Cisco WAN :: DHCP On WAN Interface 6509
Mar 1, 2011
I have a 6509 with SUP2 w/msfc2 at home, I am currently have dsl for internet with static IP addresses. Due to AT&T not wanting to support faster speeds in my area, I have to look at another option. All of these will be dynamic IP addresses, cable, uverse, etc.
I need to be able to enable dhcp on the wan interface so I can connect directly into one of the gig ports (either on SUP2 or 6316) or on a 10/100 port on a 6348.
I have the following image installed s222-adventerprisek9_wan-mz.122-18.SXF13.bin, according to Cisco's feature tool, it is supported.
I have tried "ip address dhcp" on the interfaces but they will only accept "ip address x.x.x.x", I looked at "ip dhcp" as well and only get the option for "relay".
I would hate to have to put something else in the mix to handle the dhcp portion. I may be keeping the adsl for my mail server traffic and backup in case of an outage on the new provider. So I need to be able to track if a link is up.
View 4 Replies
ADVERTISEMENT
Nov 30, 2011
We are looking to avoid the need to install an additional device in our network as our core 6509s are not being pushed by any stretch. However, we are having an issue getting the 6509 to assign DHCP addresses and perform NAT.
Most interfaces and V LAN's on the 6509 are using public IPs and have BGP routing at the edge. We have a trunk up link coming into the 6509 on a ws-6816 card via a SMF GBIC in slot 9, port 2 that feeds a wifi link where we are looking to provide guest access to our network.
We created 2 V LAN s on the switch 20 and 21. We assigned a private IP and network to the VLAN20 interface and assigned a new public /30 sub net ip to the V LAN 21 interface. The following configuration was applied which I thought was the required configuration based on how we would typically configure ISR routers for the same services...
ip dhcp excluded-address 10.200.200.1
!
ip dhcp pool WiFi_Pool
network 10.200.200.0 255.255.255.0
default-router 10.200.200.1
dns-server 4.2.2.1 4.2.2.2
[ code]...
What am I missing in this configuration? Note that if I create an access switch port for v LAN 20 on the switch and plug a laptop in directly to the 6509, the laptop is unable to receive a DHCP address. If I assign the laptop an address in the 10.200.200.0 /24 range manually, I can ping 10.200.200.1 from the laptop, however, the laptop will not get to the internet as it appears to be failing to perform nat.
View 7 Replies
View Related
Dec 3, 2012
We acquired recentlty a new Cisco 6509 with Sup-2T supervisor card
My question is the following : we have a management subnet on a Copper-based switch; we manage all equipments through this network. I planned to configure the management interface on the 6509 to connect this switch & monitor the VSS through it However, since it is a CMP interface, most of the actions (SNMP, IOS upgrade.. won't be possible through this link) Moreover, I don't think LMS would be able to get the configuration through it (except by configuring a script running "attach" command & show run
Is there something I miss or must I add another interface of the Catalyst to this network (the problem being that I have no copper line card)
View 2 Replies
View Related
May 30, 2012
My AP get IP from 6509, but client cannot get dhcp from my dhcp pool for client, what is the reason?i have 3750g switch with integrated WLC, i connect it to 6509 I did all configs yesterday here is outputs
WLC
Interface Name Port Vlan Id IP Address Type Ap Mgr Guest
-------------------------------- ---- -------- --------------- ------- ------ -----
ap-manager LAG 10 172.16.10.100 Static Yes No
globus LAG 20 172.16.20.254 Dynamic No No
management LAG 10 172.16.10.99 Static No No
service-port N/A N/A 0.0.0.0 Static No No
[code].....
View 8 Replies
View Related
Apr 21, 2013
We have VSS configured between Cat-6509 switches (s72033-advipservicesk9-mz.151-1.SY.bin)..For the voice vlans,dhcp scope is configured within VSS and ip addresses are assigned to ip phones from these pools configured within VSS.Cat 3750 stack is connected with dual links to this vss. IP phones are connected to cat 3750 switches and desktop is connected back to IP phone. For data vlans IP addresses are assigned from external dhcp server.
Currently we are facing lot of ip conflicts for ip phones and after clearing the dhcp conflicts, IP phones starting getting IP addresses..(sufficient IP's do available in the dhcp scope for IP address assignment). (What exactly the role of no ip dhcp conflict logging command......)
View 4 Replies
View Related
Dec 3, 2012
Disable wrr-queue cos-map on 6509 interface?.I have the following config on one of the interfaces that i would like to remove:
[code]...
