i have 4507R with dual supervisors (WS-X4013+10GE) with IOS cat4500-ipbasek9-mz.122-46.SG.bin the supervisor module are in 3 and 4, and I want to connection port 5, but i have interface and line protocol down "inactive" error.
So I realized to use command "hw-module" to change the module to GE port. However, I am not able to use the command as" I cannot use the command "hw-module uplink" as well.
Can we put a module on a 4507R switch running on a live production? The module will come from a 4506 switch.
View 8 Replies View RelatedMy Company use Core Sw 4507R-Sup 7L-E with Enterprise Services License. I has upgraded to use iOS cat4500e-universal.SPA.03.03.01.SG.151-1.SG1.bin
When I use match protocol in class-map, there are only about 10 protocols, and not have those ones I need. I intend to expand the list of protocols to do some Policy-map by loading PDLM. But 4507 is no longer support NBAR. So do we have another way to set Catalyst 4507R with Sup 7L-E recongnize more protocols in match protocol command?
Is there some kind of trick to getting the fastethernet 0 management port to come up? My adjacent switch is up/up, but fe0 is down/down. I dont' see how this could be possible. I am getting all my info remotely, but I am pretty sure it's wired up correctly.
View 2 Replies View RelatedI read quite a few documents on configuring SPAN on a cisco switch but none of them mention any limitations or any kind of CPU load it can have on a switch. I need to configure this on one of our switches and would like to know if there are any implications related to SPAN.
View 5 Replies View RelatedI have a server with 4 ethernet ports, 1G, they are bonded together, two of them was pluged into cat6500 module WS-X6724-TX. now we have moved the two ports to the replace module WS-X6748-GE-TX.
I have checked server side, the bond configuration are same no changed. what is possible reason replace module will cause link offline? why "sh run all" give the port is shutdown?
I have Cisco 800 series (888w) with BRI-ISDN port. Is there any way to change the usage of ISDN port to normal RJ45 port?I want to use this SOHO router to sharing connection.
View 0 Replies View Relatedi just want to ask whether i should do some configurations or not on my cisco switch 4500 L3 regarding the error of 500 invalid port command when host try to access FTP active on to FTP server, i just did static route on gig interface with no switchport mode to that host network, all traffic type was allowed except the FTP with active mode?
View 7 Replies View RelatedI've got a pair of N7010's in a vPC domain with some FEX's attach running NX-OS 6.0.2. I am experiencing port failures on my N7K-M132XP-12L module the port got shut down due to internal errors with Error Disabled status and I am not able to bring the port back up. I am getting the following errors when I try to reset it. I am hoping is not hardware related as my vPC peer-link is on this module and I only have a single N7K-M1 32 XP-12L in each N7010. Replacing the module will be painful. [code]
View 7 Replies View RelatedMy questions is can a 4 port PoE switch module (EHWIC-4ESG-P) and a 8 port switch module (EHWIC-D-8ESG) be used at the same time in a Cisco 1941 router?
View 1 Replies View RelatedI have a laptop with a single physical NIC which I have used the advanced management tools to create two virtual NICs (say vlan 10 and vlan 20) and both are on the same subnet (say 192.168.4.x). One NIC is for normal TCP/IP traffic and one is for broadcast/multicast traffic (I have some custom software that requires this to be the case and works fine on an older laptops with built-in physical NIC and PCMCIA XIRCOM NIC). The dual NIC laptop communicates with a dual NIC server via a Cisco 2811 router (which has a 16 port switch module at the back) and has vlans set up so.
What I want is for the single NIC laptop (with two virtual NICs) to be able to also communicate with the server. Basically, one NIC is for normal traffic and one is for multicast/broadcast traffic. All three machines need to be able to talk to each other using the NIC for normal traffic and both laptops must be able to receive broadcasts from the server. What is the best way to configure the router to handle the trunking/tagging? Most configuration documentation I read has two complete subnets for the two virtual NICs. Note that all three machines use static IPs and are part of a workgroup so no DNS and domain servers etc.
We have recently purchased a Cisco 4506 that has several Gigabit Ethernet modules installed.One of the Ethernet Gigabit modules - a WS-X4424-GB-RJ45 - is being picky with who it talks to at Gigabit Ethernet.
If I plug a laptop into one of it's RJ45 ports using a Cat 6 cable, nothing happens. No link light, no notification of link up or down on port statistics, absolutely nothing.If I plug a server into the same port it works fine at Gigabit Ethernet (even using the same Cat 6 cable).I can get the module to recognize a laptop if I fix the speed/duplex on the laptop to 100Mb/Full. I have tried this with other staff laptops from different vendors (HP / Dell / etc.) all with the same result.
