Linksys Wireless Router :: EA4500 - Not Custom DNS Server Using PPPoE?

Dec 22, 2012

I look forward to the new firmware can improve this problem.

View 3 Replies


ADVERTISEMENT

Linksys Wireless Router :: EA4500 Won't Connect Through PPPoE

Nov 17, 2012

I've been using my EA4500 since it's original launch date as a PPPoE router through another router/modem which is the Netgear DG834G V4 set to Modem Only mode which was working fine for a long time!A month ago, a friend wanted to borrow the Netgear Router and after he gave it back I reset it like I always do and entered my settings in router mode(i.e. username and password) to check if I havewe working Internet connection and that the router is working properly and it was working properly like it was before I lent it. Now comes the problem, if I keep using the Netgear router as the PPPoE handler and make the EA4500 work as "Automatic Configuration DHCP" it works flawlessly but if I set the Netgear router to modem mode and make the EA4500 handle the PPPoE connection, the report in the troubleshooting tab keeps on saying "Connecting" endlessly!
 
Note: I've replicatedthe settings that I used on both router before and after lending it to my friend so there's no difference in settings!

View 6 Replies View Related

Linksys Wireless Router :: WRT54G2 Can't Get IP From PPPoE Server

Sep 19, 2010

I installed a Linksys WRT54G2 router earlier this year and set my Siemens modem from AT&T(Actually from SBC before the two merged) in bridge mode.  I did this so I could change the NAT setting on our internet, which was interfering with my Xbox.  It worked for about 4 or 5 months with little to no problems.  Recently, however, the internet has been disconnecting and when I check the status page on the router it says it is disconnected.  Sometimes clicking on the connect button will work, but usually it will say "Connecting" and keep refreshing the page for a little while without any change, then give me a message saying it couldn't get the IP from the PPPoe server.  Turning it and the Siemens modem on and off and fiddling around seems to solve the problem, but only temporarily.  Interestingly enough, I don't think it ever interferes with my Xbox.  Until recently, the Xbox was set as the highest priority on the QoS page, but I changed the computer to the highest priority and it hasn't worked.  In addition, the small, thin green light bar just below the Linksys logo on the top of the router has just recently started changing to orange occasionally

View 9 Replies View Related

Linksys Wireless Router :: WRT310N V1 Cannot Get An IP From PPPoE Server

Nov 17, 2012

I have a Linksys WRT310N V1.I am trying to connect this via PPPoE to another Thompson router/modem that has been succesfully switched into BRIDGE mode.The Linksys router is conneted via ethernet cable to an ehternet port on the Thompson router.The ADSL cable is pluggedinto the WAN port of the  Thomson 'bridge'.There is no cable in the WAN port of the Linksys router.
 
The Linksys router is set up to connect over PPPoE using the username and password that was given to me by my ISPs tech support (checked and double checked).The DHCP server on the Bridged Thomson is set to ON. DNS is set to OFF.the DHCP server on the Linksys router is set to ON.

View 2 Replies View Related

Linksys Wireless Router :: E3000 - Way Of Getting IP From Pppoe Server?

Jul 22, 2011

I recently bought an E3000. I am trying to setup a wireless home network.Google and tried a lotta things (power cycle the most no. of times ). Nothing worked.So I poked around. Looked up the IPConfig of my PC with wire connected directly(no router), was 192.168.0.xxx. So I hit 192.168.0.1 in my browser address bar, and it came up with the login page for a D-Link DIR600. A wireless router with wireless disabled. Apparently this is being used as a switch by my ISP. This I know cause I checked the active connections and DHCP reservations on the D link and it showed up about 100 different PC's (including MAC and IP addresses).

View 9 Replies View Related

Linksys Wireless Router :: WRT54G2 - Cannot Get IP Address From PPPoE Server

Sep 20, 2012

I have been working on this for hours and getting frustrated!   This router has been set up for over a year with no trouble, but recently had trouble connecting with my wireless devices and was kicking my wired (ethernet) laptop off when it is usually on all the time.
 
Now,  my wired connection works through the router, the wireless devices all connect to the network but do not have access to theinternet.    From the router's setup page, when I enter my PPPoE information and go to status and connect, it tries to connect a few times then gives me the error message 'cannot get IP address from PPPoE server"
 
I have tried updating firmware, resetting, restarting, recycling power, chat support with ISP and chat support with Linksys.   Have verified my username and key and those are correct otherwise I'd have no internet access at all.  I do have wired access but not wireless.   The wired connection does go through the router.
 