View 3 Replies
View Related
Nov 20, 2012
I am trying to determine a problem with flapping interface on a router not showing up in log buffer if Cisco IOS. I've included the config on the switch that pertains to the logging and can't seem to figure what is going on. The SNMP trap is being sent to our Central Management trap server and that is reporting the interface flapping but the flap doesn't show up in the log messages.
hstir1#sh int desc | inc 8/33
Gi8/33 up up
hstir1#sh int desc | inc 8/33
Gi8/33 down down
[code].....
View 3 Replies
View Related
Sep 6, 2011
I have just started to discover the power of EEM and am already monitoring config changes on our switches with EEM.I would like to be notified of any interface going up and possibly down. on our 6509's and 3750's This is just to be aware of anyone patching anything in.
View 1 Replies
View Related
Sep 30, 2012
I was wondering if an interface numbering scheme is available for the 6509-E switch equipped with SUP-2T and includes 16Port X 10GE DFC4, 48 x 1GE SFP and RJ 45 line cards. Would like to understand:
How the slots are addressed
Interface Addressing
On board SUP-2T 10G and 1G port addressing
View 2 Replies
View Related
Mar 13, 2013
I have a 10Mbps connection link which I will like to reduce to 5Mbps on a 6509 switch as indicated in the config below. [code] After applying the service policy on the vlan interface, i got this "match vlan is not supported for this interface". I actually tried the rate limit command but I cant see the effect using the speedtest.
View 2 Replies
View Related
Jul 2, 2011
I have attached a pdf of an example of a FWSM configuration with shared interfaces. Now what I dont get is (please refer to the link) url...Is there any difference between the natting that they have done on page B-4 on Context A.as opposed to configuring a static NAT for processing traffic to correct context nat(inside,outside) 209.165.201.0 10.1.2.0.The other question is on page B-2 (diagram) Context A has a customer A network linked to the inside interface. Is it possible to put a default route towards that "Network 2" cloud and restrict traffic from the 6509 switch towards the context A?
View 5 Replies
View Related
Oct 4, 2011
I have problem with traffic coming from GRE interface and going further through FWSM on the same 6509-E chassis.It's very interesting and confusing. If packets are fragmented, I can go through, however, if I use normal packets (usual ping for example) traffic goes from outside to inside and stops on it's way back.
Here is the detailed info:
WS-C6509-E with WS-SUP720-3B
FWSM HW 4.0, SW 4.1(4)
GRE is done in hardware (source is loopback interface - only one loopback per GRE tunnel).
View 5 Replies
View Related
Feb 10, 2011
I have used the following basic configuration to do rate limiting on a vlan interface on a 6509:
access-list 100 permit ip any any
class-map match-all ratelimit
match access-group 100
policy-map ratelimit-10Mb
class ratelimit
police 10000000 428750 conform-action transmit exceed-action drop
[code]....
How do I combine the two correctly to give me a vlan port rate limited at 10Mb up and down, but still setting aside (dynamically) 2Mb for voice?
View 1 Replies
View Related
Mar 14, 2012
We are looking for a solution that to use Sub-interface on a routed port on 6509, instead of using a SVI on it.Are there any different when using Sub-interface?
View 3 Replies
View Related
Jul 10, 2012
I am getting alarms on Solarwind indicating interface down on "GigabitEthernet 4/7 - Gi4/d1" and "GigabitEthernet 4/8 - Gi4/d2" from our core switch 6509.Remote login to the switch does not show the interfaces when I do the "sh run" command. Now I am at site trying to identify and diagnose this fault.Looking at the numbering on the switch, it indicates to me the card where these alarms come from is from the 'intrusion dectection module'
how I may login and identify this interfaces and rectify these alarms.
View 4 Replies
View Related
Jun 8, 2013
How (and is) it possible to rate limit pps on an interface (physical/logical), on a 6509-E?The porpuse is to protect from attacks which lead to very high pps, bypassing traffic rate-limits, and effecting the device's performance
View 2 Replies
View Related
Jun 19, 2009
although cisco sw advisor said that the best IOS for my hardware 6509 Sup720 IOS: (s72033_rp-IPSERVICESK9_WAN-M), Version 12.2(18)SXF16 suits the WiSM; And I tested it already with WiSM version 5.0 but when I've upgraded the WiSM to version 6.0 the service interface from the switch side says:
B5_Noc2_CS1(config)#int gig 4/9
% This interface cannot be modified
as the customer refuse to upgrade the switch IOS & He wants to use the latest ED WiSM sw 6.0;
View 4 Replies
View Related
Aug 8, 2012
i have been facing strange issue on FWSM (6509 switch). we have created a vlan inteface for server farm on fwsm and its stop responding automatically and we need to give shut/ no shut command under that interface to back into normal .
