Cisco WAN :: PPPoE Server With DHCP 1811
Oct 18, 2007
I am working to test the PPPoE solution. The requirement is that she like to have a PPPoE server (7200), enable the DHCP pool on the router. The PPPoE client (1811) should receive the IP address through the DHCP and with subnet mask (/24) so that routing protocol can enable between the PPPoE server and client.We test with some initial configuration but not success to obtain DHCP address from the pool.
On PPPoE server router,
!
ip dhcp pool DHCP-PPP
network 192.168.254.0 255.255.255.0
default-router 192.168.254.254
[Code]...
View 2 Replies
ADVERTISEMENT
Apr 26, 2011
I have an 1811 configured with dhcp scope and generally it works correctly. I have a host on the vlan/subnet that the scope is assigned that can receive an IP and all the specifics from the dhcp server. [code]
The host on the vlan/subnet should use the router as the dns server to resolve static hosts that are configured on the router itself. Can an IOS DHCP/DNS server do this?
View 1 Replies
View Related
Nov 20, 2011
I have two DIR-615 devices, I want use first device for main AP and DHCP server and PPPoE . And use second device for Repeater.
How to work WPS and Push button on this device.
View 6 Replies
View Related
Jul 4, 2012
PPPoE connection isn't established...Config Cisco 1811 (c181x-advipservicesk9-mz.124-15.T15.bin):
...
vpdn enable
...
vpdn-group 1
request-dialin
protocol pppoe
[code].....
View 7 Replies
View Related
Aug 29, 2011
Trying to find a way to configure my 851 for home use. My internet provider use PPPoE with PAP and althrough I found many configuration options they all are incomplete...or i cant find the logic behind those commands. First of all I need to say what I need:
1. Configurate my int Fa4 (WAN) with pppoe so when i insert my ISP cable in it it will negotiate and take IP.
2. Configurate DHCP on LAN (Fa0-3) so that when I insert my PC it will take a fake IP.
Here is the place where i found some conf examples: [URL] and I have some questions:
1. MTU - Should I use the 1492 value or the "pppoe-client ppp-max-payload 1500"?
2. ip route 10.10.25.2 255.255.255.255 dialer 0 - How can i set an IP route when my connexion informations only come after i connect? (Because is PPPoE)?
3. I cant configurate the DHCP because I dont know the default route, I dont know the DNS, and i dont know the default gateway because I dont know them due to PPPoE !
View 20 Replies
View Related
May 15, 2012
I've heard that you can configure an 1811 router as a terminal server for remote console work.I have several of them in the lab and would love to try it out.
View 2 Replies
View Related
Jan 25, 2011
I've been having this issue for about 3 months now, off and on, never seemed to be predictable but started happening more and more, which prompted me to look into it.
Currently, the DSL Modem is configured in bridge mode with the ASA handling PPPoE. The WAN address is being assigned via DHCP. The ASA is running 8.2(1). The WAN interface will drop it's DHCP lease and will not renew it without power cycling the DSL modem. I did a little bit of googling and found mention of setting "dhcp-client client-id interface outside", specifically this was an issue pre 7.2(22), but doesn't seem to affect my situation. Originally, I had the MTU on the outside interface configured as 1500, changing it to 1492 has not resolved my issue either.
I've enabled PPPoE and DHCPC debugging and posted the results below when the event occurs, I'm thinking this is moreso a PPPoE issue than it is a DHCP/DHCP Lease issue as I am not seeing any debug messages from DHCPC.
Code...
View 1 Replies
View Related
Sep 25, 2011
I have a ZyXel P-660R-D1 DSL modem, and lately I've been experiencing random outages. I'm not super knowledgeable when it comes to the technical side of networking, but I know enough to look around the modems GUI and recognize when something isn't right. I'm pretty sure this is not a problem on my end, but I'd like to hear a few other peoples opinions. Basically I have four lights on the modem: Power, Ethernet, DSL, and Internet. DSL is the light that indicates connection to the PPPoE server, and lately it will just randomly drop. I've never experienced problems connecting with the PPPoE server until just recently. Every once in a while my Internet light will drop, and a simple reset will take care of it, but rarely am I ever not connected to the PPPoE server. One day it was down for three or so hours, one day for nine, another day it cut in and out for about four hours, and today was another nine hour day. how it works is that my username and password are verified through the ISPs PPPoE server, and then I am granted access to the web. I'm lead to believe that it's nothing on my end because all troubleshooting methods fail, it just randomly fixes itself several hours later. The first nine hour stretch I experienced I thought may have been because of maintenance or some other unforeseen circumstance, but it has happened a few times now so I'm not too sure. My provider, Earthlink, hasn't listed any 'Known Outages' on their site, but then again they never do.
