Cisco Wireless :: AP Get IP From 6509 But Client Cannot Get DHCP From Pool
May 30, 2012
My AP get IP from 6509, but client cannot get dhcp from my dhcp pool for client, what is the reason?i have 3750g switch with integrated WLC, i connect it to 6509 I did all configs yesterday here is outputs
WLC
Interface Name Port Vlan Id IP Address Type Ap Mgr Guest
-------------------------------- ---- -------- --------------- ------- ------ -----
ap-manager LAG 10 172.16.10.100 Static Yes No
globus LAG 20 172.16.20.254 Dynamic No No
management LAG 10 172.16.10.99 Static No No
service-port N/A N/A 0.0.0.0 Static No No
[code].....
View 8 Replies
ADVERTISEMENT
Dec 18, 2012
I'm following a tutorial that 'dumbs down' the modem and lets me use the router for everything.
It asks me to set up a static LAN IP (10.x.x.x range) and edit the DHCP pool of the router. When I'm logged in to the routers admin, it doesn't seem I'm able to do any of this.
Earlier in the tutorial it also asked me to set up a static IP for the router, which I did I suppose.
I've added a screenshot of the admin panel, in case that's relevant.
View 1 Replies
View Related
Feb 27, 2013
ON ASA, I understand that we can assign a static IP for a specific VPN client, or we can use a DHCP pool to assign IP. Now if I want to create DHCP pools, say pool_A and pool_B, for user A, B and C they use the IP from Pool_A, and user D, E, and F they get the IP from pool_B. Is there a way to do this in ASA?
View 4 Replies
View Related
Jul 25, 2012
We have the configuration below set up in a 3560 switch (addresses and names modified for privacy). We are running out of dynamic IP’s in the current pool (6.35.159.0 – 6.35.159.255). We have a new set of IP’s that we can use (6.44.56.0 – 6.44.57.255 – an additional 512 addresses). Although I can figure out the commands to add a new dhcp pool, secondary subnet, etc., I’ve never done this before so I’m not sure of everything I need to do. The end result I need is that the 3560 needs to be able to hand out IP addresses from the current and new pool to anything connecting to vlan 300 – our datanet where computers access the Internet. What I need to do as far as modifying the vlan, adding the secondary subnet, defining helper IP’s, gateways, whatever, so that computers connecting via vlan 300 have Internet access via either of the pools? I have been told that all I need to do is create the pool, but not sure if that is correct...
[code]....
View 3 Replies
View Related
Oct 3, 2012
I am configuring IPSec Remote Access VPN on a ASA 5505. There are one external interface and one internal interface configured on the device. Internal interface connected to subnet 192.168.1.0/24.en VPN client get connected, I would like to assign the IP from some subnet(for example 192.168.2.0/24) other than the current internel subnet (192.168.1.0/24), but the VPN client can still access to 192.168.1.0/24. Is there a way to do this?
View 2 Replies
View Related
Sep 16, 2011
Is there any way to always assign the same IP address to an AnyConnect VPN client logged into an ASA 5505 running v8.4?2
View 2 Replies
View Related
Oct 4, 2012
I want to configure multiple DHCP configuration on ASA 5505. I tried to create sub interface for different IP Pool but it was not configure on ASA 5505. is it possible to create subinterface on ASA 5505?
ASA 5505 IOS version: 8.3(1)
License: Security Plus
View 4 Replies
View Related
Jul 16, 2012
I'd like to create dhcp server pool on ASA 5510. I was wondering how big is the DHCP scope that Cisco ASA 5510 can support? Are there any ASA models which can support up to subnet mask 22 for DHCP scope?
View 7 Replies
View Related
May 21, 2012
Can you confirm that if I want to disable temporarily a dhcp pool on a 4500, I need just to shutdown the interface VLAN corresponding to a specific dhcp pool?
ip dhcp pool test
network 10.X.27.0 255.255.255.0
default-router 10.15.27.250
[Code].....
