Just looked at report after having upgraded to WCS 7.0. It is reporting that SSH is disabled. It is enabled on the controller. The timeout value was set to zero for telnet access. No indication was given that the telnet timeout value also affected SSH as well. I set the timeout value to a non-zero number and reran the task that generated the report. The Enable SSH line item on the report no longer shows up.
View 2 RepliesI try to export a Detailed Device Report to a CSV. It failes:
<HTML><META HTTP-EQUIV="content-type" CONTENT="text/html;charset=utf-8">
<H1>HTTP Status 500 - </H1><HR SIZE=1 noShade>
<P><B>type</B> Exception report</P><P><B>message</B> <U></U></P><P><B>description</B> <U>The server encountered an internal error () that prevented it from fulfilling this request.</U></P><P><B>exception</B>
[code].....
Exporting to PDF works OK.CW is running on Windows server. RME is 4.3.1
Has any one identified a way to run a report in Cisco LMS Prime 4.1 to report if switchports have port-security and Sticky-mac enabled?
View 1 Replies View RelatedI cannot find the way to select another index Key on WEP. I have already upgraded the farmware to 10.02 still a same.
View 4 Replies View RelatedI have setup a disk on the USB port of the EA4500 and have 4 folders. One being music. I want to access this folder via my Wireless laptop with Windows Media Player but I only get a handful of the 3000+ songs on the disk. A hard wired PC can access the files but not a wireless laptop. I'm not sure where the issue is. If I use the drive via //host/Music the Star ratings are not available but I get all music, if I map a drive then I get star rating but only a handful of songs. I have tried to change permission but I cannot change the file permissions on the Linksys.
View 1 Replies View RelatedHow to get the Detailed Device View in LMS 4.0 ? From what I have been able to find out I should be able to go do Monitor> Fault Settings> Setup> Fault Device Details, select a device, click View and then click the device name link.Unfortunately the device name(s) displayed are not links, just text.
I need to get the the Detailed Device View so that I can block certain interfaces/events from generating alarms, specifically ISDNB channels when voice calls are made.
I've got a Catalyst 3560G, and I want to reset the current index for a DHCP pool. I could remove the leases given for that pool, but I couldn't find this option.
View 3 Replies View RelatedAny document in which is specified who may ACE rules are supported in an ASA5585-SSP-20?I need to compare this an other several specification versus a FWSM. I found the information for the module, but not for the ASA 5585-X..In the data sheet this information is not specified.
View 5 Replies View RelatedI need to count traffic used by each device connected to the access point.
The manual says: In addition to the standard event log, the access point can send a detailed log to an external Syslog server. The access point’s Syslog captures all log activities and includes this information about all data transmissions: every connection source and destination IP address, IP server, and number of bytes transferred.
How do I get that detailed log sent to a local IP address? All I managed to get so far is standard log - configuration changes and authentication messages.
Is there a way to configure Belkin N750 DB not to index the images/photos but only and audio and video files?
View 1 Replies View RelatedI have a WAP4410N access Point, firmware 2.0.1.0. I have configured a Kiwi syslog server to get the log from the WAP4410N, but the log information obtained is just the "standard event log" and not the detailed log (every connection source and destination IP address,IP server,and number of bytes transferred) , according to the manual of the access point.what I have to do? firmware update? another syslog server?
View 1 Replies View Relatedwhere I can find detailed documentation on these two products. Particularly, I am looking for high availability capabilities and any license requirements.
View 1 Replies View Relatedwe have bought 2911 router recently has to set up VOIP line seperately for the network we have two two broadband service provider:
1. how can i use 1 line as an active and other line as a failover(when 1 line is down other line should automatically bear the traffic).clear config will be useful. NATTING using MAtch address objects( roughly )
broadband service provider 1: 97.89.X.X 255.255.252.0
broadband service provider 2: 10.0.x.x 255.255.240.0
2. there are only 20 users to set up a voip line now. here we have telecom provider where they should route the traffic to make any international calls( say telecom public ip 200.200.109.110)from lan - wan everything is allowed from wan -lan we have to allow only telcom provider IP(200.200.109.110)
I'm new to CiscoWorks and I inherited the system in my new job. We are running LMS 3.2 and I want to run a report to see what versions of IOS that are running on the network.
View 3 Replies View RelatedUnable to run Eos/EoL report, I get error that my cisco.com credential are not valid, I verified my credential and they work fine. I'm running RME4.3.2 on Solaris 10.
View 3 Replies View RelatedI have cisco acs 5.3 appliance. Issue is, when i view tacacs accounting it only shows 100 pages of records. So first kindly tell me if this is the limitation of acs 5.3 to only show 100 pages. Secondly if i want to export the report of last 30 days, its also not showing the last 30 days.
How to get the report of last 30 days
I have an issue with rme 4.2 from LMS 3.1 When I try to generate a syslog report this shows me nothing. I locate SyslogCollector.log file and I see sometnig wrong.
View 4 Replies View RelatedIs it possible to run an uptime report using CWLMS 3.2 ?
View 2 Replies View RelatedI am using LMS version 3.2 and i am not able to generate EOS/EOL report with error no connection to Cisco.Saw an update i LMS portal as this:
Now Available! LMS 3.2:Patch for un-interrupted service of Cisco.com download for Device/Software/PSIRT/EOX updates (To be applied on or before 15-June-2011)
so upgraded the patch cwcs33x-win-CSCto46927-0.zip and restarted the demeon as read in the read me file for the patch.Now the job execution status is always shows running, its neither fail nor pass.