View 1 Replies
View Related
Mar 27, 2012
I´m trying to configure SR520 Cisco router as PPPoE server. The point is, when configuration is done and PPPoE client is directly connected to the interface, SR520 doesn´t respond to incoming PADI. PADI is not shown in PPPoE debugs (debug pppoe events, packets and errors).On the other hand, I get the PADI capturing packets with wireshark (so PADI is being sent) and the same configuration on other router works fine.
View 2 Replies
View Related
Dec 24, 2010
There is one router ( SWR54BGA ), wan interface functional ( connected as a dhcp client to the lan interface of another router , packets are forwarded). When i connect the wan interface to the isp line, and provide the pppoe login details ,it won't work. When i try to connect manually to the pppoe server from the wan configuration page, after about 30 sec i get the connection failed message.Is the firmware corrupt, should i go the ddwrt route?
View 2 Replies
View Related
Feb 11, 2013
I'm planning to deploy PPPoE Server (Cisco Router 7609) for an ISP. This ISP will provide Internet connection for customer over Ethernet (QinQ VLAN).I have to provide a solution to assign bandwidth to each customer by RADIUS. I found some documents about this function but they said that it could work with PPPoA or PPPoE over ATM only. So which method I shoud deploy to get this goal?
View 1 Replies
View Related
Feb 22, 2011
I'm planning to deploy PPPoE Server (Cisco Router 7609) for an ISP. This ISP will provide Internet connection for customer over Ethernet (QinQ VLAN).I have to provide a solution to assign bandwidth to each customer by RADIUS. I found some documents about this function but they said that it could work with PPPoA or PPPoE over ATM only. So which method I shoud deploy to get this goal?
View 1 Replies
View Related
Sep 19, 2010
I installed a Linksys WRT54G2 router earlier this year and set my Siemens modem from AT&T(Actually from SBC before the two merged) in bridge mode. I did this so I could change the NAT setting on our internet, which was interfering with my Xbox. It worked for about 4 or 5 months with little to no problems. Recently, however, the internet has been disconnecting and when I check the status page on the router it says it is disconnected. Sometimes clicking on the connect button will work, but usually it will say "Connecting" and keep refreshing the page for a little while without any change, then give me a message saying it couldn't get the IP from the PPPoe server. Turning it and the Siemens modem on and off and fiddling around seems to solve the problem, but only temporarily. Interestingly enough, I don't think it ever interferes with my Xbox. Until recently, the Xbox was set as the highest priority on the QoS page, but I changed the computer to the highest priority and it hasn't worked. In addition, the small, thin green light bar just below the Linksys logo on the top of the router has just recently started changing to orange occasionally
View 9 Replies
View Related
Nov 17, 2012
I have a Linksys WRT310N V1.I am trying to connect this via PPPoE to another Thompson router/modem that has been succesfully switched into BRIDGE mode.The Linksys router is conneted via ethernet cable to an ehternet port on the Thompson router.The ADSL cable is pluggedinto the WAN port of the Thomson 'bridge'.There is no cable in the WAN port of the Linksys router.
The Linksys router is set up to connect over PPPoE using the username and password that was given to me by my ISPs tech support (checked and double checked).The DHCP server on the Bridged Thomson is set to ON. DNS is set to OFF.the DHCP server on the Linksys router is set to ON.
View 2 Replies
View Related
Jul 22, 2011
I recently bought an E3000. I am trying to setup a wireless home network.Google and tried a lotta things (power cycle the most no. of times ). Nothing worked.So I poked around. Looked up the IPConfig of my PC with wire connected directly(no router), was 192.168.0.xxx. So I hit 192.168.0.1 in my browser address bar, and it came up with the login page for a D-Link DIR600. A wireless router with wireless disabled. Apparently this is being used as a switch by my ISP. This I know cause I checked the active connections and DHCP reservations on the D link and it showed up about 100 different PC's (including MAC and IP addresses).
View 9 Replies
View Related
May 23, 2011
We have WLC-4402 and LWAP-1510, we have issue when users trying to connect to pppoe server with pppoe connection from wireless network. On LAN, pppoe connection work properly and everything is normal. Also I enable broadcast fowarding on GUI but he problem still exist.
