this issue with my WRT54G2:
- when i open more than 2 or 3 browser windows or anything that access internet, it stop routing
- shutdown and power up make it work again (then stops again after some simultaneous tcp connections)
- hard reset dont work
- WRT54G2 V1 Firmware Version: 1.0.04
I have Linksys WRT54G2 V1 it suddenly died yesterday. I does not broadcast any wifi, I tried connecting via cable but there is no LAN, "Network Cable Unplugged". I also tried to do 30 sec reset even the 30/30/30 reset but no success. The front lights and power supply are blinking exept the Wifi and Power indicators.
View 1 Replies View RelatedI'm out in the middle of nowhere and just set up a few days ago a WRT54G2 V1 wireless 4-port router a family member had laying around. I had no problem getting it working and running. About an hour ago I noticed I wasn't picking up the wireless with my cell phone and went to check it on my laptop, I had no wireless connections available. It wasn't my adapter or anything since I know there are no other connections out where I am. I went to reset the router and found it had taken issue with that. Once I powered everything back on the router stopped responding and became "stuck" in an annoying state. It doesn't respond to the reset button, unplugging and replugging, nothing. Whether the internet was plugged in or not it will not move past what it's doing now.
View 5 Replies View RelatedIn my main office, I have a cable modem which is connected to my main E4200 router. All of my equipment (except my Ooma) is served by the E4200. The E4200 broadcasts a wireless network.In my basement, I have a Wii / entertainment center. The E4200 signal from upstairs isn't strong enough to stream video.
I bought the WET610N and have successfully set it up to interact with the E4200 wirelss network. I can hardwire my laptop to the WET610N and verify the internet works greatHowever, the Wii must connect over wireless. I have other equipment in the basement which would benefit from an internet connection. So, I want to A) connect the ESXS88W 10/100 8-port workgroup switch I have to the WET610N *AND* also broadcast a wireless signal in my basement (assuming the wireless network I see in the basement is the same "old" one from upstairs which has not benefited from the WET610N).
How can I set up my WRT54G2 to broadcast a wireless signal in the basement so that it leverages the E4200 signal served by the WET610N, while also having the workgroup switch offer hardwired connections to my other equipment (like Dish Network receiver)? It doesn't seem to work by just plugging the WRT54G2 into the workgroup switch.
I have WRT54G2 router. All settings are more-less default and the behavior is following.You start up the router. If you do not connect wireless device within 10 minutes, then you have to restart the router.You have assigned IP via wifi, and when you connect cable device to the router, the wifi PCs are disconnected.
View 3 Replies View RelatedDoes any body know what is the maximum of simultaneous connections that the AIR-LAP1131AG-E-K9 access point supports?
View 2 Replies View RelatedToday I read a comment on a review of DIR-615 [URL], saying it supports only 32 concurrent connections where as other routers support more than 200
View 6 Replies View RelatedI bought this router to temporarily replace my firewall while I wait for it to be replaced. We have a training center that when running full tilt, we probably have 50 devices trying to get on the internet.
View 1 Replies View RelatedI've setup access via our ASA5510 portal which is working fine but I can't seem to connectto the ASA when there are two active connections. If there is only one, it's fine.
Problem - Unable to Connect More Than Three WEB VPN Users to PIX/ASAProblem :Only three WEB VPN clients can connect to ASA/PIX; the connection for the fourth client fails.
Solution :In most cases, this issue is related to a simultaneous login setting within the group policy.Use this illustration to configure the desired number of simultaneous logins. In this example, the desired value was 20.
ciscoasa(config)# group-policy Bryan attributes
ciscoasa(config-group-policy)# vpn-simultaneous-logins 20Would this be the same thing?
If so how whould I check the existing setting in the GUI?
We are planning to use an ASA 5540 to terminate about 3000 IPSec connections. The maximum supported IPsec VPN Peers for this platform ist 5000, so this should be ok in theory.
