Linksys Wireless Router :: WRT54G2 Can't Get IP From PPPoE Server
Sep 19, 2010
I installed a Linksys WRT54G2 router earlier this year and set my Siemens modem from AT&T(Actually from SBC before the two merged) in bridge mode. I did this so I could change the NAT setting on our internet, which was interfering with my Xbox. It worked for about 4 or 5 months with little to no problems. Recently, however, the internet has been disconnecting and when I check the status page on the router it says it is disconnected. Sometimes clicking on the connect button will work, but usually it will say "Connecting" and keep refreshing the page for a little while without any change, then give me a message saying it couldn't get the IP from the PPPoe server. Turning it and the Siemens modem on and off and fiddling around seems to solve the problem, but only temporarily. Interestingly enough, I don't think it ever interferes with my Xbox. Until recently, the Xbox was set as the highest priority on the QoS page, but I changed the computer to the highest priority and it hasn't worked. In addition, the small, thin green light bar just below the Linksys logo on the top of the router has just recently started changing to orange occasionally
View 9 Replies
ADVERTISEMENT
Sep 20, 2012
I have been working on this for hours and getting frustrated! This router has been set up for over a year with no trouble, but recently had trouble connecting with my wireless devices and was kicking my wired (ethernet) laptop off when it is usually on all the time.
Now, my wired connection works through the router, the wireless devices all connect to the network but do not have access to theinternet. From the router's setup page, when I enter my PPPoE information and go to status and connect, it tries to connect a few times then gives me the error message 'cannot get IP address from PPPoE server"
I have tried updating firmware, resetting, restarting, recycling power, chat support with ISP and chat support with Linksys. Have verified my username and key and those are correct otherwise I'd have no internet access at all. I do have wired access but not wireless. The wired connection does go through the router.
Bridging - my modem is a bridging modem only, so it shouldn't be that.
View 4 Replies
View Related
Oct 13, 2011
I am using the WRT54G2 connected to a cable modem that requires a PPPoE login. I followed the Service Providers instructions and cloned the modems MAC address to the WRT54G and setup the PPPoE user id and password. I can then plug my PC into one of the Ethernet connections on the back of the WRT54G and everything works as expected. First I connect to the WRT54G2 and then I open a PPPoE connection in my network settings and it logs into the service provider and everything works as expected. But when I connect to the WRT5G2 wirelessly I connect to the AP fine. When I open the same PPPoE connection to the service provider it fails, the message says I have the wrong userid or password or that the protocol is not supported. Of course I know the userid and password is correct because it works when connected with Ethernet cable. I have tried disabling the security on the wireless network but that did not seem to work.The modem is a HomePNA HCNA Voice Endpoint.I am at the latest firmware 1.0.04.
View 7 Replies
View Related
Nov 17, 2012
I have a Linksys WRT310N V1.I am trying to connect this via PPPoE to another Thompson router/modem that has been succesfully switched into BRIDGE mode.The Linksys router is conneted via ethernet cable to an ehternet port on the Thompson router.The ADSL cable is pluggedinto the WAN port of the Thomson 'bridge'.There is no cable in the WAN port of the Linksys router.
The Linksys router is set up to connect over PPPoE using the username and password that was given to me by my ISPs tech support (checked and double checked).The DHCP server on the Bridged Thomson is set to ON. DNS is set to OFF.the DHCP server on the Linksys router is set to ON.
View 2 Replies
View Related
Jul 22, 2011
I recently bought an E3000. I am trying to setup a wireless home network.Google and tried a lotta things (power cycle the most no. of times ). Nothing worked.So I poked around. Looked up the IPConfig of my PC with wire connected directly(no router), was 192.168.0.xxx. So I hit 192.168.0.1 in my browser address bar, and it came up with the login page for a D-Link DIR600. A wireless router with wireless disabled. Apparently this is being used as a switch by my ISP. This I know cause I checked the active connections and DHCP reservations on the D link and it showed up about 100 different PC's (including MAC and IP addresses).
