Cisco WAN :: DHCP Server On 3560G
May 23, 2011
I am facing an issue with setting up dhcp server on a 3750G-24PS-S,IOS : c3560-ipbasek9-mz.122-58.SE.bin,the switch configuration is below,interface Vlan100 description ***Data Segment*** ip address 192.168.102.1 255.255.255.0 no shut!ip dhcp excluded-address 198.168.102.1 198.168.102.10! ,ip dhcp pool datalan network 198.168.102.0 255.255.255.0 default-router 198.168.102.1 dns-server 192.168.40.11,!,interface GigabitEthernet0/1 switchport access vlan 100 switchport mode access spanning-tree portfast.
View 2 Replies
ADVERTISEMENT
Dec 4, 2011
I am opening a small branch office in another state and the equipment we purchased is as follows:
ASA5505
3560G.
We'll use a site to site vpn but just in case there's connectivity issues I'd like to use the ASA as DHCP. So far I have a scope defined in the ASA and if I plug a laptop directly in I get an applicable IP address. I trunked the port on the switch that goes to the ASA but not the one on the ASA itself (license restriction) The VLAN that I'm using for my PC's has an ip helper address that is assigned to the inside IP of the ASA.
View 5 Replies
View Related
Nov 13, 2012
Not sure if this is a problem with the switch or the wireless AP connected to the switch, but I have a couple of 3560's, one is a 3560G and the other is a 3560, both have phones and wireless ap's connected to them. The ap's on both of these switches continue to loose there ip address and thus disconnect from the controller. This happens about once a week, but the odd thing is that the phones never loose there ip address. All of my other 3560s and 3560g's that have AP's and phones connected are working fine.
View 2 Replies
View Related
Apr 2, 2013
I've got a Catalyst 3560G, and I want to reset the current index for a DHCP pool. I could remove the leases given for that pool, but I couldn't find this option.
View 3 Replies
View Related
Jan 13, 2013
I have configured DHCP snooping on a WS-3560G-48PS running IOS 12.2(58)SE2 ipservicesk9 variant.When I enable DHCP snooping clients don't get IP addresses, when DHCP snooping is disabled, everything works fine.I have set up a SPAN port and run a capture (attached) on the traffic. Wireshark notes the Seconds elapsed field appeared to be encoded in little-endian but only on some packets. Apart from that, I can see nothing wrong with the DHCP Offer responses from my DHCP server.Attachment config.txt contains the interesting parts of the configuration. Please note g0/32 has been set to ARP inspection trust as without working DHCP snooping it would require a static bind.Is there any way of figuring out which option can't be parsed? Is there a way to force forwarding of unparsable DHCP packets while still running DHCP snooping?
View 3 Replies
View Related
Sep 29, 2011
i am facing the same problem now but am using windows 2003 server
View 1 Replies
View Related
May 6, 2012
[code]...
I am able to obtain IP addresses through the DHCP server for my clients and I am able to browse internet on the server 2k8.Server 2008 - Share Internet through DHCP server
View 10 Replies
View Related
Jan 17, 2013
setting up a DHCP server on a Cisco Layer 3 Switch. How would I set the pool up to issue the lowest available IP address all the time. At the moment it counts up even if a lease has expired.
View 12 Replies
View Related
Jul 9, 2012
anyways here is my concern, we have a DHCP server in our company (HOTEL) and the Computer wont turn on, the computer is Compact Proliant Intel Inside Pentium Pro Processor OS Windows Server 2003, this Computer is so old. they been using this for 12 yrs and they didn't upgrade... now its dead.
since this Computer wont turn on, all of the computers cannot access in the internet, so for the meantime this is what I did... from the modem to router, I configure the router as a STATIC IP and I enter the IP address provided by our Internet Service Provider after that all of the computers form the hotel have internet connection.
now I'm planning to build a new PC and set up a DHCP server but I don't know how and where to start
View 6 Replies
View Related
Feb 20, 2013
I'm trying to enable dhcp server on it. done this how to [URL] It works, but unfortunately the client takes almost 2 min to get an ip.