What is a bit unclear to me is what exactly happens when (for whatever reason) all 3000 clients try to connect at once ? Perhaps it's not at once but depending on timers this could mean 3000 incoming IPsec connection within 10-20 seconds.
Will the the ASA cope with it ? I can't find any info regarding this on CCO. It's also not that easy to test/simulate.
This happens intermittantly. This results in most connections (but not all) being dropped. I will be unable to connect to web servers. My connection to videogame servers will drop. However, AIM will stay connected. These were done simultaneously. The same thing happens with my Cisco AE1200 and a D-Link 802.11g adapter I have. Disconnecting my adapter and reconnecting it solves the problem. I have tried doing a factory reset on the router and installing the latest firmware. It seems to happen more frequently when I am doing a lot of throughput (downloading a game on Steam, for instance) but other times it will happen when all I am doing is playing a game (like Tribes Ascend) which uses very little data. This is extremely frustrating. When I pay more than $150 for a piece of networking equipment, I expect it to last more than 3 years.
View 4 Replies View RelatedE3200 works great until I enable QoS. The device uses QoS and works find until reboot. If QoS is enabled and the device is rebooted, its stops routing from LAN side to Internet side. Administration-->Diagnostics allow me to ping/trace route to Internet sites and local LAN clients but cannot reach Internet from local LAN.
Windows networking icon indicates "No Internet access". I can ping other devices on local LAN.
Disabling QoS restores routing and you can re-enable QoS after that and all is well. Unfortunately, if there is a power failure when I', not there to disable/re-enable QoS afterward, other household members can't use the Internet till I get home.
Wondering if any other QoS users have observed the same problem.
I have been using a TP-Link WR1043-ND for a while now. It is configured as a dumb switch with DHCP disabled. Every other day or so, the device stops taking connections and I cannot access via the IP address. A simple power toggle resets everything immediately. Through this, the LAN connected devices never lose connectivity, I simply am not able to connect wirelessly or access the router via web browser.The only device I connect to the wifi is my phone, so it may actually be more frequently and I do not notice due to my low utilization (and I have 3G so I don't always notice right away if I'm connected). I have a WDTV Live SMP connected to one of the LAN ports and that functions non-stop regardless of the wifi. When the wifi is "down", my phone can see the network and attempts to connect. Sometimes it times out, other times I am repeatedly prompted that the password is incorrect, even though I am POSITIVE that I am entering it correctly. Once I toggle power on the router, the phone connects fine with the stored password.
I have updated to the latest firmware (about a month or so ago): Version: 3.13.12 Build 120405 Rel.33996n My hardware version is: WR1043ND v1 00000000 The router is connected (via LAN port 1) to a wall drop. My upstairs roomate maintains the gig switch and modem, as well as handling the network admin. I simply am using the router as a switch to provide extra ports and broadcast the network over wifi in my apartment.All that said: I need troubleshooting this router and it's configuration before I consider buying a more expensive replacement (and if I go this route, I might add a small switch as well to give me more than 4 LAN ports to work with). I am also considering flashing to DD-WRT before replacing as well to see if that makes a difference in reliability and uptime.
- How can I connect an old 2600 router to a linksys WRT54G2. to access the internet. I think it is not possible
- What device do i need to be able to do it
We have an AP541N that has been deployed to replace a Cisco 1200 AP (B/G radio). The 1200 functioned perfectly in our environment. The new AP541N on the other hand seems to work fine right after a reboot but immediately starts to degrade service. Over a short period of time, the devices bandwidth degrades to the point were the wireless network is not usable. This happens with just one device connected. Eventually, the device stops accepting client connections. We are unable to get any relevant logging out of the device to diagnose the problem.
View 84 Replies View RelatedI have a Linksys WRT54G2 V1and I am trying to hook it up to my broadband modem after hooking up the connections it still does not recognize?