View 9 Replies
View Related
Dec 22, 2012
I look forward to the new firmware can improve this problem.
View 3 Replies
View Related
Oct 11, 2011
I have a problem with my router, WRT54G2. I was upgrading my firmware when my computer froze up, so I had to exit. Afterwards, I could not connect to the web based setup page anymore. I did a factory reset and installed it again with Network Magic and set up my wireless key. It is working now however, I cannot get into the web based setup page. Whenever i go to 192.168.1.1 and enter my info, it just says 500 Internal Server Error. I was always able to access this page, now I can't, so I assume it's not working because of the interrupted firmware update. I do alot of mac filtering and I limit the amount of IP addresses my router gives out so if anyone hacks my security key, they still won't be able to connect, so accessing my router setup page is important to me. I have reset (hold down reset button for 30 secs - 1 minute) the router many times and still nothing. I mean, the router still works. My brother and I can still connect with our laptops, I just can't get to the web based setup page.
View 7 Replies
View Related
Dec 24, 2010
There is one router ( SWR54BGA ), wan interface functional ( connected as a dhcp client to the lan interface of another router , packets are forwarded). When i connect the wan interface to the isp line, and provide the pppoe login details ,it won't work. When i try to connect manually to the pppoe server from the wan configuration page, after about 30 sec i get the connection failed message.Is the firmware corrupt, should i go the ddwrt route?
View 2 Replies
View Related
Oct 9, 2011
I have a Linksys WRT54G2 V1and I am trying to hook it up to my broadband modem after hooking up the connections it still does not recognize?
View 2 Replies
View Related
Mar 27, 2011
Yesterday my wireless internet suddenly stopped working. I plugged the ethernet cable directly from the modem to the computer and everything was fine, so I reset the router, reconnected it to the modem, and went to the setup page 192.168.1.1. I reconfigured the router on the setup page, leaving all previous settings the same (except I renamed the network from linksys to our own name and reconfirmed the WPA Personal password). My computer can connect to the wireless network but I can't go online.
View 9 Replies
View Related
Jan 18, 2013
Really not grab Router Gateway, even as did the 30-30-30 reset because I had all the lights on, and is still in trouble. I am currently connected via ethernet to the router only. And yet not grab us Links Home door. The lights now are Power, WIFI and Port 4.
View 2 Replies
View Related
Jul 4, 2011
I have this router back in my home office for my wife's Mac laptop. I recently purchased a new Sony TV with internet access capability and was hoping to gain access through my router, however during set-up attempt it will not connect. My wife is able to use her laptop in the same area as the TV.
View 3 Replies
View Related
Nov 28, 2011
I have a WRT54G2 v1 (no new firmware available) with a cable-modem connection (Motorola Surfboard), every thing works perfect but when my ISP goes down and then back up I cannot get the router work, LAN or Wifi connection. I have ping response to the router and I'm also able to get into the admin page. The only way to recover is restarting the router and sometimes releasing DHCP and then Renewing it, and the Wan connection actually gets the same IP it had before.
View 3 Replies
View Related
Nov 4, 2012
I'm not really computer savy and I have an old wireless G Broadband router model # WRT54G2 V1 .
View 1 Replies
View Related
Oct 5, 2011
Went away on vacation for a couple of weeks and when I got back my Linksys WRT54G2 has lost it's configuration. It's showing a WiFi signal, but is no longer password protected.
I've tried connecting with a desktop on the same network, to 192.168.1.11, but that address is not connecting. I tried to reach it with my iPad wirelessly, and it's giving me the login screen, but not allowing me to login. I tried to use the reset button on the back to reset it to the factory default, but then I should be able to login with no username and the password of "admin", correct? But that's not getting me in either.
I'd like to get this network password protected again and not offer a signal to all of my neighbors.