View 1 Replies
View Related
Sep 20, 2012
I have been working on this for hours and getting frustrated! This router has been set up for over a year with no trouble, but recently had trouble connecting with my wireless devices and was kicking my wired (ethernet) laptop off when it is usually on all the time.
Now, my wired connection works through the router, the wireless devices all connect to the network but do not have access to theinternet. From the router's setup page, when I enter my PPPoE information and go to status and connect, it tries to connect a few times then gives me the error message 'cannot get IP address from PPPoE server"
I have tried updating firmware, resetting, restarting, recycling power, chat support with ISP and chat support with Linksys. Have verified my username and key and those are correct otherwise I'd have no internet access at all. I do have wired access but not wireless. The wired connection does go through the router.
Bridging - my modem is a bridging modem only, so it shouldn't be that.
View 4 Replies
View Related
Dec 22, 2012
I look forward to the new firmware can improve this problem.
View 3 Replies
View Related
Sep 29, 2011
i am facing the same problem now but am using windows 2003 server
View 1 Replies
View Related
May 6, 2012
[code]...
I am able to obtain IP addresses through the DHCP server for my clients and I am able to browse internet on the server 2k8.Server 2008 - Share Internet through DHCP server
View 10 Replies
View Related
Jan 17, 2013
setting up a DHCP server on a Cisco Layer 3 Switch. How would I set the pool up to issue the lowest available IP address all the time. At the moment it counts up even if a lease has expired.
View 12 Replies
View Related
Jul 9, 2012
anyways here is my concern, we have a DHCP server in our company (HOTEL) and the Computer wont turn on, the computer is Compact Proliant Intel Inside Pentium Pro Processor OS Windows Server 2003, this Computer is so old. they been using this for 12 yrs and they didn't upgrade... now its dead.
since this Computer wont turn on, all of the computers cannot access in the internet, so for the meantime this is what I did... from the modem to router, I configure the router as a STATIC IP and I enter the IP address provided by our Internet Service Provider after that all of the computers form the hotel have internet connection.
now I'm planning to build a new PC and set up a DHCP server but I don't know how and where to start
View 6 Replies
View Related
Feb 20, 2013
I'm trying to enable dhcp server on it. done this how to [URL] It works, but unfortunately the client takes almost 2 min to get an ip.
View 3 Replies
View Related
Sep 14, 2011
I cant to obtain DHCP-address on WAN interface. All over hardware can (windows-based systems and Asus RT-N10), but not Cisco 881 Also i cant to obtain ip even from Asus RT-N10 with this configuration:! version 15.1 service config no service pad service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname Router ! boot-start-marker boot-end-marker ! ! ! no aaa new-model memory-size iomem 10 ip source-route ! ! ip cef no ipv6 cef ! ! crypto pki token default removal timeout 0 ! ! license udi pid CISCO881-K9 sn FCZ1523C3RR ! ! username admin privilege 15 secret 5 $1$0H8v$xx/HtPJIllcFvEWFjzI5t/ ! ! ! ! ! ! interface FastEthernet0 ! interface FastEthernet1 ! interface FastEthernet2 ! interface FastEthernet3 ! interface FastEthernet4 ip address dhcp ip broadcast-address 0.0.0.0 duplex auto speed auto ! interface Vlan1 ip address 192.168.4.1 255.255.255.0 ip broadcast-address 0.0.0.0 ! ip forward-protocol nd no ip http server no ip http secure-server ! ! logging esm config ! ! ! ! ! control-plane ! ! line con 0 exec-timeout 0 0 logging synchronous login local no modem enable line aux 0 line vty 0 4 exec-timeout 0 0 logging synchronous login local transport input all ! end After thousands experiments next configuration started to obtain ip from Asus RT-N10 , but not from ISP ! ! Last configuration change at 12:22:25 UTC Tue Sep 13 2011 by admin ! version 15.1 no service pad service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname Router ! boot-start-marker boot system flash c880data-universalk9-mz.151-3.T.bin boot-end-marker ! ! ! no aaa new-model memory-size iomem 10 ip source-route ! ! ! ip dhcp relay information trust-all ip dhcp compatibility suboption link-selection standard ! ! ip cef no ip dhcp-client broadcast-flag no ipv6 cef ! ! crypto pki token default removal timeout 0 ! ! license udi pid CISCO881-K9 sn FCZ1523C3RR ! ! username admin privilege 15 secret 5 $1$3bFL$y/cxqQLd.8cixPrtETEJ4. ! ! ! ! ! ! interface FastEthernet0 ! interface FastEthernet1 ! interface FastEthernet2 ! interface FastEthernet3 ! interface FastEthernet4 ip dhcp relay information trusted ip dhcp relay information check-reply none no ip dhcp client request tftp-server-address no ip dhcp client request netbios-nameserver no ip dhcp client request vendor-specific no ip dhcp client request static-route ip address dhcp ip broadcast-address 0.0.0.0 duplex auto speed auto ! interface Vlan1 no ip address ip broadcast-address 0.0.0.0 ! ip forward-protocol nd no ip http server no ip http secure-server ! ! logging esm config ! ! ! ! ! control-plane ! ! line con 0 exec-timeout 0 0 logging synchronous login local no modem enable line aux 0 line vty 0 4 exec-timeout 0 0 logging synchronous login local transport input all ! end ISP's hardware based on Juniper.What else must I switch of/on to start DHCP-client?!
