When i am in report generator to create a unused up report i have any of my devices in the devices selector menu. This a same for all reports of the switchport menu. But for the other menu like inventory performance my devices appeard. I make a reboot of my server but no change. I'm looking the logs.
View 4 RepliesHas any one identified a way to run a report in Cisco LMS Prime 4.1 to report if switchports have port-security and Sticky-mac enabled?
View 1 Replies View RelatedCan LMS 4.1 give a report for port capacity in stack switches? We are starting to have issues where our techs are going out and plugging devices into switches and the switches are getting full. We would like to be able to see how many ports are left in each switch.
View 2 Replies View RelatedOn the supervisor card of a cisco 6500 series, according to the following link, [URL] it only has 2 uplink ports on the card. Would I be correct in assuming that I only have those to ports that I can configure IP addresses on?
The cisco that is being devlivere is coming with a 48 port switch and 24 port fibre switch. Could I change any of those ports into a router port and configure IP addresses on those?
The supervisor card is a ws-sup-720-3b the 48 port switch is a ws-x6748-ge-tx the 24 port fibre switch is ws-x6724-sfp
I'm fairly new to Cisco products am in the process of developing my network knowledge on a deeper level. I have a 3825 with a HWIC-4ESW and I'm struggling to fully understand how the two "see" each other. I've setup a V LAN with a layer 3 address on the HWIC and added the switch ports to it. This seemed to allow devices connected to the switch ports to talk to the built-in router ports. I thought this was all making sense until i applied an access-list to the router port. It's a simple ACL i'm just using for testing and the only thing it does is blocks telnet from anywhere. I know the ACL is setup properly because if I connect a device directly to the router port i cannot telnet to the port. However, if i connect a device to one of the switch ports, i am able to telnet to the router port successfully.
It seems that I'm missing something with how traffic flows from the switch port to the router ports and how the two "see" each other.
what is the use of no switch port command in L3 switch?
View 7 Replies View RelatedI was looking for a way to connect an AUX port from a 1700 router to a 6500 switch module console port, to see the output of the Switch's on the 1700 router, in case there is a network downtime, I could see what's going on in the switch, what cable should I use ? Also, is there is any kind of documentation for this type of config what have I seen is very few info.
View 2 Replies View Relatedis it possible to assign a loopback address to a typical switch port on a 2950 switch? I want to be able to have some devices connected to a switch to test access lists and VLANs.
View 3 Replies View RelatedI would like to allow a single computer to easily operate laser scanners one after another. A single laser scanner can create an ip address for it's "network" that a computer can connect to through an ethernet cable.Is it possible to connect a computer to the input port of a switch and to connect the laser scanners to the multiple output ports, then individually access the ports by connecting to each laser scanner's respective ip address?
View 2 Replies View RelatedI currently have an old Linksys WRT54G router with 4 ethernet and 1 internet port. I have an old Sprint 660 modem connected to the router for internet access. I am also using 3 of the 4 ethernet ports for wired devices (main PC, NAS drive and Dish Network net access). I have another PC and a printer connected wirelessly to the router.Now, with my modem going bad, CenturyLink has provided a combo modem/router (EQ660DR-F1) to be used in place of my Linksys router/modem, providing wired, wireless and modem capabilities in one.My problem is that the new router/modem has only one ethernet port along with a DSL port. Obviously, I can connect my main PC to the ethernet port, DSL to the modem port and connect my 2nd PC and printer wirelessly as they are now. How I might connect my other 2 wired devices, possibly by a hub, AP or bridge or some other means? Can one of these be connected by wireless to connect the other 2 devices, or do these have to be connected physically by wire?
View 2 Replies View RelatedHow to configure this setup.I have an ASA5505 with dual wan failover, FiOS (eth0) & Cable (eth1). how to configure the port forwarding for all my devices so it doesn't matter what external interface the traffic is coming from. For example, I need web traffic on port 80 forwarded to 192.168.1.150 regardless of whether it is coming through eth0 or eth1.