View 11 Replies
View Related
Jan 21, 2013
Platform:
cisco6509-E with FWSM
Supervisor Engine 32 PISA 8GE
sup-bootdisk:s32p3-adventerprisek9_wan-mz.122-18.ZY2.bin
command:
(config)#ip nat inside source static tcp 10.10.8.147 14029 interface g7/8 14029
(config)#no ip nat inside source static tcp 10.10.8.147 14029 interface g7/8 14029
#clear ip nat tran *
(config)#ip nat inside source static tcp 10.10.8.147 14029 interface g7/8 14029
%Port 14029 is being used by system
Or %Static entry in use, cannot change
But when I perform "sh ip nat tran" command,There is nothing
View 1 Replies
View Related
Jan 21, 2013
I configured a Cisco 881 as a vpn-client.When I configure the wan-interface with ip add dhcp , it never gets an IP-address.When I remove the crypto map from the wan-interface , the interface gets an IP-address without any problem.According to examples in the Cisco documentation, I should work; and it works on a 831.
View 3 Replies
View Related
Feb 21, 2010
I have an ASA 5505 configured to get a DHCP'd IP address from the ISP on it's outside interface. The problem I am seeing is when the ISP renews their IP address, the ASA 5505 is still holding on to the old IP address information. I have to either manually renew the IP or reload the ASA. I have the potential of rolling out hundreds of these devices and I would not like my customers to have to reboot their ASA everytime the ISP's DHCP lease experies. I am using an easy vpn autoconnecting to an ASA 5520. Static IP's are not an option on the outside interface of the ASA 5505's.
View 8 Replies
View Related
Mar 14, 2013
on the outside interface i cant perform the command ip address dhcp setroute.I get the error: IP and subnetmask form invalid pair indicating broadcast or network address.The commands are there when I do the ? command. It just will not accept the command with or without dhcp.I am trying to test an ASA-5510 as a 4G failover to our ASA-5520. This is Verizon's solution but they did not provide IPs, they use passthru on the 4G modem so I'm trying to set up dhcp. It worked a few days ago. Not sure what Im missing. The IP I got last time from Verizon was 192.168.0.199.
View 7 Replies
View Related
Nov 15, 2012
I have 1x Cisco 6509 with Sup2 and MSFC2 and it is running on IOS (c6k222-jk9sv-mz.122-17d.SXB11). I have following policy map :
Policy Map VOIP
Class IP PHONE
priority percent 75
and the following command on each interface: service-policy output VOIP those configuration are working fine on SUP2 with MSFC2 but last week I tried to upgrade the SUP2 to SUP32 on the switch and upgrade the IOS to the latest version (s3223-adventerprisek9-mz.122-33.SXJ4) but when I try to put service-policy output VOIP on each physical interface I am getting the following error:
"Priority command is not supported in output direction for this interface" and when I try to add service-policy output VOIP on a V LAN interface I am getting following error:
MQC features are not supported in output direction for this interface. Will I need to change something after upgrading to SUP32..
View 3 Replies
View Related
Nov 21, 2011
I've been running a cisco asa 5505 for quite some time and it has been running fine, now all of a sudden it starts to renew it's outside dhcp adress like every 2 hours. I dont think it's the ISP since I have another device connected also using dhcp to the same ISP and it doesnt renew itself, it's just the ASA. Rebooting it, makes it pick up an adress straight away. The interface seems to be up, the GUI just reports "no ip adress" and then the ASA get's a new IP after about 10-15 min without one. Pressing the renew IP adress button in the GUI throws an error.
View 10 Replies
View Related
Jan 8, 2012
I currently have the managment interface set to my internal network using our DHCP server. We also provide another interface to WLAN for a chartity organization. Their interface and WLAN are locked out of our network (no routes, no nothing) with only VLAN tagging sending out over our backup internet connection. I have been tasked to take over their DHCP scope (255.255.240.0). I added the scope into the 4404 just fine but can't seem to assign it. So, for the sake of argument lets say:
Interface:
management VLAN 10 10.10.10.10 DHCP = 10.10.10.15
charity VLAN 20 192.168.160.2 DHCP = ????
[Code].....
If I tell the charity interface to use 192.168.160.2 for the dhcp scope it errors out. I also tried the DHCP override in the WLAN with no success. If I set either DHCP option for the charity to aim at the managment interface it does nothing as it can't find it..
View 2 Replies
View Related
Dec 27, 2011
I've been using this setting for clients in small offices and what not, and since all they wanted was to give another nutch of security to their network, we've been intalling cisco routers 2600 series still outhere for their internet connections and we had no issues what so ever, not until we run into cable isp provider, and their dhcp wont be able to assign our interface a dynamic IP, this is the setting aplied to the router interface;
interface fastethernet0/0
ip address dhcp
ip nat outside
no ip redirects
no ip unreachables
no ip proxy-arp
Why it wont be seen or assigned an ip by their dhcp, I talked to their isp and they assigned a static ip (private one) and we still have the same issue, if i connect a pix 506e interface with the ip add dhcp assigned to it gets a dynamic ip right away...