View 5 Replies
View Related
May 23, 2011
I am facing an issue with setting up dhcp server on a 3750G-24PS-S,IOS : c3560-ipbasek9-mz.122-58.SE.bin,the switch configuration is below,interface Vlan100 description ***Data Segment*** ip address 192.168.102.1 255.255.255.0 no shut!ip dhcp excluded-address 198.168.102.1 198.168.102.10! ,ip dhcp pool datalan network 198.168.102.0 255.255.255.0 default-router 198.168.102.1 dns-server 192.168.40.11,!,interface GigabitEthernet0/1 switchport access vlan 100 switchport mode access spanning-tree portfast.
View 2 Replies
View Related
Aug 16, 2012
OLD Dell computer running Windows XP Professional. Just ran a clean install and installed new drivers yesterday. After installing Service Pack 2, I began getting limited connectivity errors. Tried ipconfig/release and ipconfig/renew, but received the DHCP error.
View 6 Replies
View Related
Jan 26, 2013
How to configure DHCP server if i have 2 vlans. I know how to configure rest of the network, just i don't know server.I use packet tracer and i attached file with my network. PC1 is on VLAN1 and PC2 is on VLAN2.I want ip addresses in vlan1 to be from 192.168.1.2 and in vlan2 from 192.168.2.2. I would like to do it just like in the designed network, without router.
View 5 Replies
View Related
Oct 19, 2012
Can I have two asa firewall between dhcp client and dhcp server. if yes what solution i have to have to get dhcp leases. should i have to configure dhcp relay on both the asa.
View 5 Replies
View Related
Dec 26, 2012
know any plan from Cisco to make 300 series switch to work as a DHCP server?
View 1 Replies
View Related
Aug 16, 2011
I have a WCS that I use to manage 8 controllers (2 WiSM's totaling 4 controllers, and 4 more controllers at remote locations). All controllers connect to 3750 switches. The layer three interfaces for all V LAN's that are related to the wireless network are created on these switches. Each layer three interface has a helper address that points the devices in the sub net to the correct DHCP server.
When a wireless device requests a DHCP request I believe it gets to that server based on the relay from the layer three interface on the 3750. However, I know that the virtual interface on the controller is also requesting an address because my firewall is flooded with deny statements. The virtual interface is configured for 1.1.1.1 and so it gets blocked. I am starting to question the use of this interface considering the fact that it is getting blocked and the clients are still getting address.
Are both interfaces trying to act as DHCP relays? Could I setup the controllers to be the only relay (without using the virtual interface)?
View 3 Replies
View Related
Dec 13, 2010
Can we Configure DHCP server in 3750 ? we have configure DHCP server in 1841 router but some reason we want remove router .
View 2 Replies
View Related
May 21, 2013
I have a 2504 WLC and 1042 ap's. Everything worked great in my test enviroment (of course). Now when I want to deploy the wireless, the ap's are not getting and ip for the windows dhcp server.
I have option 43 configured in dhcp, sub option 241>ip address of the controller
I have my A record in dns, cisco-capwap-controller.
*Mar 1 00:03:17.050: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
Not in Bound state.
*Mar 1 00:03:27.050: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:03:27.054: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
*Mar 1 00:03:37.054: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:03:47.054: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:03:57.054: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:04:07.054: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
Not in Bound state.
View 3 Replies
View Related
Apr 14, 2011
2 dhcp server on the same lan segment not thesame ip add series , how can i prevent to lease ip from another ip series
View 2 Replies
View Related