Bridging - my modem is a bridging modem only, so it shouldn't be that.

View 4 Replies View Related

Linksys Wireless Router :: FTP Server On EA4500?

May 11, 2012

Using the FTP server built into the EA4500 firmware. I can get the FTP service to work from some computers outside my home network, but when i try to access the service from a PC within my home network i am unable to connect to the server through the WAN address.

View 1 Replies View Related

Linksys Wireless Router :: Media Server On EA4500

May 15, 2012

I just setup the Linksys EA4500 router on my computer and I am able to hook up to the internet on my computer and on my Logitech Revue.  How do I access the media server?  It is not showing up on the Logitech Revue or my Samsung TV

View 9 Replies View Related

Linksys Wireless Router :: EA4500 FTP Server Name Did Not Update With New SSID

Nov 30, 2012

I had a SSID name conflict with one of my devices and the router. I changed the routers SSID which eliminated the conflict.  I noted that after changing the SSID, the name of the FTP server did not update to the new SSID. Is this an issue? I did not see any way to manually edit the FTP name. FTP works fine as is.

View 1 Replies View Related

Linksys Wireless Router :: EA4500 Blocking 1 Server Address?

Apr 10, 2013

My router,EA4500 is blocking just one I.P address,(a game server), and I am unable to connect to the server. I have tried this on 2 different computers, reinstalled the Cisco Connect software, reset to factory defaults and it is still blocking me from getting on this server. When I by pass the router and plug directly into my modem the Server shows up fine and I am able to get on but when I put the Router back it blocks it and does not show up at all.

View 1 Replies View Related

Linksys Wireless Router :: To Get Playlists On EA4500 Media Server

Aug 25, 2012

How to get playists to work on the EA4500 Media Server? I have the Music folder share working with a Roku Soundbridge, so now would like to copy my iTunes playlists to this folder as well. I've tried creating a .m3u file in the Music folder but the Soundbridge doesn't recognize it. I put the following one line in this file, which just points to the file stored on the disk connected to the EA4500.

View 1 Replies View Related

Linksys Wireless Router :: EA4500 DLNA Certified Media Server

Aug 1, 2012

I'm very disappointed with this EA4500 DLNA feature this is one of the main reasons why i got this router.My Sammy TV can detect the USB that is attached and is able to view the files in the drive but when you play any video file larger than 1gb it does not work even shuts down my TV.Only on smaller files does it work flawlessly I know its not the TV because I have played those files on my previous Router (Netgear WNDR3800)  and they even work when i connect the hard drive directly to the TV has any one else had this issue happen to them?

View 9 Replies View Related

Linksys Wireless Router :: EA4500 DLNA Server Not Working With Movies

May 28, 2012

I am trying to stream movies and music to my Panasonic TV.  I have a USB hard drive connected to the EA4500.
 
The TV sees the media on the device and music plays fine.  However, every movie I've tried shows up with an exclamation point and when I try to play it I get a message to the effect that "unable to open media".  Is the EA4500 media server only compatible with certain movies?

View 9 Replies View Related

Linksys Wireless Router :: Ea4500 Dlna Server No Time Seeking?

Jul 9, 2012

dlna server of ea4500 does not supports time seeking? No rewind? I have tryed to plug usb-flash with video files for testing before buying an external HDD and... REALLY no time seeking?

View 3 Replies View Related

Linksys Wireless Router :: EA4500 - Media Server With USB Hard Drive

Jan 7, 2013

EA 4500 seems to work fine. Have a Seagate 3 TB HD connecfed to USB. Have LG Smart box connected to EA4500 by Cat5e cable. HD hard drive contents shows and accesses ok on PC via wireless. Smart box showed HD but only media files in "documents" directory, did not show "TV" & "Movies" directories.

Reset Router Media Server Access with "TV" & "Movies" directories - presto LG smarbow showed directories now and worked fine. This morning will no longer show "TV" & "Movies" directories on Smart box. Have tried deleting and resetting Router Media Server Access with "TV" & "Movies" directories several times, no luck.

View 1 Replies View Related

Linksys Wireless Router :: Ea4500 Media Server - Scan Does Not Work

May 28, 2012

I added some files to the hard drive which is connected to EA4500 by USB. I went to the Storage--Media Server Tab and clicked Scan All. I turned on the TV and pointed the DLNA Media Server at the hard drive.
 
The new files did not show up. They did show up a few hours later. Does the Scan button do anything?

