Cisco Wireless :: WAP4410N Detailed Log With Syslog Server?
Feb 7, 2011
I have a WAP4410N access Point, firmware 2.0.1.0. I have configured a Kiwi syslog server to get the log from the WAP4410N, but the log information obtained is just the "standard event log" and not the detailed log (every connection source and destination IP address,IP server,and number of bytes transferred) , according to the manual of the access point.what I have to do? firmware update? another syslog server?
View 1 Replies
ADVERTISEMENT
Jun 18, 2012
I need to count traffic used by each device connected to the access point.
The manual says: In addition to the standard event log, the access point can send a detailed log to an external Syslog server. The access point’s Syslog captures all log activities and includes this information about all data transmissions: every connection source and destination IP address, IP server, and number of bytes transferred.
How do I get that detailed log sent to a local IP address? All I managed to get so far is standard log - configuration changes and authentication messages.
View 6 Replies
View Related
Jan 15, 2012
Recently i have upgraded the IOS of ASA5550 (in HA mode) to 8.4.2 from 8.0.5, after OS upgrade we found that the syslog from thses firewalls are not getting captured/transfered to centralised syslog server. The server is reachable from the firewalls.
View 3 Replies
View Related
Jul 26, 2011
I have a WCS working on version 7.0.172.0.Is there a way to send the alarms produced by WCS to another Syslog Server?
View 4 Replies
View Related
Mar 4, 2012
I am trying to setup syslog server on LMS 4.0.Everything seems to be working fine but I have a lot of stragne logs in my syslog.log file.Every single day I receive logs like :
Mar 05 09:31:03 127.0.0.1 100: <30> dmgt[1136]: 3007(I):Started application(1015) "e:CSCOpxincwjava.exe -cw:jre lib/jre -cp e:CSCOpxMDC omcatsharedlibMICE.jar;e:CSCOpxMDC omcatsharedlibNATIVE.jar;e:CSCOpxMDC omcatsharedlibjdom.jar;e:CSCOpxMDC omcatsharedlibxalan.jar;e:CSCOpxMDC omcatsharedlibxerces.jar;e:CSCOpxMDC omcatcommonlibservlet.jar;e:CSCOpxMDC omcatsharedlibcastor-0.9.5.jar;e:CSCOpxMDC omcatsharedlibcastor-0.9.5-xml.jar;e:CSCOpxlibclasspath;e:CSCOpxwwwclasspath;wwwclasspathvbjorb.jar;MDC omcatwebappsupmWEB-INFclasses;libjrelibendorsedjacorb.jar;MDC omcatwebappsupmWEB-INFlibctm.jar;MDC omcatwebappsupmWEB-INFliblog4j.jar;MDC omcatwebappsupmWEB-INFlibjep-3.2.0.jar;MDC omcatwebappsupmWEB-
[code]....
I dont want to get any logs from 127.0.0.1. Is it possible to filter out logs from server ?
View 3 Replies
View Related
May 9, 2011
I need to setup a syslog server for PIX w/ 6.2 and was hoping to get detailed instruction how to go about it. I would like exact syntax w/ an example on the pix and any configuration on the computer that will be receiving the log info. I have downloaded tftpd32 onto computer
View 1 Replies
View Related
May 16, 2012
I would like to know whether LMS 4.1 (local server mode) has the ability to relay syslog messages received from devices to an external syslog server? If so, how do I configure such?
From reading the document and going through the LMS 4.1 GUI, it appears that it could receive and forward messages but only between LMS system (ie. multi server mode) as SSL is required.
View 1 Replies
View Related
Feb 12, 2012
I want to forward syslog messages that I receive in my Cisco Works server to another server,what is the best way to accomplish this. I'm running LMS3.2 on Solaris 10.
View 3 Replies
View Related
Mar 9, 2013
I'm having an issue with the syslog.
My configuration is:
LAN A (RV042)<-> GW to GW tunnel <-> (RV082) LAN B
On LAN A, I got a NAS with a syslog server. On the RV042, I've set the parameters for the syslog server, and it's working fine. On the RV082, I've set the same parameters and noting is happening.
As troubleshooting, I've done the following:
-On the RV082, I can ping the NAS without problems.
-On the RV082, I've set my computer IP adress as syslog server IP and with packet analyser, I not seing any UDP packets.
View 6 Replies
View Related
Jan 16, 2013
Is there an .ISO file for installing on Windows Server20888SR2 ?
View 1 Replies
View Related
Mar 19, 2013
I got a new Cisco 3845 under my adminsitration. For some special events I do automated actions (e-mail's) from Cisco Works 2000.
One is if power supply fails. Problem now is, tha a ps fail message will be repeated every 20 seconds to syslog server - but local log on router only once.