View 3 Replies
View Related
Sep 14, 2011
I cant to obtain DHCP-address on WAN interface. All over hardware can (windows-based systems and Asus RT-N10), but not Cisco 881 Also i cant to obtain ip even from Asus RT-N10 with this configuration:! version 15.1 service config no service pad service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname Router ! boot-start-marker boot-end-marker ! ! ! no aaa new-model memory-size iomem 10 ip source-route ! ! ip cef no ipv6 cef ! ! crypto pki token default removal timeout 0 ! ! license udi pid CISCO881-K9 sn FCZ1523C3RR ! ! username admin privilege 15 secret 5 $1$0H8v$xx/HtPJIllcFvEWFjzI5t/ ! ! ! ! ! ! interface FastEthernet0 ! interface FastEthernet1 ! interface FastEthernet2 ! interface FastEthernet3 ! interface FastEthernet4 ip address dhcp ip broadcast-address 0.0.0.0 duplex auto speed auto ! interface Vlan1 ip address 192.168.4.1 255.255.255.0 ip broadcast-address 0.0.0.0 ! ip forward-protocol nd no ip http server no ip http secure-server ! ! logging esm config ! ! ! ! ! control-plane ! ! line con 0 exec-timeout 0 0 logging synchronous login local no modem enable line aux 0 line vty 0 4 exec-timeout 0 0 logging synchronous login local transport input all ! end After thousands experiments next configuration started to obtain ip from Asus RT-N10 , but not from ISP ! ! Last configuration change at 12:22:25 UTC Tue Sep 13 2011 by admin ! version 15.1 no service pad service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname Router ! boot-start-marker boot system flash c880data-universalk9-mz.151-3.T.bin boot-end-marker ! ! ! no aaa new-model memory-size iomem 10 ip source-route ! ! ! ip dhcp relay information trust-all ip dhcp compatibility suboption link-selection standard ! ! ip cef no ip dhcp-client broadcast-flag no ipv6 cef ! ! crypto pki token default removal timeout 0 ! ! license udi pid CISCO881-K9 sn FCZ1523C3RR ! ! username admin privilege 15 secret 5 $1$3bFL$y/cxqQLd.8cixPrtETEJ4. ! ! ! ! ! ! interface FastEthernet0 ! interface FastEthernet1 ! interface FastEthernet2 ! interface FastEthernet3 ! interface FastEthernet4 ip dhcp relay information trusted ip dhcp relay information check-reply none no ip dhcp client request tftp-server-address no ip dhcp client request netbios-nameserver no ip dhcp client request vendor-specific no ip dhcp client request static-route ip address dhcp ip broadcast-address 0.0.0.0 duplex auto speed auto ! interface Vlan1 no ip address ip broadcast-address 0.0.0.0 ! ip forward-protocol nd no ip http server no ip http secure-server ! ! logging esm config ! ! ! ! ! control-plane ! ! line con 0 exec-timeout 0 0 logging synchronous login local no modem enable line aux 0 line vty 0 4 exec-timeout 0 0 logging synchronous login local transport input all ! end ISP's hardware based on Juniper.What else must I switch of/on to start DHCP-client?!
View 5 Replies
View Related
Aug 16, 2012
OLD Dell computer running Windows XP Professional. Just ran a clean install and installed new drivers yesterday. After installing Service Pack 2, I began getting limited connectivity errors. Tried ipconfig/release and ipconfig/renew, but received the DHCP error.
View 6 Replies
View Related
Jan 26, 2013
How to configure DHCP server if i have 2 vlans. I know how to configure rest of the network, just i don't know server.I use packet tracer and i attached file with my network. PC1 is on VLAN1 and PC2 is on VLAN2.I want ip addresses in vlan1 to be from 192.168.1.2 and in vlan2 from 192.168.2.2. I would like to do it just like in the designed network, without router.
View 5 Replies
View Related
Oct 19, 2012
Can I have two asa firewall between dhcp client and dhcp server. if yes what solution i have to have to get dhcp leases. should i have to configure dhcp relay on both the asa.
View 5 Replies
View Related
Dec 26, 2012
know any plan from Cisco to make 300 series switch to work as a DHCP server?
View 1 Replies
View Related
Aug 16, 2011
I have a WCS that I use to manage 8 controllers (2 WiSM's totaling 4 controllers, and 4 more controllers at remote locations). All controllers connect to 3750 switches. The layer three interfaces for all V LAN's that are related to the wireless network are created on these switches. Each layer three interface has a helper address that points the devices in the sub net to the correct DHCP server.