View 3 Replies View Related

Linksys Wireless Router :: EA4500 FTP Server Remote Access Fails With Firewall

Sep 1, 2012

I tried to remotely access my disk connected to the USB port of the EA4500 and it failed until I disabled the IPv4/IPv6 SPI Firewall options. Surely, the firewall should not block the router's own FTP server!

View 8 Replies View Related

Linksys Wireless Router :: WRT320N - Setting Up Static LAN & Custom DHCP Pool

Dec 18, 2012

I'm following a tutorial that 'dumbs down' the modem and lets me use the router for everything.
 
It asks me to set up a static LAN IP (10.x.x.x range) and edit the DHCP pool of the router. When I'm logged in to the routers admin, it doesn't seem I'm able to do any of this.
 
Earlier in the tutorial it also asked me to set up a static IP for the router, which I did I suppose.
 
I've added a screenshot of the admin panel, in case that's relevant.

View 1 Replies View Related

SWR54BGA / Router Won't Register With The Pppoe Server

Dec 24, 2010

There is one router ( SWR54BGA ), wan interface functional ( connected as a dhcp client to the lan interface of another router , packets are forwarded). When i connect the wan interface to the isp line, and provide the pppoe login details ,it won't work. When i try to connect manually to the pppoe server from the wan configuration page, after about 30 sec i get the connection failed message.Is the firmware corrupt, should i go the ddwrt route?

View 2 Replies View Related

Poweredge T410 Server - Custom Dell Configurations

Jan 17, 2011

I'm a Dell Partner and I've been trying to figure out why I can't order a Poweredge T410 server with 8GB of RAM. The only options are 3GB, 4GB, 24GB, or 32GB. I ordered a T410 for another client at the middle of last year with 8GB of ram. Now they don't offer that. I realize I could buy RAM after the purchase, but I'd rather just buy the server configured the way I need it for the client and not have to worry about separate warranties on the aftermarket memory, etc.

Also, I want to do a custom RAID configuration, as suggested a few times on the forum. Two harddrives in a RAID-1 array for the OS, and four harddrives in RAID-10 (or RAID-5 with a hot spare) array for data.

I did an online chat with Dell and the rep said it was not possible, i.e. what you see in the online configurator is what you get. Do I need to call Dell to get a custom configuration?

View 4 Replies View Related

Linksys Wireless Router :: Add Pppoe Passthrough In E3000?

Sep 22, 2011

I have e3000 but in VPN Passthrough I don't have ( pppoe passthrough ). Just I have is ipsec + pptp + l2tp only. How could I add ppoe passthrough in my e3000.

View 2 Replies View Related

Linksys Wireless Router :: E3000 - Pppoe VPN Pass Through

Aug 20, 2011

I have e3000 but in VPN Pass through I don't have ( pppoe pass through )
 
Just I have is ipsec + pptp + l2tp only
 
How could i add ppoe pass through in my e3000

View 1 Replies View Related

Linksys Wireless Router :: When PPPoE Dual-Access Will Be Available For EA650

Dec 27, 2012

I extremely need PPPoE Dual-Access on my EA6500.I'v paid $225 and can't watch IPTV So, I'm somewhat disappointed with tis issue...

View 9 Replies View Related

Linksys Wireless Router :: Routing PPPoE Subnet Using EA3500

Oct 4, 2012

I was assigned a static block over PPPoE from the ISP.  I can connect to the internet using the gateway address but I need to route the other static IPs to my servers.  I might say that I accomplished it on a couple of older routers - E1200 & WRT120N, but I cannot get it to work on my new EA3500.  I have 5 usable IPs plus the gateway IP that is assigned with the PPPoE connection on the WAN port.

View 8 Replies View Related

Linksys Wireless Router :: WRT54GS - PPPoE Automatic Login?

Aug 2, 2011

I have a WRT54GS wireless router.  I can successfully set up the router with my DSL modem for PPPoE.  Here's my problem.  The router configuration requires you to put in the userID and password, then logs you in to your ISP automatically.  I DON'T want it to do that.  Is there any way to configure for PPPoE where ISP login is controlled manually; i.e., when the user tries to connect to a web page, a dialog pops up for entering the password?

View 1 Replies View Related

Linksys Wireless Router :: Brand New EA3500 Won't Connect To PPPOE

Oct 24, 2012

When the ethernet cable is plugged directly into my laptop i can input my user name and password and connect directly without a problem. But as soon as i plug the cable into the router, the activity lights turn off like its not plugged in on the other end...which it is. So when going through the setup process, both using the cd and inputting the information on the web based setup. It does nothing, the automatic setup says the cable isnt plugged in. When using the browser setup i can click connect as many times as i want and it does nothing but say disconnected.

