I've got a Catalyst 3560G, and I want to reset the current index for a DHCP pool. I could remove the leases given for that pool, but I couldn't find this option.
View 3 Replies
Can you confirm that if I want to disable temporarily a dhcp pool on a 4500, I need just to shutdown the interface VLAN corresponding to a specific dhcp pool?
ip dhcp pool test
network 10.X.27.0 255.255.255.0
default-router 10.15.27.250
[Code].....
Not sure if this is a problem with the switch or the wireless AP connected to the switch, but I have a couple of 3560's, one is a 3560G and the other is a 3560, both have phones and wireless ap's connected to them. The ap's on both of these switches continue to loose there ip address and thus disconnect from the controller. This happens about once a week, but the odd thing is that the phones never loose there ip address. All of my other 3560s and 3560g's that have AP's and phones connected are working fine.
View 2 Replies View Related3750 can not support multiple subnets in it's DHCP server pool config.
Is this an issue that can be fixed with a different iOS or is there a different Cisco switch that I can replace the 3750 with that will handle multiple subnets within an individual pool?
Can a layer 2 cisco 2950 switch be used as a dhcp server with it's own address pool.
View 3 Replies View RelatedI am configuring DHCP pool for voice vlan on cisco 2921 router.
Here is the setup.
2921 router -> 3750 -> 2960 PoE -> 7942 IP Phone
Router Config
ip dhcp excluded-address 10.146.54.1 10.146.89.50
!
ip dhcp pool VoiceVlan
network 10.146.54.0 255.255.255.0
subnet prefix-length 24
dns-server 10.144.68.32 10.144.68.33
option 150 ip 10.146.68.36
default-router 10.146.54.1
netbios-name-server 10.144.68.32 10.144.68.33
netbios-node-type h-node
[code]....
I have configured DHCP snooping on a WS-3560G-48PS running IOS 12.2(58)SE2 ipservicesk9 variant.When I enable DHCP snooping clients don't get IP addresses, when DHCP snooping is disabled, everything works fine.I have set up a SPAN port and run a capture (attached) on the traffic. Wireshark notes the Seconds elapsed field appeared to be encoded in little-endian but only on some packets. Apart from that, I can see nothing wrong with the DHCP Offer responses from my DHCP server.Attachment config.txt contains the interesting parts of the configuration. Please note g0/32 has been set to ARP inspection trust as without working DHCP snooping it would require a static bind.Is there any way of figuring out which option can't be parsed? Is there a way to force forwarding of unparsable DHCP packets while still running DHCP snooping?
View 3 Replies View RelatedI need to reset the channel on my N300 router but in order to do so, I need to log in. The log in screen does not take my existing password. How do I get my current password or reset my password? It should be the simplest thing, but I have found this to be extremely difficult with Belkin.
View 1 Replies View RelatedON ASA, I understand that we can assign a static IP for a specific VPN client, or we can use a DHCP pool to assign IP. Now if I want to create DHCP pools, say pool_A and pool_B, for user A, B and C they use the IP from Pool_A, and user D, E, and F they get the IP from pool_B. Is there a way to do this in ASA?
View 4 Replies View RelatedWe have the configuration below set up in a 3560 switch (addresses and names modified for privacy). We are running out of dynamic IP’s in the current pool (6.35.159.0 – 6.35.159.255). We have a new set of IP’s that we can use (6.44.56.0 – 6.44.57.255 – an additional 512 addresses). Although I can figure out the commands to add a new dhcp pool, secondary subnet, etc., I’ve never done this before so I’m not sure of everything I need to do. The end result I need is that the 3560 needs to be able to hand out IP addresses from the current and new pool to anything connecting to vlan 300 – our datanet where computers access the Internet. What I need to do as far as modifying the vlan, adding the secondary subnet, defining helper IP’s, gateways, whatever, so that computers connecting via vlan 300 have Internet access via either of the pools? I have been told that all I need to do is create the pool, but not sure if that is correct...
[code]....
Does any know what " Last reset from system-reset " means? Is this becouse of a power failure or someone reloading the switch?
View 3 Replies View RelatedCisco IOS 12.4 Basic check to see if the command "ip nat pool" is available?We have 12.2 basic and I know it is in the 12.4 Advanced and 15.1 Basic versions (too large of a jump in version for management). Our budget is very limited so I am hoping that 12.4 Basic has this command.
View 2 Replies View RelatedI am configuring IPSec Remote Access VPN on a ASA 5505. There are one external interface and one internal interface configured on the device. Internal interface connected to subnet 192.168.1.0/24.en VPN client get connected, I would like to assign the IP from some subnet(for example 192.168.2.0/24) other than the current internel subnet (192.168.1.0/24), but the VPN client can still access to 192.168.1.0/24. Is there a way to do this?
View 2 Replies View RelatedCisco 1811W router, IOS 15.1(4)M6, DHCP server not working on internal VLAN but configuration looks OK to me. [code]
View 1 Replies View RelatedI have the network described below, on which I am running PIM.