When a wireless device requests a DHCP request I believe it gets to that server based on the relay from the layer three interface on the 3750. However, I know that the virtual interface on the controller is also requesting an address because my firewall is flooded with deny statements. The virtual interface is configured for 1.1.1.1 and so it gets blocked. I am starting to question the use of this interface considering the fact that it is getting blocked and the clients are still getting address.
Are both interfaces trying to act as DHCP relays? Could I setup the controllers to be the only relay (without using the virtual interface)?
View 3 Replies
View Related
Dec 13, 2010
Can we Configure DHCP server in 3750 ? we have configure DHCP server in 1841 router but some reason we want remove router .
View 2 Replies
View Related
May 21, 2013
I have a 2504 WLC and 1042 ap's. Everything worked great in my test enviroment (of course). Now when I want to deploy the wireless, the ap's are not getting and ip for the windows dhcp server.
I have option 43 configured in dhcp, sub option 241>ip address of the controller
I have my A record in dns, cisco-capwap-controller.
*Mar 1 00:03:17.050: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
Not in Bound state.
*Mar 1 00:03:27.050: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:03:27.054: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
*Mar 1 00:03:37.054: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:03:47.054: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:03:57.054: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:04:07.054: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
Not in Bound state.
View 3 Replies
View Related
Oct 18, 2007
I am working to test the PPPoE solution. The requirement is that she like to have a PPPoE server (7200), enable the DHCP pool on the router. The PPPoE client (1811) should receive the IP address through the DHCP and with subnet mask (/24) so that routing protocol can enable between the PPPoE server and client.We test with some initial configuration but not success to obtain DHCP address from the pool.
On PPPoE server router,
!
ip dhcp pool DHCP-PPP
network 192.168.254.0 255.255.255.0
default-router 192.168.254.254
[Code]...
View 2 Replies
View Related
Apr 14, 2011
2 dhcp server on the same lan segment not thesame ip add series , how can i prevent to lease ip from another ip series
View 2 Replies
View Related
Oct 30, 2011
I've made hotspot ad hoc and then my client try to connect my hotspot but it must setting manually...how to my client connect to my hotspot automatically not manually??? and how to install and setup dhcp server i windows 7...
View 6 Replies
View Related
Apr 28, 2011
when we use switch as dhcp server and we want to configure a DHCP relay on other subnet that is not connected to this switch, what is the DHCP server ip address for configuration of DHCP relay? Should we use vlan1 ip?
View 2 Replies
View Related
Aug 23, 2011
A Windows Server 2008 r2 with 2 internet ports. One (IP: 10.0.96.132) connected to company intranet and one (192.168.10.1) as DHCP server connect to several PCs (192.168.10.**) through a switch.The problem is the PCs (192.168.10.**) can ping the DHCP server (192.168.10.1) , while DHCP server (192.168.10.1) can not ping (192.168.10.**).How to configure the server so that all these PCs can access the intranet?
View 4 Replies
View Related
Nov 2, 2011
I've been trying (in vain) to connect a USB Wireless device to be able to use it off my wireless network. I have (2) other laptops and (1) other desktop connecting to the router with no issues. For some reason, this old desktop keeps installing an Ethernet device (probably on the MB) and is automatically Configuring the IP address to that instead of the USB wireless device.I've tried uninstalling the Ethernet device but it comes right back after I do a reboot. Even when I disable it, I still can not connect with my Wireless device.
View 14 Replies
View Related
Feb 22, 2011
i want to setup DHCP using my windows xp
View 1 Replies
View Related
Nov 17, 2011
i did just had a rogue anti-virus infection i did a removal of it AV Security 2012
View 1 Replies
View Related
Apr 17, 2012
My Windows xp computer can't connect to the DHCP server correctly and thus can't connect to the internet. It is connected through an Ethernet cable to a wireless router. All other computers on the same network connect fine to the router, both wired and wireless.This all started after I left my computer alone for a few hours and came back with it not coming out of idle. After shutting it off and turning it back on, it would not connect to the DHCP server.It assigned me the autoconfig address 169.254.189.73 because it couldn't connect to the DHCP server. I even tried a static IP but even that wouldn't fix it. I have tried the same ethernet cable in another computer and it worked fine so I know that it is because of my computer.I have tried renewing and releasing the connection using ipconfig in the command prompt but that did nothing. The settings are all the same as the other computers running through the same router. I have tried shutting down all the other computers and reconnecting the trouble one but again still nothing.The last thing I'm not sure about is the network adapter driver. I have reinstalled it but I'm not sure if the driver is correct. I have an NVIDEA nforce 10/100 Mbps Ethernet adapter. I attempted to reinstall but I'm not sure I selected the correct generation when I downloaded the driver installer. My computer says nothing about the generation of the adapter so I just chose the newest generation. My adapter is integrated in the motherboard.