The module directly underneath this module - a WS-X4448-GB-RJ45 - works fine for both laptops and servers. We have tried swapping the module positions but to no avail.
I am looking to find a command or counter to tell me if a cisco switch port on a 4510 was ever up and passed traffic. I want to shutdown all unused switchports on our access switches. But before I do that I need to make sure device is just not off or the person is away on vacation. If I do sh int interface, is there a counter I can reference.
View 4 Replies View RelatedWe have two 6509 switches with one WS-X6704-10GE module in each of them. There is an optical cable between the two switches plugged in WS-X6704-10GE module on both sides. When you shut down the port on one side the other port still stays as up and you need phisycally to unplug the cable to have it down. The same behaviour is seen no matter on which of the two switches you shut down the port, the opposite one always stays as up and only removal of the cable makes it go down.
The ports are configured quite simply:
interface TenGigabitEthernet1/1
switchport
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1-10
no ip address
udld port
The IOS version is 12.2(18)SXF8
I have a 3925 Router with a 48 port switch module (part number SM-D-ES3G-48-P). I have no problem accessing the 3925 Router, but when I go into the 48 port, I get an error that reads
Error Hardware not supported by firmware. Try loading a newer software instead. System Resetting...
I know that the wrong IOS is installed on the switch, but the problem is that this is an endless loop. The switch resets then comes back to the same error. How to get the switch out of this loop so that I can load the correct IOS.
I have a 6500 switch and i recently removed a module (line card) from the switch. The problem is that the port configurations of the removed module still exhists in running configuration. I was not aware of the right procedure,[URL] however, i would like to know whether it resolves if i reboot the switch.
View 1 Replies View RelatedI have a 1941 that I am going to deploy with a HWIC-D-9ESW switch module (I only need 3 switch ports but need the PoE). I am going to hang a 1262 autonomous AP off one of the ports but I need to configure MAC address port-security so that only that AP can pass traffic. I know the switch modules are 'almost' exactly like a switch for commands but I can't seem to enable or configure any port-security settings. Is port-security no available on the switch modules?
View 3 Replies View RelatedWe have a core switch with the following ios and supervisor engine. Can we add a16 port LR (x2)or LRM(X2) ON the core switch?if not what modifications has to be done?if an ios upgrade is necessary is it a costly affair?At present we have two 1gb up link modules in single and multimode fiber .
#sh moduleMod Ports Card Type Model Serial No.--- ----- -------------------------------------- ------------------ ----------- 1 16 SFM-capable 16 port 1000mb GBIC WS-X6516A-GBIC SAL0803T308 2 48 SFM-capable 48 port 10/100/1000mb RJ45 WS-X6548-GE-TX SAD07500600 5 5 Supervisor Engine 720 10GE (Active) VS-S720-10G SAL1439UMZK
#sh versionCisco IOS Software, s72033_rp Software (s72033_rp-IPBASE-M), Version 12.2(33)SXI4a, RELEASE SOFTWARE (fc2)Technical Support: [URL] Copyright (c) 1986-2010 by Cisco Systems, Inc.Compiled Fri 16-Jul-10 19:51 by prod_rel_team
ROM: System Bootstrap, Version 12.2(17r)SX7, RELEASE SOFTWARE (fc1) uptime is 1 year, 27 weeks, 4 days, 23 hours, 30 minutesUptime for this control processor is 1 year, 27 weeks, 4 days, 22 hours, 58 minutes(code)
Im trying to follow along documentation i see via train single videos and some online resources. I am trying to enable port security.I have a Catalyst 3546 XL when i type in "rtr1# switchport ?""port-security" is not only of the options to choose from. I have already set this as an access port.
View 4 Replies View Relateda switch port is shutdown, but when i use NO SHUTDOWN command it is working and shows administratively down. like this command does not affect on it. i should enable this port? what can i do btw, port is not in errdisable and portfast is enabled.
View 3 Replies View RelatedAny way to test in a lab what would happen if a tech mistakingly added "switchport voice vlan XX" to a trunk port? I am try to do some RCA on an issue and this has been identified as a possible cause by one of my techs.