View 1 Replies
View Related
Dec 25, 2012
How to set up logging of commands on syslog server ? (cisco nexus 7010)
View 2 Replies
View Related
Oct 26, 2011
We use multiple ASA 5500/5580 cluster systems running 8.3 software versions.Actually we send all our FW syslog data to a SIEM appliance in a DMZ on a remote firewall (non-asa). Recently we suffered a strange incident while implementing a new SIEM collection station now situated in a dmz that is located on one of the ASA contexts. We redirected the syslog streams to the new client for one of the contexts on the ASA cluster that holds the new SIEM agent DMZ..since we did this and redirected the syslog we see double traffic and spoofing errors on that context
a/ the ASA keeps sending out the syslog traffic to the OLD SIEM agent server ip (there is however no trace of its ip in the config)
b/ the traffic leaving the interconnection interface towards the OLD SIEM agent gets a SPOOFING error on the traffic
c/ strangely the data gets also correctly forwarded to the new SIEM collection stations.
We started out with redirecting traffic on only one of the 5 contexts to the new environment and kept logging the others to the old system.I finally got out of the issue by reconfiguring al the other contexts to forward their syslog towards the same new server , since that moment we no longer have the double logging and spoofing error , all syslog traffic goes correctly to the new SIEM agent. It looked like some remenants of the old syslog config remainded on the asa event after deleting and introducing a new config line (we used the asdm to execute the action) as said either it kept the old config or it looked in the other context and "decided" to keep sending to the old server also mentioned in that syslog can find the behaviour in any buglists either way.
View 1 Replies
View Related
Mar 13, 2011
i'm about to configure a syslog server to receive syslog messages from a Cisco ASA5510 and being it a one week test I was wondering how much space should I allocate on the machine hosting the tool (kiwi syslog). I see that the ASA fills the internal syslog buffer to 4MB and then it overrides it. How many messages would those 4MB be?
View 2 Replies
View Related
Dec 12, 2011
I am sending TACACS administration logging to a syslog server. When the messages show up on the syslog server, they are 5 hours ahead of the actual time. Time on the ACS is correct - local logging shows the correct time. Time on the syslog server is correct...all other devices/systems sending syslog messages to it are coming through with the correct time. why the ACS syslog messages would be 5 hours ahead?
View 3 Replies
View Related
Jul 7, 2012
Add the ability to send syslog events to multiple syslog servers in the SA500 Series routers. I know the functionality is currently in the RV220W because we utilized it. It would be great if you could configure the syslog servers by event type as well. For example, being able to send the kernel events to syslog server A, and all other events to syslog server B.
View 0 Replies
View Related
Apr 27, 2012
I can't seem to send config changes to our syslog server on a 2950, I'm fine with 2960's and 3750's. The Cisco 2955 is using the latest IOS c2955-i6k2l2q4-mz.121-22.EA14.bin.
Here is what I have added:
logging buffered 64000 debugging
logging console informational
logging monitor informational
[Code].....
The only sylog message I get is "Configured from console by username on vty0 (10.1.1.35)
View 5 Replies
View Related
Aug 8, 2011
Can i send "show conn" to syslog server? for example:
[code]...
ESTAB5082
View 1 Replies
View Related
Apr 30, 2011
I have the following equipment:
Cisco 871W router
2x WAP 4410N APs running 2.0.3.3
I currently have 1 AP connected to the router via copper. The AP to AP link is over 802.11. I have attached a diagram reflecting the current topology.
The AP-to-AP link will come up utilizing B/G/N mixed mode; however, the connection is basically unusable. About 30% of the traffic is dropped, while the packets that do make it have a consistently volatile latency, anywhere from 15 to 1500 ms. I have had success using G-only and B/G mixed. The link is stable (I have had the best results with B/G). The problem is, I didn't buy the 2nd 4410N to run the G protocol. I would like to connect the APs running either B/G/N (hopefully negotiating to N) or N only. I am wondering if there is a certain configuration I can utilize (perhaps using WDS repeater or bridge versus Wireless Client/Repeater?), or a firmware upgrade set for release that can make this happen for me.
View 1 Replies
View Related
Feb 5, 2012
I'm looking to configure a syslog server for all of my cisco device logging. I've had a look at CNA and can't find any options to define a syslog server for my switches.
What's the best way to define a syslog server and the severity of the notifications? Also, i'm looking to clear all previous Syste mmessages fon my devices?
View 6 Replies
View Related
May 5, 2013
I'm trying to view the logs from a Cisco 857W router to a workstation running the Kiwi Syslog server. what I've done is the following:
Config term
Logging on
Logging source-interface BVI1
Logging Facility Local7 (or any other facility you want to allocate for this router.)
Logging [IP Address or Hostname of machine running Kiwi Syslog Server]
End
I see noting on the syslog server. Although I can see the log information on the router Also is there a command to stop the logging from generating or is this on by default.
View 1 Replies
View Related
Apr 16, 2013
I have installed a switch (3560) that was from another site and changed all it's config and hostname etc and it is now live, however the syslog messages still see the old hostname, what could be causing this?
View 3 Replies
View Related
Dec 21, 2011
I have configured my 2951 router to send logs to my Kiwi syslog server like below.
#logging 10.20.20.52
But I am not receiving any logs from my router, the same has configured on my asa5520 and its sending logs.