(network) ---- Embedded Linux Router --(vlan 5)-- CAT 3560G --(vlan 5)-- Cisco 1811 Router ---- Multicast Listener
The Linux Router and the 1811 have formed a PIM neighbor relationship. The multicast listener sends an IGMP Join and I can see the PIM join leave the 1811 router (via "debug ip pim"). Using tcpdump on my linux router I never see the Join come in, but I can see the PIM Hellos (which is why the neighbor relationship formed).
Since two weeks I have a problem with the VLANs who I started to configure. I hope together we find the way.I have 5 VLANS configured in a CISCO 3560G switch. In my windows server 2003 I configured DHCP scope for each VLAN.One of the requirement to connect vlans each other is to put the IP of each vlan as gateway in the clients.So, how can I do to access to internet?. The ip of my Firewall are in one of the VLAN´s.When the configuration of the LAN only had one DHCP scope the gateway was the ip of my firewall. But now i don´t know how to configure the DHCP server, or the firewall, or the switch, or all of them To get access to internet.
View 2 Replies View RelatedMy AP get IP from 6509, but client cannot get dhcp from my dhcp pool for client, what is the reason?i have 3750g switch with integrated WLC, i connect it to 6509 I did all configs yesterday here is outputs
WLC
Interface Name Port Vlan Id IP Address Type Ap Mgr Guest
-------------------------------- ---- -------- --------------- ------- ------ -----
ap-manager LAG 10 172.16.10.100 Static Yes No
globus LAG 20 172.16.20.254 Dynamic No No
management LAG 10 172.16.10.99 Static No No
service-port N/A N/A 0.0.0.0 Static No No
[code].....
I'm trying to set up per vlan routing on a 3560G switch but it's not performing as I would expect. I've got a server on the 109 vlan with a 10.1.9.100 address and a default gateway of 10.1.9.1 this address is an HSRP gateway and currently resides on 10.1.9.7. When I traceroute through to my user PC on the internal network it receives a response from 10.1.9.7 However, it is then denied by an ACL on the internal firewall which has been applied to interface Eth0/0. It should arrive at the firewall on Eth0/2.109 as it has the 10.1.9.4 address.
My goal here is to route traffic on the 101 vlan to a seperate interface on the internal firewall from 109 vlan traffic. I'm either doing something wrong or these routing commands aren't designed to work in the way I'm expecting (I couldn't find any documentation on the ip route command where it is followed by different gateways for different vlans)
interface GigabitEthernet0/12
description Internal-FW Eth0/2
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 109
switchport mode trunk(Code )
I have a 3560G switch with c3560-advipservicesk9-mz.122-46.SE and 2 routers. The switch has vlans defined. I want to route all traffic on vlan 25 out of one of the routers exclusively. Here is what I have attempted:
-Set the SDM template to routing & reload
-Define an access-list for the v lan traffic
-Define the route-map
-Apply the route-map to the vlan interface
When I attempt the last step I receive the following syslog error:
%PLATFORM_PBR-3-UNSUPPORTED_RMAP: Route-map RM_IMDGuest not supported for Policy-Based Routing
Also, the route-map is removed from the vlan interface after this error is thrown. Im 99% confident that PBR is supported on this switch (am I wrong?). Here is the relevant show output:...
access-list 125 permit ip 192.168.25.0 0.0.0.255 any
route-map RM_IMDGuest permit 10
match ip address 125
set ip next-hop 192.168.5.3
[code]....
I have one issue on Vlan in Cisco 3750X switches , I have 2 Offices , I am sitting at corp OFfice and i have one 3750 ( 10.10.1.36)Switch at my location , in my remote office i have one more switch 3750 ( 10.10.33.1) and i am able to access the both vlan IPS with out any issue , now i have some network components in Vlan33 ( 10.10.33.1) at my remote office . i am able to ping 10.10.33.1 IP from my corp office , but i am not able to ping any network devices in 10.10.33.5 example : 10.10.33.5 is my Cyberoam IP at remote location and i am not able to ping , i have taken a trace route and not able to find the issue as i am not much femilar , ping 10.10.33.5 at remote location devicec
I am giving the Configuration for both locaitons below :
10.10.1.36 - Corp Office 3750 Switch:
sh run
L3-#sh running-config
Building configuration...
[Code].....
We are close to receiving our new 6513E chassis which I will be running Sup720 cards in. This will be replacing our existing 6509 Sup2 setup in production. What current IOS version should I run on the Sup720 ? I would like to support SSH. The chassis will be populated with a couple of 6724 SFP cards, 2 6704 10 gig cards and a few 6748 line cards.Is there a good intitial config guide ?
View 6 Replies View Relatedupgrade experience with the 6509E on what IOS version to use. This is a new install, so I want the most current version that supports SSH and works with dual supervisors.