The config is Switch1------Switch2--------Switch3 Each interswitch connection is configured as a dot1q trunk with all vlans allowed. The link between switch2 and 3 is where switchport voice vlan 10 was added. Switch1 is a 3750 and 2/3 are 3560's.
show cdp neighbors command shows two devices connected through the same local port?I have a Cisco 3560 that when I issue the "show cdp neighbors" command I get the following results: [code]
the question is why is this showing that Gig0/3 is being used twice to connect to two different devices. I have verified there is no hub connected to this port and in fact Switch3 is not connected to Switch1 at all yet it still shows up in the CDP table.
I have cleared the CDP table on every device at this location and still get the same results.
I have configured a SVI in my 4500 ( Sup 7-E 10GE,,,,,,and,,,,,cat4500e-universalk9.SPA.03.02.00.SG.150-2.SG.bin) switch and it is showing Down Down, because there were no active switch port in the vlan, I added one switch port to this vlan but this port also in the down state, so i added the SWITCH PORT AUTO STATE EXCLUDE command under this port, even after this also the SVI never came up, So i added one systen to the port so both the switch port and the SVI came up...So why SWITCH PORT AUTO STATE EXCLUDE command have no effect in this model of the switch..
View 4 Replies View RelatedOn a 3750 you can do a show platform port-asic stats drop command. Is there a corresponding command for 6500 chassis?
View 7 Replies View RelatedCan you configure a Cisco 1941 to use an 8 port EHWic module and the 2 onboard GE ports in a single LAN?
I've discovered you can't have the on GE ports associated with a VLan, and I'm when I've previously researched for a solution, bridging was mentioned but I cannot seem to get it to work (or completely understand it)The reason I would like to use all 10 ports on for the LAN is becuase I have 10 devices I need to connect to the 1941?
Is there any way to change the port that is used for syslog messages on a Cisco 9500 switch?By default this is set to UDP port 514.There doesn't seem to be a command to change the port.
View 1 Replies View RelatedI am experiencing 1 4548 module fail issue with one of my customer place. unfortunately they are having only 1 4507R+E chassis and 1 4548 module. however i have replaced the module 4548 and getting the same error even after replacing ...!! but they are having redudant X45-SUP6L-E tried by removing each at one time with no luck. [code]
View 3 Replies View RelatedI have several closets with Cisco 3560 on the edge that I'd like to change the vlan that's used for the management vlan on each. In the core I have a Cisco 6509 with Sup720's.
I'd like to do this by changing the native vlan on the trunk port on the core 6509 interface that connects to the 3560. and leave the management vlan on the 3560 as vlan 1.
Seems trivial but what I tried didn't work and I didn't have the window to troubleshoot. I'll paste the simplified configs for the interfaces below
!
6509 configs:
!
interface Vlan50ip address 172.16.50.2 255.255.255.0!interface FastEthernet
[Code]....
I'm trying to change a vlan on a port-channel but I am getting this error when I apply the change:" error: command is not mutually exclusive",I have done this in the past but I cannot remember exactly what I should type to apply the change.
View 2 Replies View RelatedI'm in the middle of a Nexus 5000 project and recognized today while configuring port-channels, that some of the interface numbers are reserved for internal use.
Is it possible to change or configure which port-channel interface numbers are allocated for internal use by NX-OS?
Unfortunatly I wasn't able to find a solution for this issue in the offical Nexus documentation, the search function of this forum or Google. If I did miss something or didn't look careful enough at the Nexus docs, I'm also happy with RTFM (... fine manual) responses and links to the info :-)
Additional info:
Nexus5k(config)# interface port-channel 128 ignored port-channel128: internally used, configuration not allowed
Port-Channels 111, 113, 115, 119, 121, 200, 211, 222 were created manually, but 127 - 129 were not.
Nexus5k# show port-channel usage
Total 11 port-channel numbers used
============================================
Used : 111 , 113 , 115 , 119 , 121 , 127 - 129 , 200 , 211 , 222
Unused: 1 - 110 , 112 , 114 , 116 - 118 , 120 , 122 - 126 , 130 - 199
201 - 210 , 212 - 221 , 223 - 4096
[Code]......
I have 2 x 3750 stacked, the port number of the master switch is gigabitEthernet2/0/1, slave as gigabigEtherent1/0/1.
Can I change the port numbering so that the master switch gets GigabitEthernet1/0/x?
what is the use of no switch port command in L3 switch?
View 7 Replies View RelatedWe have a new 4507R-E Switch which RME keeps reporting as "CONFIG_CHANGE" each evening. When you click to see the change, the only thing that has changes is the "ntp clock-period".
However, we have configured "ntp clock-period" as an exclude command in RME Config Managment.