View 2 Replies View RelatedUnfortunately we are stuck with a bt homehub 2.0. We all hate this thing with a passion. We cant workout how to open the same port on 2 devices. When we try it says theres a conflict and just refuses to let us do it. So only one of us can play the game we want, without it timing out. Now I've tried the BT forums, there was no support there. I phoned up BT and to my absolute disgust, nobody there knew how to use the homehub, or simply said 'turn off the firewall'.
View 2 Replies View Relatedshow cdp neighbors command shows two devices connected through the same local port?I have a Cisco 3560 that when I issue the "show cdp neighbors" command I get the following results: [code]
the question is why is this showing that Gig0/3 is being used twice to connect to two different devices. I have verified there is no hub connected to this port and in fact Switch3 is not connected to Switch1 at all yet it still shows up in the CDP table.
I have cleared the CDP table on every device at this location and still get the same results.
In my LAN environment, I'm using two cisco SG300-10 switches. Both switches are connected by GE10 on both switches, where both ports are set to trunk.Now on all ports 1-9 on both switches, I'm having client computers attached. So I set ports 1-9 to "access" mode.All interfaces on any switch is left in default vlan.
Is it normal that I see all traffic from all connected devices on any port where I connect a listening device?What I'd like to achieve is, that only traffic that is meant for a specific workstation is actually forwarded to this workstation. By now it seems that I get all the traffic from everybody.
I'm new to CiscoWorks and I inherited the system in my new job. We are running LMS 3.2 and I want to run a report to see what versions of IOS that are running on the network.
View 3 Replies View RelatedUnable to run Eos/EoL report, I get error that my cisco.com credential are not valid, I verified my credential and they work fine. I'm running RME4.3.2 on Solaris 10.
View 3 Replies View RelatedI have cisco acs 5.3 appliance. Issue is, when i view tacacs accounting it only shows 100 pages of records. So first kindly tell me if this is the limitation of acs 5.3 to only show 100 pages. Secondly if i want to export the report of last 30 days, its also not showing the last 30 days.
How to get the report of last 30 days
I have an issue with rme 4.2 from LMS 3.1 When I try to generate a syslog report this shows me nothing. I locate SyslogCollector.log file and I see sometnig wrong.
View 4 Replies View RelatedIs it possible to run an uptime report using CWLMS 3.2 ?
View 2 Replies View RelatedI am using LMS version 3.2 and i am not able to generate EOS/EOL report with error no connection to Cisco.Saw an update i LMS portal as this:
Now Available! LMS 3.2:Patch for un-interrupted service of Cisco.com download for Device/Software/PSIRT/EOX updates (To be applied on or before 15-June-2011)
so upgraded the patch cwcs33x-win-CSCto46927-0.zip and restarted the demeon as read in the read me file for the patch.Now the job execution status is always shows running, its neither fail nor pass.
My customer recently deployed WLCs and WCS in their environment. However, recently they experienced slow performance. To futher finding out the root cause, I generated the 802.11 counters report from the WCS and noticed the following parameters is shown. Tx/Rx Fragment Count/Sec and FCS Error Count/Sec
1. Can I make the assumptions that the overall transfer of packet rate in that interval is the Total of Tx/Rx Fragment Count/Sec and FCS Error Count/Sec?
2. If the output rate of Tx/Rx Fragment Count/Sec and FCS Error Count/Sec are the same, does it mean that 50% of the packet are corrupted and this high FCA Error Count/Sec will cause performance degradation to the wireless througphput?
3. What is the baseline of the FCS Error Count/Sec that is acceptable? As for the case with wired, 1% error rate is acceptable. Will wireless have the same baseline?
when running Credential Verification Report, I get following notification: "None of the devices have credential verification data".I have made different Default Device Credential sets that I'm using when I add devices to LMS. I could not see wether this is bug in LMS 4.1 or if I have to do this a different way?
View 1 Replies View RelatedI'm polling a few thousand locations using IP SLA, I have responder enabled on all destinations, and I'm using 60 byte voice packets with a QoS policy.When I run an IP SLA Summary availability report, I have a bunch of locations showing 9% availability 8.5% etc. When I go to the actual collector, and pull up a graph of the same time period, that graph shows 100% availability.
Same collector, same data, just different views giving completely different results. I have to assume that the IP SLA summary report is wrong, these sites were not down 90% of the time.
Just a random though to go with that, I do have the IP SLA to only pull information during the locations operational hours, and I did pull the report from midnight to 11am, the statistics should have been gathered for 4 hours of the 11, which is still higher than 9%, and I would expect all of my locations to report like that, not just a few hundred.
All of the devices are similar in hardware and IOS, and I have verified on a handful that IP SLA responder is enabled, and I see the connections, I have also verified the source configuration via command line.
I am running CiscoWorks LMS 4.0.1 since 6 months and I wanted to generate today a report about the interface utilization on 2 Cisco switches (Catalyst 3750G). The corresponding job is created, it runs and then i get "succeeded with info" in the "Run Status" column. When I want to click then on the "View Report" link, I get the following error: "Could not generate the report. Either data is not available for the specified duration or the report job failed."
I tried the same procedure with 2 other switches but I have got the same result.
We have a new 4507R-E Switch which RME keeps reporting as "CONFIG_CHANGE" each evening. When you click to see the change, the only thing that has changes is the "ntp clock-period".
However, we have configured "ntp clock-period" as an exclude command in RME Config Managment.
I need to understand why change audit report reports an unused username Name of the user who performed the change. This is the name entered when the user logged in. It can be the name under which the LMS application is running, or the name using which the change was performed on the device. #The User Name field may not always reflect the user name. The User Name is reflected only when: A config change was performed using LMS. #A config change was performed outside of LMS, but the network has username-based AAA security model, wherein authentication is performed by an AAA server, which could be TACACS/RADIUS or local.
View 2 Replies View RelatedJust looked at report after having upgraded to WCS 7.0. It is reporting that SSH is disabled. It is enabled on the controller. The timeout value was set to zero for telnet access. No indication was given that the telnet timeout value also affected SSH as well. I set the timeout value to a non-zero number and reran the task that generated the report. The Enable SSH line item on the report no longer shows up.
View 2 Replies View RelatedI have just started to discover the power of EEM and am already monitoring config changes on our switches with EEM.I would like to be notified of any interface going up and possibly down. on our 6509's and 3750's This is just to be aware of anyone patching anything in.
View 1 Replies View RelatedI am unable to generate bug summary report in RME. Even I can not generate PSIRT report as well..LMS always gives error "incorrect cisco.com credential. enter correct credential" I have checked my credentials are correct... it gives me error no BTKT:0014..I am using LMS 3.1 attaaching snap shot of my patch level and application version running on LMS...
View 3 Replies View RelatedI am setting up reports for tacacs accounting on ACS 5.3. However, accounting only seems to work after entering enable mode on the switch. I would like to see all commands, even the enable command when in privlage 1 mode.
View 2 Replies View RelatedHow to generate a Report for all ur existence Subnet's using LMS 4.2?
View 2 Replies View RelatedI have a problem when doing this report. If I do a device credentials report on a user defined group (40 devices) 11 of these devices fails to connect via SSH. I can make an SSH connection to all 11 devices from the CiscoWorks server, but 11 devices still fails on the report
Device Name Read Community Read Write Community SSH
1. 149.212.XXX.164 Ok Ok Failed to connect.
2. 149.212.XXX.153 Ok Ok Failed to connect.
3. 149.212.XXX.152 Ok Ok Failed to connect.
4. 149.212.XXX.151 Ok Ok Failed to connect.
5. 149.212.XXX.150 Ok Ok Failed to connect.
[code]....
Interface Utilization report displays the interface utilization data for each device polled for the Interface Utilization template. The information is presented using the percentage specifier.
For eg its displayed % (Rx Max%,Rx Avg%,RxMin%,
Tx Max%,Tx Avg%,TxMin%)
I wants report should have the data(interface utilization In Bytes of data)Can we display the data instead of the percentage?