We have a new 4507R-E Switch which RME keeps reporting as "CONFIG_CHANGE" each evening. When you click to see the change, the only thing that has changes is the "ntp clock-period".
However, we have configured "ntp clock-period" as an exclude command in RME Config Managment.
Need to confirm on 4507 R switch should i set config reg to 0x2102 or 0x2101?
View 4 Replies View RelatedI need to understand why change audit report reports an unused username Name of the user who performed the change. This is the name entered when the user logged in. It can be the name under which the LMS application is running, or the name using which the change was performed on the device. #The User Name field may not always reflect the user name. The User Name is reflected only when: A config change was performed using LMS. #A config change was performed outside of LMS, but the network has username-based AAA security model, wherein authentication is performed by an AAA server, which could be TACACS/RADIUS or local.
View 2 Replies View RelatedCurrently, my report links are displaying the server as "lms" instead of "lms.domain.net". Where do I change this within LMS?
View 2 Replies View RelatedMy cisco works LMS3.2 is not showing recent configuration of my Cisco devices. also it dont show any change report on last 24 hours or even if i select x number of day, looks like its not saving any changes made on devices.
today i logged in and cisco ASA was showing this in status as well Configuration Last Archived Time May 03 2012 11:27:46 EDT on checking i could see it is same date when cisco ASA was added in cisco works. do i need to click some where for auto update configuration changes and latest confoguration in cisco works setting?
i have 4507R with dual supervisors (WS-X4013+10GE) with IOS cat4500-ipbasek9-mz.122-46.SG.bin the supervisor module are in 3 and 4, and I want to connection port 5, but i have interface and line protocol down "inactive" error.
So I realized to use command "hw-module" to change the module to GE port. However, I am not able to use the command as" I cannot use the command "hw-module uplink" as well.
I have about 1400 devices in LMS for this one customer.
They have 1200+ IOS devices
200 + catos devices
My problem is we use 2 differnt change scripts in Config Editor for IOS and CATOS. I have a list of all of the IOS and CATOS devises in txt format.
Is there some magical way to just upload the txt files into Cisco works instead of searching for them during the Config Editor batch job creator? I find it takes hours to sort this batch job out
want to be able to change LAN IPs on the fly for telneting into different equipment
View 1 Replies View RelatedI was changing some settings on the router, disabled the WMM QoS, and I can no longer see either the 2.4 or 5GHz networks. I power cycled, tried resetting to defaults but the wireless seems to be dead. I can manage it wired, but that does me no good.
View 2 Replies View RelatedIf i connected the latop to brand new out of the box ASA 5505 through consloe cable and i have a config file on this laptop from other ASA5505, is there anyway i can upload that config file into startup-config of this new ASA5505 through console cable, without using TFTP or FTP?
View 5 Replies View RelatedI have a Cisco 2811 router and when I turn of the router the running config is lost. I have to the following to get the router running of the start-up config settings.
router#copy start-up running-config
I'm new to CiscoWorks and I inherited the system in my new job. We are running LMS 3.2 and I want to run a report to see what versions of IOS that are running on the network.
View 3 Replies View RelatedUnable to run Eos/EoL report, I get error that my cisco.com credential are not valid, I verified my credential and they work fine. I'm running RME4.3.2 on Solaris 10.
View 3 Replies View RelatedI have cisco acs 5.3 appliance. Issue is, when i view tacacs accounting it only shows 100 pages of records. So first kindly tell me if this is the limitation of acs 5.3 to only show 100 pages. Secondly if i want to export the report of last 30 days, its also not showing the last 30 days.
How to get the report of last 30 days
I have an issue with rme 4.2 from LMS 3.1 When I try to generate a syslog report this shows me nothing. I locate SyslogCollector.log file and I see sometnig wrong.
View 4 Replies View RelatedIs it possible to run an uptime report using CWLMS 3.2 ?
View 2 Replies View RelatedI am using LMS version 3.2 and i am not able to generate EOS/EOL report with error no connection to Cisco.Saw an update i LMS portal as this:
Now Available! LMS 3.2:Patch for un-interrupted service of Cisco.com download for Device/Software/PSIRT/EOX updates (To be applied on or before 15-June-2011)
so upgraded the patch cwcs33x-win-CSCto46927-0.zip and restarted the demeon as read in the read me file for the patch.Now the job execution status is always shows running, its neither fail nor pass.
My customer recently deployed WLCs and WCS in their environment. However, recently they experienced slow performance. To futher finding out the root cause, I generated the 802.11 counters report from the WCS and noticed the following parameters is shown. Tx/Rx Fragment Count/Sec and FCS Error Count/Sec
1. Can I make the assumptions that the overall transfer of packet rate in that interval is the Total of Tx/Rx Fragment Count/Sec and FCS Error Count/Sec?
2. If the output rate of Tx/Rx Fragment Count/Sec and FCS Error Count/Sec are the same, does it mean that 50% of the packet are corrupted and this high FCA Error Count/Sec will cause performance degradation to the wireless througphput?