View 3 Replies
View Related
Sep 18, 2012
My question is if I can configure 3 ssid, for 3 different VLAN and add the DHCP address from a WAP4410N AP, when you upgrade to the latest version of IOS I can have this functionality?
View 2 Replies
View Related
Apr 2, 2013
I've got a Catalyst 3560G, and I want to reset the current index for a DHCP pool. I could remove the leases given for that pool, but I couldn't find this option.
View 3 Replies
View Related
Mar 25, 2012
3750 can not support multiple subnets in it's DHCP server pool config.
Is this an issue that can be fixed with a different iOS or is there a different Cisco switch that I can replace the 3750 with that will handle multiple subnets within an individual pool?
View 1 Replies
View Related
Mar 28, 2012
I was trying to set a DHCP pool with 127.16.0.0/16 with RV220W, however, RV220W UI can't save it. It displays "IP Address Range -"Step to reproduce: (it is 100% reproducible)
1. login into RV220W admin web
2. Create a VLAN, id 201
3. Go to "Multiple VLAN subnets", select the VLAN, click edit
4. Enter following info:
IP Address: 172.16.0.1
Subnet Mask: 255.255.0.0
DHCP Mode: DHCP Server
Domain Name: Cisco
Starting IP Address: 172.16.2.100
Ending IP Address: 172.16.10.254
Primary DNS Server: 172.16.0.1
Leave rest of settings with default value.
DNS proxy is enabled
5. Press Save button. The UI shows text "IP Address Range -".
Expected result: RV220W shall save the setting and make use of 172.16.0.0 subnet in IP pool. By the way, the error message "IP Address Range -" seems incompleteI tried same setting on netgear FVS318N (very similar settings to RV220W), it accepts 172.16.0.0/16 as DHCP IP pool and works.RV220W has great feature set meets my needs. Its UI is slow and sometime dashboard freezes, which I can live with comparing to features. But DHCP server IP pool can't be class B is huge limitation to me.
View 1 Replies
View Related
Mar 18, 2009
Can a layer 2 cisco 2950 switch be used as a dhcp server with it's own address pool.
View 3 Replies
View Related
Feb 12, 2013
I am configuring DHCP pool for voice vlan on cisco 2921 router.
Here is the setup.
2921 router -> 3750 -> 2960 PoE -> 7942 IP Phone
Router Config
ip dhcp excluded-address 10.146.54.1 10.146.89.50
!
ip dhcp pool VoiceVlan
network 10.146.54.0 255.255.255.0
subnet prefix-length 24
dns-server 10.144.68.32 10.144.68.33
option 150 ip 10.146.68.36
default-router 10.146.54.1
netbios-name-server 10.144.68.32 10.144.68.33
netbios-node-type h-node
[code]....
View 1 Replies
View Related
Jul 10, 2012
We have a scenario where the Cisco ASA 5505 will be one end of a site-to-site VPN. The same ASA 5505 also allows Client VPN connection. The question is around IP pooling. If I assign a pool of IP's (192.168.1.20 - 192.168.1.30) for Client VPN connections - do I need to be sure that those same IP's are not used on the other side of site-to-site VPN ?
There could be PC's/Servers running 192.168.1.0/24 on the other side of site-to-site VPN. Would this cause an address conflict ?
View 4 Replies
View Related
Apr 21, 2013
Do the problem caused by the modems itself or it just sign of faulty Ethernet switch (using 20 port Allied Telesis ethernet switch).
Sometimes I cannot connect to internet due to "unidentified network" buy i can resolve this problem by restarting my modem + switch.
View 4 Replies
View Related
Feb 4, 2013
I have a WLC5508 , we are using external DHCP for WLANs
one WLAN is able to get IP from DHCP server but another WLAN not , the DHCP server is same , only 2 different scopes.