View 3 Replies
View Related
Jun 27, 2011
I have recently setup Splunk to receive my syslog messages from my ASA 5510. In the past I used kiwi without observing this issue, but I needed more features than kiwi had available. Anyway, anytime I stop the splunk service my asa does not allow any outbound connections to be established.
View 2 Replies
View Related
Dec 15, 2012
I am using Solawinds syslog and trying to get our Cisco routers send syslogs to our syslog server. I followed the procedure on Configuring Cisco Devices to Use a Syslog Server from [URL] Our Cisco swtches are all sending syslog messages but not the routers. I compared the config with our access switches but can't seem to find the problem:
Sample router config:
service nagleno service padservice tcp-keepalives-inservice tcp-keepalives-outservice timestamps debug datetime msec localtime show-timezoneservice timestamps log datetime msec localtime show-timezoneservice password-encryption!hostname WWF-RT1boot-start-markerboot-end-marker!security authentication failure rate 10 logsecurity passwords min-length 8logging buffered 4096logging rate-limit all 10logging console critical!aaa new-model!!
[Code] .......
is there a command that prevents the router from sending the syslog to the server?
View 2 Replies
View Related
May 13, 2013
I am trying to configure a WAP4410N, with latest firmware, for disabled security (i.e.: no WEP/WPA, user passwords etc) but enable MAC authentication control using RADIUS.If I test the WAP using disabled security and disabled authentication control, the WAP works fine. When I enable the RADIUS MAC authentication (ensuring I have entered the correct RADIUS server details) nothing happens, the WAP connection just fails. Also, the RADIUS server doesn't log any attempts from the WAP to connect.Is there a known problem with this WAP simply not working with RADIUS under this configuration?
View 1 Replies
View Related
Nov 28, 2012
How to get the Detailed Device View in LMS 4.0 ? From what I have been able to find out I should be able to go do Monitor> Fault Settings> Setup> Fault Device Details, select a device, click View and then click the device name link.Unfortunately the device name(s) displayed are not links, just text.
I need to get the the Detailed Device View so that I can block certain interfaces/events from generating alarms, specifically ISDNB channels when voice calls are made.
View 4 Replies
View Related
Nov 9, 2010
Just looked at report after having upgraded to WCS 7.0. It is reporting that SSH is disabled. It is enabled on the controller. The timeout value was set to zero for telnet access. No indication was given that the telnet timeout value also affected SSH as well. I set the timeout value to a non-zero number and reran the task that generated the report. The Enable SSH line item on the report no longer shows up.
View 2 Replies
View Related
Aug 29, 2012
Any document in which is specified who may ACE rules are supported in an ASA5585-SSP-20?I need to compare this an other several specification versus a FWSM. I found the information for the module, but not for the ASA 5585-X..In the data sheet this information is not specified.
View 5 Replies
View Related
Aug 7, 2012
where I can find detailed documentation on these two products. Particularly, I am looking for high availability capabilities and any license requirements.
View 1 Replies
View Related
Apr 15, 2010
I try to export a Detailed Device Report to a CSV. It failes:
<HTML><META HTTP-EQUIV="content-type" CONTENT="text/html;charset=utf-8">
<H1>HTTP Status 500 - </H1><HR SIZE=1 noShade>
<P><B>type</B> Exception report</P><P><B>message</B> <U></U></P><P><B>description</B> <U>The server encountered an internal error () that prevented it from fulfilling this request.</U></P><P><B>exception</B>
[code].....
Exporting to PDF works OK.CW is running on Windows server. RME is 4.3.1
View 11 Replies
View Related
Dec 8, 2011
we have bought 2911 router recently has to set up VOIP line seperately for the network we have two two broadband service provider:
1. how can i use 1 line as an active and other line as a failover(when 1 line is down other line should automatically bear the traffic).clear config will be useful. NATTING using MAtch address objects( roughly )
broadband service provider 1: 97.89.X.X 255.255.252.0
broadband service provider 2: 10.0.x.x 255.255.240.0
2. there are only 20 users to set up a voip line now. here we have telecom provider where they should route the traffic to make any international calls( say telecom public ip 200.200.109.110)from lan - wan everything is allowed from wan -lan we have to allow only telcom provider IP(200.200.109.110)
View 7 Replies
View Related
Oct 24, 2012
I can't figure out how to disable the syslog counter on my 1131AG WAP. See the below example log, the counter (number 3614) is right next to the hostname and increments with every syslog message:
Oct 25 07:31:10 airhead 3614: %DOT11-6-ASSOC: Interface Dot11Radio0, Station 7c61.93a4.8332 Associated KEY_MGMT[WPAv2 PSK]
I've tried both of the following commands, neither one removes the counter:
no service sequence-numbers
no logging count
Version Info:
Cisco IOS Software, C1130 Software (C1130-K9W7-M), Version 12.4(10b)JDA, RELEASE SOFTWARE (fc1)
BOOTLDR: C1130 Boot Loader (C1130-BOOT-M) Version 12.3(8)JEA, RELEASE SOFTWARE (fc2)
how to rid the syslog counter
View 1 Replies
View Related