3. What is the baseline of the FCS Error Count/Sec that is acceptable? As for the case with wired, 1% error rate is acceptable. Will wireless have the same baseline?
when running Credential Verification Report, I get following notification: "None of the devices have credential verification data".I have made different Default Device Credential sets that I'm using when I add devices to LMS. I could not see wether this is bug in LMS 4.1 or if I have to do this a different way?
View 1 Replies View RelatedI'm polling a few thousand locations using IP SLA, I have responder enabled on all destinations, and I'm using 60 byte voice packets with a QoS policy.When I run an IP SLA Summary availability report, I have a bunch of locations showing 9% availability 8.5% etc. When I go to the actual collector, and pull up a graph of the same time period, that graph shows 100% availability.
Same collector, same data, just different views giving completely different results. I have to assume that the IP SLA summary report is wrong, these sites were not down 90% of the time.
Just a random though to go with that, I do have the IP SLA to only pull information during the locations operational hours, and I did pull the report from midnight to 11am, the statistics should have been gathered for 4 hours of the 11, which is still higher than 9%, and I would expect all of my locations to report like that, not just a few hundred.
All of the devices are similar in hardware and IOS, and I have verified on a handful that IP SLA responder is enabled, and I see the connections, I have also verified the source configuration via command line.
I am running CiscoWorks LMS 4.0.1 since 6 months and I wanted to generate today a report about the interface utilization on 2 Cisco switches (Catalyst 3750G). The corresponding job is created, it runs and then i get "succeeded with info" in the "Run Status" column. When I want to click then on the "View Report" link, I get the following error: "Could not generate the report. Either data is not available for the specified duration or the report job failed."
I tried the same procedure with 2 other switches but I have got the same result.
Just looked at report after having upgraded to WCS 7.0. It is reporting that SSH is disabled. It is enabled on the controller. The timeout value was set to zero for telnet access. No indication was given that the telnet timeout value also affected SSH as well. I set the timeout value to a non-zero number and reran the task that generated the report. The Enable SSH line item on the report no longer shows up.
View 2 Replies View RelatedI have just started to discover the power of EEM and am already monitoring config changes on our switches with EEM.I would like to be notified of any interface going up and possibly down. on our 6509's and 3750's This is just to be aware of anyone patching anything in.
View 1 Replies View RelatedI am unable to generate bug summary report in RME. Even I can not generate PSIRT report as well..LMS always gives error "incorrect cisco.com credential. enter correct credential" I have checked my credentials are correct... it gives me error no BTKT:0014..I am using LMS 3.1 attaaching snap shot of my patch level and application version running on LMS...
View 3 Replies View RelatedWhen i am in report generator to create a unused up report i have any of my devices in the devices selector menu. This a same for all reports of the switchport menu. But for the other menu like inventory performance my devices appeard. I make a reboot of my server but no change. I'm looking the logs.
View 4 Replies View RelatedI am setting up reports for tacacs accounting on ACS 5.3. However, accounting only seems to work after entering enable mode on the switch. I would like to see all commands, even the enable command when in privlage 1 mode.
View 2 Replies View RelatedHow to generate a Report for all ur existence Subnet's using LMS 4.2?
View 2 Replies View RelatedI have a problem when doing this report. If I do a device credentials report on a user defined group (40 devices) 11 of these devices fails to connect via SSH. I can make an SSH connection to all 11 devices from the CiscoWorks server, but 11 devices still fails on the report
Device Name Read Community Read Write Community SSH
1. 149.212.XXX.164 Ok Ok Failed to connect.
2. 149.212.XXX.153 Ok Ok Failed to connect.
3. 149.212.XXX.152 Ok Ok Failed to connect.
4. 149.212.XXX.151 Ok Ok Failed to connect.
5. 149.212.XXX.150 Ok Ok Failed to connect.
[code]....
Interface Utilization report displays the interface utilization data for each device polled for the Interface Utilization template. The information is presented using the percentage specifier.
For eg its displayed % (Rx Max%,Rx Avg%,RxMin%,
Tx Max%,Tx Avg%,TxMin%)
I wants report should have the data(interface utilization In Bytes of data)Can we display the data instead of the percentage?
I have ACS 5.2 and would like to know if I can schedule a report to be sent to my email address each Sunday for example for all the failed and succeeded attempts for devices authentication.
View 3 Replies View RelatedDevice performance report of LMS 4.0. You could see picture below about the problem. How do resolve it ?
View 2 Replies View RelatedI would like to create custom reports using the Report Designer (Reports -> Report Designer -> Syslog) and filter certain syslogs from being seen when I run the report like permitted ACL entries, 802.1x successful authentications. It seems like there is only the option of displaying what you want to see, not what you don't want to see.
View 6 Replies View RelatedHas any one identified a way to run a report in Cisco LMS Prime 4.1 to report if switchports have port-security and Sticky-mac enabled?
View 1 Replies View Related