View 2 Replies
View Related
Oct 4, 2008
I've tried to connect my father's laptop and my father's girlfriend's daughter's PC to my Linksys Wireless Router, model #WRT54G2 V1. So far, I have steady and fast internet access on my PC which so far I've only gotten my father's laptop to connect through. However, I can't figure out how to get her PC to get internet access through my router. I'm mediocre at configuring computers, and I'm absolutely terrible at routers. :/ There was the possibility that her computer isn't new or advanced enough or whatever to be compatible with a wireless router, but at the same time she has a Wireless Network Setup Wizard app. in the control panel area, so wouldn't I be correct in assuming that if a computer has a wizard dedicated to it, it is compatible? I've run Wireless Network Setup Wizard as well as just plain Network Setup Wizard, and I've had them both read that it was successful connecting to my Router's network...but where do I go from there? I've never had to mess with a PC before so I'm not entirely sure. She has a modem, which can not be plugged into the phone jack at the same time as my modem otherwise we both do not have internet access, however if one of us plugs in that person is fine, so that's when I figured I'd try to get her PC into my network with my dad's laptop. Also, we have a Broadband connection setup through Verizon, if that matters at all. Does she need a modem to hook up to my network at all? If so, does that modem need to be plugged into the phone jack? If required I'll give her OS and PC specs and such, but from what I know just being on her computer she runs Windows XP as an OS and her computer is an "eMachine".
View 9 Replies
View Related
Aug 12, 2010
I have been having trouble with my wireless router for the past month and not sure what is up with it. I have recently moved and got it working for a day then the wireless did not work and i was not able to access the setup webpage either. What I ended up doing was upgrade the firmware to the newest one and it worked well for about 2 weeks but then started again and the only way it works is to reboot the router but then the next day it will not work.
View 3 Replies
View Related
Sep 22, 2011
I have e3000 but in VPN Passthrough I don't have ( pppoe passthrough ). Just I have is ipsec + pptp + l2tp only. How could I add ppoe passthrough in my e3000.
View 2 Replies
View Related
Nov 17, 2012
I've been using my EA4500 since it's original launch date as a PPPoE router through another router/modem which is the Netgear DG834G V4 set to Modem Only mode which was working fine for a long time!A month ago, a friend wanted to borrow the Netgear Router and after he gave it back I reset it like I always do and entered my settings in router mode(i.e. username and password) to check if I havewe working Internet connection and that the router is working properly and it was working properly like it was before I lent it. Now comes the problem, if I keep using the Netgear router as the PPPoE handler and make the EA4500 work as "Automatic Configuration DHCP" it works flawlessly but if I set the Netgear router to modem mode and make the EA4500 handle the PPPoE connection, the report in the troubleshooting tab keeps on saying "Connecting" endlessly!
Note: I've replicatedthe settings that I used on both router before and after lending it to my friend so there's no difference in settings!
View 6 Replies
View Related
Aug 20, 2011
I have e3000 but in VPN Pass through I don't have ( pppoe pass through )
Just I have is ipsec + pptp + l2tp only
How could i add ppoe pass through in my e3000
View 1 Replies
View Related
Sep 23, 2011
I am trying to password protect my router but when I go into wireless> security mode and click on WPA or any of the other choices it goes back to disabled.
View 3 Replies
View Related
Jan 4, 2012
A couple of days ago I noticed my download speed (from my own webserver) has slowed down. I checked my wireless connection and saw that the radiotype was now 802.11g instead of 802.11n, what is always has been. I looked at the Wireless configuration in the router's webbased config panel, but the only things listed there are "Disabled", "Mixed", "Wireless-G Only" and "Wireless-B Only". A scratched my head a bit, wondering wether or not I really bought an N router or just a G router. But IIRC I really bought an N router. It said so on the bill. Also, when I check the user manual, page 14 says I should be able to select "Wireless-N Only".
View 5 Replies
View Related
Sep 16, 2008
I just bought this router yesterday. Can someone link me the most up to date firmware, and explain how to install it?