Here is some information:
WS-C5609-E with 983008K/65536K bytes of memory
Current version 12.2(18)SXF17b
Slot 5 Supervisor 720 (Active)
Slot 6 Supervisor 720 (Hot)
Just need a strong base code, no advanced services. Let me know if you any additional information.
What is the inrush current (AC Input Surge Current) for the Cisco 2851 router? Is it the same as the router 2801?
View 1 Replies View RelatedI am facing an issue with setting up dhcp server on a 3750G-24PS-S,IOS : c3560-ipbasek9-mz.122-58.SE.bin,the switch configuration is below,interface Vlan100 description ***Data Segment*** ip address 192.168.102.1 255.255.255.0 no shut!ip dhcp excluded-address 198.168.102.1 198.168.102.10! ,ip dhcp pool datalan network 198.168.102.0 255.255.255.0 default-router 198.168.102.1 dns-server 192.168.40.11,!,interface GigabitEthernet0/1 switchport access vlan 100 switchport mode access spanning-tree portfast.
View 2 Replies View RelatedI want to configure multiple DHCP configuration on ASA 5505. I tried to create sub interface for different IP Pool but it was not configure on ASA 5505. is it possible to create subinterface on ASA 5505?
ASA 5505 IOS version: 8.3(1)
License: Security Plus
I'd like to create dhcp server pool on ASA 5510. I was wondering how big is the DHCP scope that Cisco ASA 5510 can support? Are there any ASA models which can support up to subnet mask 22 for DHCP scope?
View 7 Replies View RelatedI was assigned a task to connect two locations through a L2 VPN, The infrastructure which i have are...
Fortigate 80 C firewall at Location A
CISCO 3560G at Location A
CISCO 3750G at Location B
2 MBPS Leased Line connecting two locations.
T1 line at Location A.
The requirements are as follows..
Both locations should be in the same ip range (ex 10.80.71.1/24) Internet for Location B should be from Location A, both locations should talk to each other.
We have 2 catalyst 3560g-48-PoE protected by a 1000Va 800Watt tripp-lite and I was cheking to see if that is really sufficient. Looking at the charts from Cisco suppport I would think I should have more, but have not had any issues with a few power outages
View 1 Replies View Relatedi facing problem with my switch cisco 3560G, when it power on only System light is green and noting happen. i check with serial cable ( Console) but noting happen no booting.
View 2 Replies View RelatedI have 3560g with 15.0(2)SE2 version. I try to give different default gateways for different interfaces.I've already changed the sdm, run "ip routing" and made interest interfaces in "no switchport" with ip addresses.
my route-map is "
route-map ABC permit 10
set ip next-hop 192.168.77.3"
and it is applied on the interface with "ip policy route-map ABC" but when I try to apply it says "%PLATFORM_PBR-3-UNSUPPORTED_RMAP: Route-map ABC not supported for Policy-Based Routing" everything is fine if I change from "set ip default next-hop" to "set ip next-hop" but it is not I need in the guide of the version it is said this statement is not in unsupported list of route-map commands.[URL]
I have a WS-C3560G-24TS-S running 12.2(50)SE5 with IPBASE. I have been told that the functionality i seek (multicasting) is only available in the IPSERVICES version of the software. I was reading up on upgrading and saw that i needed to do a show license and get the UID and Serial number and get a license that is tied to my box. But the show license command doesnt work wtih my box. i then found something that said that the 3560's were special in that way. Im not sure how to get this box upgraded. I have a different 3560 running the IPSERVICES elsewhere in my organization. Can i take the IOS Version and update my switch to that?
View 3 Replies View RelatedWe currently have two 5548UP and two 2232PP switches running on 5.1(3)N2(1a) and the plan is to connect our old 3560G switches to 2232 PP using enhanced Vpc.
I enabled spanning tree bpdufilter on the 2232 PP ports so that we can connect switches to them but VTP is not working on those ports. Is there anything that needs to be done on the HIFs for VTP to work.Does VTP depends on BPDUs? Does enabling Bpdufilter affects VTP?
We have a problem with the throughput over etherchannel in LACP with 2 or 4 ports. It is iSCSI traffic (vmware esxi 4.1 U3) is going from 2 separate NICs (ports) to the etherchannel (with 2 or 4 ports) that has a SAN connected (Nexenta).
The SAN is configured in passive LACP and the switch is in active LACP. Actually it does not matter if we do LACP or just MODE ON, still same result: ~1GBit/s throughtput in either direction. Like already mentioned, 2 or 4 ports in the etherchannel make no difference, or the configuration of the etherchannel.
I will post some config data below, but here is the question: Why can't we see traffic beyond 1GBit/s? Source and destination are capable of doing much more than that (vmware esxi RAID 5 of 1TB SATA; SAN 16 x 1TB NL-SAS). If we look with CNA, we can see that the traffic is balanced equally over the etherchannel ports. With or without QOS or flowcontrol, no difference. This whole traffic happenes on this switch.
!
port-channel load-balance src-dst-ip
!
interface Port-channel5
[Code]....