View 9 Replies View Related

Linksys Wireless Router :: Wrt54gx4 Can't Connect To Internet By PPPoe

Feb 18, 2012

I am using wrt54gx4. I have a IP camera connected to it. I can view the live images on the intranet and internet. Not too long ago my DSL company upgraded my DSL modem to a newer model. Then I can not connect to the internet by PPPoe. DHCP is fine. So the only connection type works is DHCP. But now I can not view the live images on the internet. I can only view the live images on intranet( I mean if I open web browser and type url.. is the port, I can view the live image).

View 1 Replies View Related

Linksys Wireless Router :: Frequent PPPOE Disconnects On E2500?

Dec 13, 2012

I have a Cisco/Linksys E2500 router that I have had for over a year and it has worked without issues for over a year.  However my wireless ISP just switched my CPE from A Mikrotik wireless radio to a Ubiquiti wireless radio.  As soon as they did this my PPPOE sessions from the E2500 (acting as my PPPOE client) start disconnecting and reconnecting every few minutes causing major problems with my internet and voip connectivity when it looses connectivity every few minutes.
 
The strange things is if I connect my much older WRT54G router as a PPPOE client (with the same exact PPPOE configuration), it works just fine and I don't have any PPPOE disconnects. 
 
I upgraded to the latest firmware on my E2500 and nothing changed, it still disconnects my PPPOE sessions probably close to 50 or 100 times an hour. 
 
I'm thinking it's some sort of compatibility issue between the Ubiquiti Nanobridge Radio CPE and the E2500 router acting as my PPPOE client.  Also another thought was that perhaps my ethernet port wasn't negotiating speed/duplex correctly on the E2500. 
 
Is there any way to hard code the speed/duplex on an E2500?  I can't seem to find any spot with that setting.

View 8 Replies View Related

Linksys Wireless Router :: Configure Pppoe On WRT120N It Say It's Connected But Cannot Access Wan

Aug 11, 2010

I have configure pppoe on my WRT120N it say it's connected but cannot access wan side of the router.

View 5 Replies View Related

Linksys Wireless Router :: E1000 Suddenly Stopped Connecting PPPOE?

Jan 24, 2013

I have a Linksys E1000 router just upgrade to the latest 2.1.0.2 firmware...I have a PPPoE connection which used to run smoothly on the router..however off late...suddenly the router stopped connecting..it always shows "connecting" in the status tab of the router page...and eventually says failed to obtain IP address...however when I attach the cable directly into my PC it works just fine.I also had a word with my internet provider...he's kept the MAC open (or something like that)  so he said that isn't the issue and he keeps saying there must be some issue with the router. However, occasionally the router DOES connect for half hour or so and then just refuses to connect again !..

View 2 Replies View Related

Linksys Wireless Router :: E900 Randomly Dropping PPPoE Sessions

Jun 20, 2012

New E900 router drops PPPoE session and gets new IP address randomly every 1-20 hours. Tried different E900, does the same thing.  Disabled IPv6, no change.  Upgraded FW from 1.0.00 to 1.0.01, no change.  I have an SPA112 ATA behind the router and it has to re-register with the VoIP provider every time the IP address changes, so I'm afraid of my call getting dropped if this occurs while I'm on the phone.  Using an old WRT54G or a different brand of router it will keep the same PPPoE session for weeks, so it is not the ISP.

View 2 Replies View Related

Linksys Wireless Router :: EA6500 PPPoE Internet Connection Not Working?

Nov 29, 2012

I recently buyed a Linksys EA6500 wireless router. I accessed [URL] to access the settings interface of the router. Went to "Connectivity Internet Settings" and chose type of the internet connection as PPPoE. Entered the username and password, clicked ok.
 
No internet access.

View 9 Replies View Related

Linksys Wireless Router :: E3000 - PPPOE Connection Is Getting Frequently Disconnected

Mar 6, 2012

I want to share PC internet (PPPOE connection) on my linksys wireless router (E3000)Problem : When i directly connect internet wire in router, pppoe connection frequently gets disconnected. So what i wanted was to share my pc internet on router.I have two lan card on windows 7 installed PC, 1st lan card is connected to internet cable and i can access internet on pc, second lancard is connected to wireless router. So basically what i want is to share pc internet ( PPPOE ) on wireless router through DHCP connection type.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved