I have Linksys WRT54G2 V1 it suddenly died yesterday. I does not broadcast any wifi, I tried connecting via cable but there is no LAN, "Network Cable Unplugged". I also tried to do 30 sec reset even the 30/30/30 reset but no success. The front lights and power supply are blinking exept the Wifi and Power indicators.
View 1 Repliesthis issue with my WRT54G2:
- when i open more than 2 or 3 browser windows or anything that access internet, it stop routing
- shutdown and power up make it work again (then stops again after some simultaneous tcp connections)
- hard reset dont work
- WRT54G2 V1 Firmware Version: 1.0.04
I have a Linksys WRT54G2 V1 router that doesn't work. The lights all blink properly, but the internet connection part doesn't seem to be working. When connecting internet line directly to the computer, my internet works, but when connecting it to the router to the computer, it doesn't. I've tried resetting, unplugging for 30 minutes, etc. Putting in 192.168.1.1 brings up nothing on my web browser. Pinging it says connection timed out. My ipad is able to pick up the router signal as it shows the wifi bars on top, but when trying to use the internet, it says that it's not connected to the web.
View 2 Replies View RelatedI'm using an E2500 and the Power LED started blinking this week.From the manual, this means “Flashes slowly during bootup, during firmware upgrades, and druing a Wi-Fi-Protected Setup Connection.” We have a wireless printer (wireless disabled), and a Kindle that does use wireless. All other computers are hard wired. I have not started a Wi-Fi protected setup. The router has been in use since the third week in October, and is more or less OK even though the Power LED is flashing. How do I get the Power LED to stop flashing?
View 3 Replies View RelatedAre the lights supposed to always blink in random order..the power light is solid but other 2 beside it and the 1 where the desktop is plugged in are blinking like crazy.
View 5 Replies View RelatedI just bought an EA4500 and I set it up and about every 5 minutes it starts blinking slowly and dropping connection.
View 4 Replies View RelatedI'm having a problem with my WRT54G wireless broadband router. The power light is blinking and I can no longer access the internet. What should I do. I can't seem to understand the self-help on your site.
View 2 Replies View RelatedI got this replacement router and it is not even a week old and it is doing same thing the previous one was.
View 1 Replies View RelatedI have a problem with a LinkSys WRT610N router (v1).
I have just bought it used. The problems: I see the power led blinking all the time. I can't connect to 192.168.1.1. I do not notice any effect on the leds when pressing the reset button (I feel a soft click when I do that, but none of the leds seem to realize). The manual states that the led should stop blinking after the "self-diagnostics" ends.
My configuration is DSL connection (by AT&T, phone cable), a Siemens 4100 modem, an ethernet cable into the LinkSys router, then an ethernet cable into a Linux PC. Everything is wired. I see the green light of the LAN connection to my PC, the world blue icon and the USB icon stable on, a shy orange led on in the middle (wireless?) and the power blue led blinking. The PC is configured with DHCP, and I can access both the modem (192.168.0.1) and the internet. The gateway address is the one of the modem (again 192.168.0.1). In summary, the ethernet of the router seems to work, but the router is completely transparent, inaccessible, unconfigurable, apparently unresponsive. Trying to connect to 192.168.1.1 (the supposed default address of the web interface of the router, which is different from the 192.168.0.1 of the modem) I get a timeout error, and I can't ping that address. The modem is configured to handle the PPPoE connection, which I am not sure what it means but the text description suggests in this mode I should be able to access the router, provided that its address is not conflicting with the modem's. If I disconnect the modem from the router, DHCP does not get any address. If I force one, 192.168.1.1 still does not respond to pings.
So Is it normal not to notice any reaction when hitting the reset button? is the object just broken, except that the ethernet subsystem still works?
the power light on my wrt54g v2.2 router keeps blinking and it wont connect to the internet when connected
View 3 Replies View RelatedMy Wireless-G WRT54G router has a blinking power light and the startup software says "Unable to connect to the Router! Check that the Router has been connected to the computer, and that your Ethernet adapter is working." I tried uploading the firmware but I can't get to the router page to update. Is there a known problem or solution here or am I just going to have to find the router page?