View 8 Replies
View Related
Dec 26, 2010
We have a Cisco 886G router connected to the internet. The router receives an ip address. We experience however a problem when the lease time expires. The router does not send a DHCP request to renew it's ip address in time. This causes an interface reset, and connectivity loss, after the lease time of 8 hours.
We are running IOS 880data-universalk9-mz.151-3.T.bin. Config on DHCP receiving interface is:
interface VlanX description To Internet MODEM ip address dhcp ip access-group TEST in!
View 2 Replies
View Related
Apr 21, 2013
i have a adsl modem that is sending dhcp reqeust and i want to use that on my cisco switchs 3560 48 ports.i want to use the interface port 0/48 as a WAN connection and i want to use the other interfaceports for DCHP pool.i have an d-link (dir655) router at home and i want to have the same situation on my cisco switch my WAN interface get from a DHCP reqeust an ip adress from the provider like 10.10.123.44 (for the cisco switch would this interface port gig 0/48)then i want to configere my LAN as a DHCP pool like 192.168.0.1 (for the cisco switch would this interface port gig 0/1 - 47 .
View 3 Replies
View Related
Jul 10, 2012
i have WLC 5508 showing the below Logs , which prevent the users from connecting to the SSIDs , also its disconnecting the associted users DHCP Socket Task: Jul 11 09:54:08.992: %SIM-3-DHCP_SERVER_NO_REPLY: sim_interface.c:1039 Failed to get DHCP response on interface 'interface-02'. Marking interface dirty.*mmListen: Jul 11 09:54:08.638: %MM-3-INVALID_PKT_RECVD: mm_listen.c:7671 Received an invalid packet from 10.21.1.25. Source member:0.0.0.0. source member unknown.it shows 3 to 4 times durring 1 hour ,
View 2 Replies
View Related
Aug 2, 2012
I'm running a system that requires a third (and potentially fourth) DHCP server to be setup on each network in my network. The first two devices are Windows DHCP servers serving IPs from different address ranges for failover. The third DHCP is just a listener to receive OS information and device names to be logged in a database.
Currently this works like a charm for my wired clients as I can add in the third and fourth ip helper-address on each vlan and the information is received by the listeners. However, I cannot find anywhere in my WLC5500 to setup these extra two DHCP helper addresses.
The wireless vlan on my layer 3 switch has all the ip helper-addresses, but this doesn't seem to work, and the devices just use the DHCP servers set on the interface in the WLC.
View 5 Replies
View Related
Jan 22, 2013
I would like to configure the 881G to use both the cellular interface and Fe4 WAN port for internet connectivity.Interface Fe4 is connected to an ADSL router.
I have configure each interface with a default route and weighting:
ip route 0.0.0.0 0.0.0.0 Dialer0 200
ip route 0.0.0.0 0.0.0.0 FastEthernet 4 100
I need to configure Fe4 to get an address as a DHCP client:
interface FastEthernet4
ip address dhcp
no shut
duplex auto
speed auto
How do I remove Fe4 from VLAN1? There is some existing config around VLAN 1:
interface Vlan1
ip address 10.73.0.1 255.255.255.0
ip helper-address 192.168.140.13
ip tcp adjust-mss 1400
no autostate
ip sla 100
icmp-echo 10.64.4.15 source-interface Vlan1
tag 3G Keepalive
frequency 10
Then I guess I need to adjust my Internet-IN ACL to allow broadcasts and UDP 67 and 68?
View 1 Replies
View Related
Feb 26, 2012
I'm trying to find out what is the minimum downtime for a Cisco 2800 series LAN interface configured as DHCP client, in order to initiate a new DHCP discover. How much time does it need to take for the Cisco to "sense" the phy disconnection ?
View 4 Replies
View Related
Feb 25, 2011
I am used to setting up access-lists on outside interfaces with ip addresses that are static. I have recently been given a site that is using a dyndns.org client for name to ip address resolution on an outside interface that is dhcp assigned. I created an access-list to open up ports 41794 and 41795 to an engineering application but everytime I try to connect from the outside I get a syn timeout. The application works when inside the lan. Basically I want to allow outside connections from anywhere on the outside to go to ports 41794 and 41795. I am running a Cisco ASA 5505 on version 7.2(4) Below is my conifg. what I may have misconfigured?
: Saved:ASA Version 7.2(4)!names!interface Vlan1 nameif inside security-level 100 ip address 172.31.2.1 255.255.255.0!interface Vlan2 nameif outside security-level 0 ip address dhcp setroute!interface Ethernet0/0 switchport access vlan 2!interface
[Code].....
View 5 Replies
View Related
