannot confirm that right now as the unit is down. I bought the 2 of them at the same time - my unit at the office has the 2.0.0.3 firmware so I am assuming the users does as well.