View 9 Replies View RelatedI have an E1000 wireless router and after rebooting it from the web admin page it won't stop blinking. I tried following the reset instructions on this page but it is still blinking.
[URL]
I can't access 192.168.1.1 via my browser either. Is there anything else that I can try before considering it defective?
I went online with a tech real quick before I found I beyond complimentary tech support. They say my router is working like a switch. I cannot get any wireless access and to the three direct connections to the router only one is working. The lights are constantly blinking, with the power light blinking every so often
View 1 Replies View RelatedSo I recently upgraded from a WRT54GS to a WRT160N v2, all was well and good for about 3 days. Then I would lose my internet connection every 5 minutes or so, it would fix itself by the time I could open up command prompt and start pinging to pin point the problem. I decided I would update the firmware to see if that would fix the issue. Since doing that the power light has been blinking non stop. I've tried restoring it to factory defaults by holding the reset button for 30seconds, turning it off for 2 minutes and back on. That little blue light just keeps flashing. I can't even access the router setting page using 192.168.1.1. My OS is Windows xp x64 sp2, and I have DSL.
View 9 Replies View RelatedSomehow in the process of researcing how to add my new laptop to the router, the router quit working and is now just blinking the blue panel lights.I was attempting to download Cisco Connect to my flash drive and instead it began to execute and I aborted that in about 10 seconds.
View 1 Replies View RelatedI had successfully set up my new WRT150N router and it was working. But then it just stopped after about 12 hours. All the lights on the front of the router are blinking. When I directly connect to the router, my computer can't detect it. I've browsed through these forums a bit and tried a few things - the reset button (60 seconds), unplugging the router, downloading the EasyLink Connect tool, but I'm still stuck.
View 5 Replies View RelatedWhen I came home tonight, the lights on my E1000 hardware version 1 (that I have had for only 9 months) were, as best as I can describe, blinking like a digital clock blinks 12:00 over and over. All of the blue LEDs would light up at once, and go off, repeatedly and rapidly. This is the second time this has happened - the first time (about two weeks ago) I called a techie friend and he had me hard reset the router (30 on 30 off 30 on) and it worked, I just had to set up my wireless network again. This time, I just unplugged the cable from the back of the router, waited about 15 seconds and plugged it back in, and it went back to normal.
In case someone may be wondering, unplugging the from the surge protector did NOT work; when I first noticed the lights blinking, I unplugged it from the surge protector, waited about 10 seconds, and plugged it back in; the lights continued their rapid erratic blinking. I then did what I described above - I plugged it back into the surge protector, and then unplugged it from the back of the router, waited, and plugged it back in and it was back to normal.
I thought perhaps it needed a firmware upgrade, but checking the website, while I was able to locate the site to upgrade the firmware for E1000, I could only see an upgrade for hardware Version 2, and my router is Version 1 - which, from what I understand, is NOT what I want, as that firmware is for a different hardware version and may cause problems on my Version 1 router.
While my router seems to be fine now. Is my router starting to kick the bucket already? I haven't had it that long - bought it last September. Do I need to upgrade any software or firmware for it? If so, where do I get the correct upgrade for my hardware version?
I need fixing my router. I updated the firmware and it said the upload has failed ever since then:
-the router doesn't work
-blinking power light
-DMZ light doesn't turn on
-can't access 192.168.1.1
My router is a WRT54G v5
the power light on my wrt54g v2.2 router keeps blinking and it wont connect to the internet when connected, what should i do?
View 1 Replies View RelatedI am on a surge protector and we lost power last night. This morning we were stilling experiencing a brown out but now the power is back 100%. I've walked through the E1000 router reset and not matter what I do, all the lights except the power light blink rapidly and dimly. Could the router be fried even though it's on a surge protector???? It's less than 6 months old so hopefully still covered by warranty.
View 9 Replies View RelatedI cannot get access into my router because it doesn't seem to have a gateway IP address, although it is assigning my computer an IP address.
View 1 Replies View RelatedNo download available and none available via Linksys Live Chat or FTP and having spent the best part of the week trying to find relevant firmware on other forums I decided to come here to get answers to the following questions, hopefully from version 1.0 experienced owners or not.
#1. Can the firmware of version 2.0 and 3.0 be reduced to flash version 1.0?
#2. When diagnosing the blinking power light issue by connecting directly to the router and the network card using "ping -t 192.168.1.xxx" which network address do I use, 192.168.1.1 or 192.168.1.2 to 2xx?
I get a reply using 192.168.1.1 but I'm not sure that works when using the TFTP Utility if it's the wrong address on my Laptop to ping?
I have a Linksys WRT54GS vers 7.2 Router on an iMac OS X Leopard. The other day I was in the middle of downloading an upgrade for the router when Firefox gave me this message: "Firefox can't find the server". I was no longer able to access the internet, and the router's green power light was left flashing. It flashed for over 24 hours. I tried unplugging the router and shutting down the computer, then plugging in the router and turning on the computer. (I don't have a modem.) The light was still flashing. I tried pressing the logo button for 5 seconds. Still flashing. Tried pressing the reset button in the back. Still flashing. 'I can't get on the internet or into the router. Linksys live chat gave me a link to "Upgrading the router’s firmware using the TFTP utility", which involves a download, but I can't download anything because I can't access the internet.
View 8 Replies View RelatedI've seen related to flashing power lights on the router involve fixes via firmware upgrades off a PC.I'm on an iMac os 10.6.7. The WRT54 used to work as a wireless modem a couple of years ago. Tonight, it doesn't. power light blinks. Can't access any webpage interface for the thing. Reset, power down, computer restart, cable modem turn off don't change anything. Is there anything that can be done other than tossing the linksys? If that is the only option, are there wireless routers more suitable for a Mac?
View 4 Replies View RelatedGot the EA2700 router and got the blinking defective firmware light right out of the box
View 3 Replies View RelatedIf I conact from the modem to the pc I have internet so it must be the router. The power light is blinking along with all the port lights. Power light is blinking one time slow 2 fast. Have tried holding the reset button for 30 seconds and unpluging for 30 seconds. Can not go to the ip address it times out. New firmware is not avalible.
View 9 Replies View RelatedMy router EA4500's Cisco Logo is Blinking and not connect with any device
View 5 Replies View RelatedSo I just noticed on my Cable modem the link light is blinking orange, per Motorola if its blinking orange - Computer is connected via a 10 mbps or 100 mbps Ethernet port.
On the Linksys E4200 status page it says
Internet Port Speed:
Internet 10/100 mbps
Local Port Speed Port 1 - 1Gbps
Maybe I just noticed this with this router, but I'm pretty sure this didn't start happening until I updated to 1.0.03.
Previously the link light was blue indicating a 1Gbps connection.
My wireless router is WRT54GC ver2.0. When I plug the power cable, all the LED light blinking including the power LED light. I try to find the firmware in the website, but here only have the version 1.0.
View 9 Replies View RelatedI have a Linksys E2500 and recently the power led light on the back of the router started blinking. The router itself seems to be working fine. I can access the router and the router seems to be assigning the IP addresses fine. I did look up the issue on the knowledge base and tried all the solutions but the light is still blinking. Not sure what to do anymore.
View 5 Replies View RelatedI have a Linksys WRT54G2 V1and I am trying to hook it up to my broadband modem after hooking up the connections it still does not recognize?
View 2 Replies View RelatedYesterday my wireless internet suddenly stopped working. I plugged the ethernet cable directly from the modem to the computer and everything was fine, so I reset the router, reconnected it to the modem, and went to the setup page 192.168.1.1. I reconfigured the router on the setup page, leaving all previous settings the same (except I renamed the network from linksys to our own name and reconfirmed the WPA Personal password). My computer can connect to the wireless network but I can't go online.
View 9 Replies View RelatedReally not grab Router Gateway, even as did the 30-30-30 reset because I had all the lights on, and is still in trouble. I am currently connected via ethernet to the router only. And yet not grab us Links Home door. The lights now are Power, WIFI and Port 4.
View 2 Replies View Related