This is debug
*DHCP Socket Task: Feb 05 21:26:43.106: e8:06:88:9b:a8:04 DHCP received op BOOTREQUEST (1) (len 308,vlan 1, port 1, encap 0xec03)
*DHCP Socket Task: Feb 05 21:26:43.106: e8:06:88:9b:a8:04 DHCP processing DHCP
[Code].....
View 2 Replies
View Related
Apr 25, 2012
I have intergrated wlc module in 2800 series cisco router, switch, cisco 1130 lightweight access point, i configured dhcp on router for wireless client, deal is that AP taking ip address from router its ok, but client cannot take dhcp, what im doing wrong? here is configuration of wlc router and switch
wlc configs/
config interface address management 172.16.1.10 255.255.255.0 172.16.1.250
config interface address ap-manager 172.16.1.11 255.255.255.0 172.16.1.250
[Code].....
View 1 Replies
View Related
Oct 31, 2012
Currently we're providing DHCP to wireless clients from a dhcp pool on a cisco 6500. Due to new requirements we need to move to windows 2008 dhcp and when I test this on an unused WLC (7.0.235.0) the client doesn't get an address.
When I do a packet capture on the client I see it requesting dhcp but not getting any response from the server. When I do a dhcp debug on the client I see the same (see attached file).
This seems to me to be a server issue but the same server is supplying addresses to wired clients.
View 3 Replies
View Related
Sep 11, 2011
WAP4410N / configure dhcp OR dhcp CLIENT?
View 3 Replies
View Related
Aug 21, 2012
The wireless client can't get the DHCP address when I enable the On-MAC-Filter-failure, MAC Filtering and Web Auth. Client can get the DHCP address when I only enable the Web Auth in the same WLAN SSID. The WiSM verion is v7.0.235.0. [code]
View 1 Replies
View Related
Aug 31, 2011
User is connecting to 5508, running 7.0.116.0. Previously worked on another AP. TV (client) is set to use dhcp. As other posts have mentioned, "DHCP Addr. Assignment" checkbox is not checked for this wlan, but I also switched it to Required for this wlan but it did not make any difference. Seems to be a problem with just this client as many other clients are on this AP with no problems.
Users have to register their MAC to get on our wireless system, but there is no encyption or security enabled once the device has been registered.
View 34 Replies
View Related
Mar 20, 2013
I have ten E4200 routers deployed in five library branches. In recent months, the E4200's in two branches have occasionally gone into a state where they are not always providing an IP address to both wired and wireless devices. Some devices will get an IP fine and others will not, The problem seems to move and the next day the same device will connect fine and others will not. A reset of the router usually clears the problem but it is becoming more frequent and bothersome. For some reason only two locations are effected.
Some notes:
- Firmware version is 1.0.02 build 13
- When I set devices up with static IP's they work fine, so the problem seems to be related to the DHCP service
- The WAN side of the network tests fine with no issues
- I've had these routers deployed for over a year and this problem just started in the past two months
- Routers and AP's are on different channels to prevent interference
- No nearby WiFi signals appear to be casuing any interference
View 3 Replies
View Related
Mar 29, 2012
I have 2 units Cisco WLC 5508 running software version 7.0.220 with 70 over units Cisco AP 1262N and 1242AG. Some of wireless clients having problem to get the correct IP address from the DHCP server. There are 2 units of Microsoft DHCP. Both DHCP server ip have been configured on the Interface at the WLC. The core switch also being configured with ip helper. I've attached the debug output of one of the wireless client during the problem.
View 12 Replies
View Related
Jun 2, 2012
I just got an EA3500 and I guess I don't understand what "Refresh" does when viewing the DHCP client table under the "Status", "Local Network" tab of the web interface, either that or it's not working. If I have active wired and wireless clients and I power off the EA3500, wait a few minutes, then power it back on, the table is blank. If I hit "Refresh" I would expect it to re-populate the table with the connected clients. For whatever reason, it doesn't. I have to physically disconnect and reconnect the E-net cable, or power cycle the wireless client to get them to reappear in the table. Is something wrong with the router or its s/w
View 9 Replies
View Related
Aug 22, 2012
My EA4500 will periodically clear out the DHCP Client Table and I will lose internet access.This happens once almost every day, normally in the morning. If I can't access the internet I will check the DHCP client table under Status -> Local Network -> DHCP Client Table and it is always empty.After I select Setup -> Reboot it will work again - when I look at the DHCP client table it is now populated with all my devices. I am on firmware version 2.0.37.