View 9 Replies
View Related
Mar 25, 2009
I Installed the DD-WRT firmware on my linksys WRT54G2 v1 router....ibut now the connection keeps on dropping...not stable, how do I roll back to the original linksys firmware?
View 9 Replies
View Related
Sep 13, 2011
I've needed to power-cycle my router every 2 hours. Usually it can last 2 weeks before needing to power-cycle (a process I've done for the past 2 or 3 years). This actually happened before for me a couple of months ago, but I did a firmware update along with a reset, and it looked like everything went back to normal.
But last Saturday I had to power-cycle it twice, then it didn't have any problems all day Sunday. But yesterday it went back to needing to be power-cycle it every 2 hours. My computer is physically connected to the router and is working perfectly no problems at all. But my parents use the wireless for their PC and laptop, and I use it for my 360, PS3, and Wii, so having to power-cycle it every 2 hours would be a pain.
I was wondering if this is a sign of the wireless in my router dying and in need of a new one, or is there some possible fixes I can do in order to repair it.
Mixed Mode
Wireless Channel 1
No WPA (Something I'm planning on fixing)
View 3 Replies
View Related
Dec 29, 2011
I recently found that whilst using my WIRED connections, web pages have been opening slower at times. My ping times to google.com usually is around 72-84 ms which I continue to get if I hook up the cable modem directly to the PC. As soon as I utilize the Linksys router, I start getting higher ping times anywhere from 72-300 ms. Firmware version is 1.5.01 which I recently upgraded to. I tried resetting and so on. Is there an older firmware version that works better? I'm currently running Windows 7 Ultimate 64-bit.
View 1 Replies
View Related
Jul 8, 2011
When I connect the ethernet directly to my mac the internet works fine, but when I try to connect through my Linksys WRT54G2 V1 Wireless-G Broadband Router I can't connect to the internet. Omitting a few minor problems, my router has been working fine for the past year and a half. Recently it started giving me trouble so i have started trying a number of things to fix it, but I'm no expert in this category. The other day i tried updating the firmware which actually worked for a couple of hours, but then stopped working again.
View 3 Replies
View Related
Jan 13, 2012
I will be setting up a new computer this weekend. I presently have a WRT54G2 wireless-G router and have configured it to an IP address that works with my AT&T(Bellsouth) broadband modem (Westell). When I reconnect it to my new computer, should I first just connect the ethernet cable to the modem as if I don't have a router (like I did for years) and then go into the instructions for setting up the router via the DVD but enter the IP address as I have it working now?
View 3 Replies
View Related
Mar 11, 2012
I have a Linksys WRT54G2 V1 and since I bought my new notebook with Windows 7 I can not access the wifi. I have another notebooks with Windows Vista and a PC with Windows XP that connect perfectly, but with Windows 7 gives me error when loading the password.I Update the firmware to version 1.0.04 (this the latest version I found on the cisco site), but still don't work.I Try chatting with Cisco support and was told he was no longer under warranty.
View 6 Replies
View Related
Dec 7, 2012
I have Linksys WRT54G2 V1 it suddenly died yesterday. I does not broadcast any wifi, I tried connecting via cable but there is no LAN, "Network Cable Unplugged". I also tried to do 30 sec reset even the 30/30/30 reset but no success. The front lights and power supply are blinking exept the Wifi and Power indicators.
View 1 Replies
View Related
Jul 24, 2008
How can I use the dhcp reservation with this router? I've network printer and i can't use it.
View 6 Replies
View Related
Jan 30, 2011
I can't seem to login to my admin. the IP for me is 192.168.0.1 and I can't login. I tried resetting the router a few times and no luck.Is there ANY other way to reset the username and password?
View 6 Replies
View Related
Jul 7, 2011
I recently upgraded the OS on my laptop to Windows 7, which wiped out most of my older Vista settings. When I try to connect to my home network, I am prompted for a security key (network key?). How do I find the security key? I can't find any of the paperwork that came with my router.
By the way, I am currently using my desktop, running under Windows XP.
View 2 Replies
View Related