My customer recently deployed WLCs and WCS in their environment. However, recently they experienced slow performance. To futher finding out the root cause, I generated the 802.11 counters report from the WCS and noticed the following parameters is shown. Tx/Rx Fragment Count/Sec and FCS Error Count/Sec
1. Can I make the assumptions that the overall transfer of packet rate in that interval is the Total of Tx/Rx Fragment Count/Sec and FCS Error Count/Sec?
2. If the output rate of Tx/Rx Fragment Count/Sec and FCS Error Count/Sec are the same, does it mean that 50% of the packet are corrupted and this high FCA Error Count/Sec will cause performance degradation to the wireless througphput?
3. What is the baseline of the FCS Error Count/Sec that is acceptable? As for the case with wired, 1% error rate is acceptable. Will wireless have the same baseline?
when running Credential Verification Report, I get following notification: "None of the devices have credential verification data".I have made different Default Device Credential sets that I'm using when I add devices to LMS. I could not see wether this is bug in LMS 4.1 or if I have to do this a different way?
View 1 Replies View RelatedI'm polling a few thousand locations using IP SLA, I have responder enabled on all destinations, and I'm using 60 byte voice packets with a QoS policy.When I run an IP SLA Summary availability report, I have a bunch of locations showing 9% availability 8.5% etc. When I go to the actual collector, and pull up a graph of the same time period, that graph shows 100% availability.
Same collector, same data, just different views giving completely different results. I have to assume that the IP SLA summary report is wrong, these sites were not down 90% of the time.
Just a random though to go with that, I do have the IP SLA to only pull information during the locations operational hours, and I did pull the report from midnight to 11am, the statistics should have been gathered for 4 hours of the 11, which is still higher than 9%, and I would expect all of my locations to report like that, not just a few hundred.
All of the devices are similar in hardware and IOS, and I have verified on a handful that IP SLA responder is enabled, and I see the connections, I have also verified the source configuration via command line.
I am running CiscoWorks LMS 4.0.1 since 6 months and I wanted to generate today a report about the interface utilization on 2 Cisco switches (Catalyst 3750G). The corresponding job is created, it runs and then i get "succeeded with info" in the "Run Status" column. When I want to click then on the "View Report" link, I get the following error: "Could not generate the report. Either data is not available for the specified duration or the report job failed."
I tried the same procedure with 2 other switches but I have got the same result.
We have a new 4507R-E Switch which RME keeps reporting as "CONFIG_CHANGE" each evening. When you click to see the change, the only thing that has changes is the "ntp clock-period".
However, we have configured "ntp clock-period" as an exclude command in RME Config Managment.
I need to understand why change audit report reports an unused username Name of the user who performed the change. This is the name entered when the user logged in. It can be the name under which the LMS application is running, or the name using which the change was performed on the device. #The User Name field may not always reflect the user name. The User Name is reflected only when: A config change was performed using LMS. #A config change was performed outside of LMS, but the network has username-based AAA security model, wherein authentication is performed by an AAA server, which could be TACACS/RADIUS or local.
View 2 Replies View RelatedI have just started to discover the power of EEM and am already monitoring config changes on our switches with EEM.I would like to be notified of any interface going up and possibly down. on our 6509's and 3750's This is just to be aware of anyone patching anything in.
View 1 Replies View RelatedI am unable to generate bug summary report in RME. Even I can not generate PSIRT report as well..LMS always gives error "incorrect cisco.com credential. enter correct credential" I have checked my credentials are correct... it gives me error no BTKT:0014..I am using LMS 3.1 attaaching snap shot of my patch level and application version running on LMS...
View 3 Replies View RelatedWhen i am in report generator to create a unused up report i have any of my devices in the devices selector menu. This a same for all reports of the switchport menu. But for the other menu like inventory performance my devices appeard. I make a reboot of my server but no change. I'm looking the logs.
View 4 Replies View RelatedI am setting up reports for tacacs accounting on ACS 5.3. However, accounting only seems to work after entering enable mode on the switch. I would like to see all commands, even the enable command when in privlage 1 mode.
View 2 Replies View RelatedHow to generate a Report for all ur existence Subnet's using LMS 4.2?
View 2 Replies View RelatedI have a problem when doing this report. If I do a device credentials report on a user defined group (40 devices) 11 of these devices fails to connect via SSH. I can make an SSH connection to all 11 devices from the CiscoWorks server, but 11 devices still fails on the report
Device Name Read Community Read Write Community SSH
1. 149.212.XXX.164 Ok Ok Failed to connect.
2. 149.212.XXX.153 Ok Ok Failed to connect.
3. 149.212.XXX.152 Ok Ok Failed to connect.
4. 149.212.XXX.151 Ok Ok Failed to connect.
5. 149.212.XXX.150 Ok Ok Failed to connect.
[code]....
Interface Utilization report displays the interface utilization data for each device polled for the Interface Utilization template. The information is presented using the percentage specifier.
For eg its displayed % (Rx Max%,Rx Avg%,RxMin%,
Tx Max%,Tx Avg%,TxMin%)
I wants report should have the data(interface utilization In Bytes of data)Can we display the data instead of the percentage?
I have ACS 5.2 and would like to know if I can schedule a report to be sent to my email address each Sunday for example for all the failed and succeeded attempts for devices authentication.
View 3 Replies View Related