View 3 Replies
View Related
Aug 25, 2011
I have purchased E2500 and i am having following problems:
1. DHCP client list not showing - only shows when i reboot the router. After some time, the list never shows even when i press refresh button
2. I can only reserve IP when i reboot the router - after some time i cannot do this action also
I have upgraded to latest firmware and also peformed reset as directed by support.
View 1 Replies
View Related
Oct 29, 2011
I just purchased an E4200 router. I have four clients on my network and they are all set up for DHCP. I renewed their IPs and they all are connected. "Cisco Connect" reports that I have four clients connected. When I access the router and bring up the DHCP Client Table, there are no entries. There should be four entries. Aftern I enable the logging function, none of the logs have any data in them even after I wait for 45 minutes and use the internet and renew IPs. I am using Firmware Version: 1.0.03. I have the same results for both Chrome and Firefox. I want to be able to set Static IPs but I am hampered by the not having any clients in the DHCP client table.
View 9 Replies
View Related
May 20, 2012
I'd like to add a name to a few ip addresses in the DHCP client table currently there is an asterix for a couple client names. the router is an ea3500.
View 2 Replies
View Related
Jun 5, 2012
I have DHCP enabled, but I have assigned a static IP to most of my network devices.When I click on the DHCP Client Table, most of the devices are NOT shown even though I know they are connected and working.One device (a Brother printer) that I have assigned a static IP to actually shows up as having an IP from the DHCP range. A Panasonic TV does not show up at all even though it is connected and woking. I have not been able to assign a static IP to it because it does not show up.
View 3 Replies
View Related
Dec 3, 2012
Region : France
Model : TD-W8968
Hardware Version : V1
Firmware Version : TD-W8968_V1_120926
ISP : SFR
Device in question: siemans C610 IP voip phone
Configuration:
* The C610 is directly connected to TD W8968 via the ethernet port number 3 >> ethernet port number 1 is connected to the devolo homeplug 200AVPLUS . The PC is at the other end of the homeplug network
* The DHCP address starts at 192.168.1.100 - 192.168.1.199.
Symptom:
1. It takes a long time (about 2-3 minutes) for the C610IP to obtain the IP address of 192.168.1.100 after the synchronisation of the ADSL line is finished 2. In the DHCP client list, I could only see the IP address of the PC (192.168.1.101) but not the C610 IP. However, if I type 192.168.1.100, I could access to the configuration page of the C610 IP. - I only managed to see the C610IP once in the DHCP client list.
I tried to unplug -> replug the router but to no avail.
View 2 Replies
View Related
Mar 1, 2011
I have a 6509 with SUP2 w/msfc2 at home, I am currently have dsl for internet with static IP addresses. Due to AT&T not wanting to support faster speeds in my area, I have to look at another option. All of these will be dynamic IP addresses, cable, uverse, etc.
I need to be able to enable dhcp on the wan interface so I can connect directly into one of the gig ports (either on SUP2 or 6316) or on a 10/100 port on a 6348.
I have the following image installed s222-adventerprisek9_wan-mz.122-18.SXF13.bin, according to Cisco's feature tool, it is supported.
I have tried "ip address dhcp" on the interfaces but they will only accept "ip address x.x.x.x", I looked at "ip dhcp" as well and only get the option for "relay".
I would hate to have to put something else in the mix to handle the dhcp portion. I may be keeping the adsl for my mail server traffic and backup in case of an outage on the new provider. So I need to be able to track if a link is up.
View 4 Replies
View Related