View 19 Replies
View Related
May 7, 2011
I have a machine with Windows Server 2003 running an Exchange Server in a office with 5 workstations attached. The server is being used for a basic outlook calendar across the various workstations, nothing major. Our current ISP provides us with a Static IP address. The party that installed and configured the server set it up to run the DHCP server on the server PC itself. As in, the machine running windows server is also running a software DHCP server for the entire network. THE SETUP: As of right now we have a wall port (internet access) with a cable running to a 8 port unmanaged netgear switch that has cables hooked up to the 5 workstations as well as the server itself. Pretty simple.THE QUESTION: How do I configure the ISP static settings on the DHCP Server portion of the Server PC? We may be getting a new ISP with a dynamic address OR a new static address. WHAT I'VE TRIED: I've tried configuring the IP address on the Server PC the way I would via the NIC adapter settings but it already has a internal IP address from the DHCP Server running on that PC so changing that was no good.
View 2 Replies
View Related
Jul 25, 2012
How to get the details of an android phone connected to the wifi network.Even I know the IP of the device as we can see it from the phone it self how to fetch some information about the phone like its os version (2.2.x Froyo,2.3.x Gingerbread etc ),Model of phone etc.My aim is to identify an android when IP is given to me.I got some tool likeQuote:nmap,but it is not showing a full details of phone by which I can recognise it is as an android phone,is there any other tool or mechanism to identify the phone if the IP is givenI got something like "vendor class " of the dhcp protocol stack ,but how to read this data
View 1 Replies
View Related
Apr 5, 2011
I'm using 2003 server for DHCP settings. I don't want some computers to get ip address automatically but if they put manually ip address, it's ok, they can connect.How it can be done?I mean when those computers try to connect for wireless, they should not get any ip address (so internet) until they put manually ip address, default gateway and dns server.
View 3 Replies
View Related
Oct 24, 2012
I recently reset my Quidway WA1003A modem from Huawei and ever since, the radio button for the server settings under DHCP configuration is at OFF whenever I start up my computer. So if I try accessing the internet via wi-fi on my phone, I'll have to manually change the radio button by opening up 192.168.1.1 through the browser on my computer each time. I never faced this issue prior to the reset. It used to somehow always be saved as ON.
View 2 Replies
View Related
Aug 22, 2011
I'm totally new to using Windows Server 2003 (or any windows server edition) but I do have a basic understand of networking. I have a machine with Windows Server 2003 running an Exchange Server in a office with 5 workstations attached. The server is being used for a basic outlook calendar across the various workstations, nothing major. Our current ISP provides us with a Static IP address. The party that installed and configured the server set it up to run the DHCP server on the server PC itself. As in, the machine running windows server is also running a software DHCP server for the entire network. As of right now we have a wall port (internet access) with a cable running to a 8 port unmanaged netgear switch that has cables hooked up to the 5 workstations as well as the server itself. How do I configure the ISP static settings on the DHCP Server portion of the Server PC? We may be getting a new ISP with a dynamic address OR a new static address.
I've tried configuring the IP address on the Server PC the way I would via the NIC adapter settings but it already has a internal IP address from the DHCP Server running on that PC so changing that was no good. I guess what I'm basically looking for is a screen like this (I hope you're familiar with the configuration pages of Linksys Routers) url...
View 14 Replies
View Related
Aug 21, 2012
so i want to move my dns and dhcp to a server (sbs2011). i am currently using a netgear 3700. i am a little confused on how to set this up. i know to turn off dhcp on the router. will the server give out a dns address? do i even need to router, or could i just use a switch?
View 1 Replies
View Related