View 2 Replies View RelatedYesterday my wireless internet suddenly stopped working. I plugged the ethernet cable directly from the modem to the computer and everything was fine, so I reset the router, reconnected it to the modem, and went to the setup page 192.168.1.1. I reconfigured the router on the setup page, leaving all previous settings the same (except I renamed the network from linksys to our own name and reconfirmed the WPA Personal password). My computer can connect to the wireless network but I can't go online.
View 9 Replies View RelatedReally not grab Router Gateway, even as did the 30-30-30 reset because I had all the lights on, and is still in trouble. I am currently connected via ethernet to the router only. And yet not grab us Links Home door. The lights now are Power, WIFI and Port 4.
View 2 Replies View RelatedI have this router back in my home office for my wife's Mac laptop. I recently purchased a new Sony TV with internet access capability and was hoping to gain access through my router, however during set-up attempt it will not connect. My wife is able to use her laptop in the same area as the TV.
View 3 Replies View RelatedI have a WRT54G2 v1 (no new firmware available) with a cable-modem connection (Motorola Surfboard), every thing works perfect but when my ISP goes down and then back up I cannot get the router work, LAN or Wifi connection. I have ping response to the router and I'm also able to get into the admin page. The only way to recover is restarting the router and sometimes releasing DHCP and then Renewing it, and the Wan connection actually gets the same IP it had before.
View 3 Replies View RelatedI'm not really computer savy and I have an old wireless G Broadband router model # WRT54G2 V1 .
View 1 Replies View RelatedWent away on vacation for a couple of weeks and when I got back my Linksys WRT54G2 has lost it's configuration. It's showing a WiFi signal, but is no longer password protected.
I've tried connecting with a desktop on the same network, to 192.168.1.11, but that address is not connecting. I tried to reach it with my iPad wirelessly, and it's giving me the login screen, but not allowing me to login. I tried to use the reset button on the back to reset it to the factory default, but then I should be able to login with no username and the password of "admin", correct? But that's not getting me in either.
I'd like to get this network password protected again and not offer a signal to all of my neighbors.
I've tried to connect my father's laptop and my father's girlfriend's daughter's PC to my Linksys Wireless Router, model #WRT54G2 V1. So far, I have steady and fast internet access on my PC which so far I've only gotten my father's laptop to connect through. However, I can't figure out how to get her PC to get internet access through my router. I'm mediocre at configuring computers, and I'm absolutely terrible at routers. :/ There was the possibility that her computer isn't new or advanced enough or whatever to be compatible with a wireless router, but at the same time she has a Wireless Network Setup Wizard app. in the control panel area, so wouldn't I be correct in assuming that if a computer has a wizard dedicated to it, it is compatible? I've run Wireless Network Setup Wizard as well as just plain Network Setup Wizard, and I've had them both read that it was successful connecting to my Router's network...but where do I go from there? I've never had to mess with a PC before so I'm not entirely sure. She has a modem, which can not be plugged into the phone jack at the same time as my modem otherwise we both do not have internet access, however if one of us plugs in that person is fine, so that's when I figured I'd try to get her PC into my network with my dad's laptop. Also, we have a Broadband connection setup through Verizon, if that matters at all. Does she need a modem to hook up to my network at all? If so, does that modem need to be plugged into the phone jack? If required I'll give her OS and PC specs and such, but from what I know just being on her computer she runs Windows XP as an OS and her computer is an "eMachine".
View 9 Replies View RelatedI have been having trouble with my wireless router for the past month and not sure what is up with it. I have recently moved and got it working for a day then the wireless did not work and i was not able to access the setup webpage either. What I ended up doing was upgrade the firmware to the newest one and it worked well for about 2 weeks but then started again and the only way it works is to reboot the router but then the next day it will not work.
View 3 Replies View RelatedI installed a Linksys WRT54G2 router earlier this year and set my Siemens modem from AT&T(Actually from SBC before the two merged) in bridge mode. I did this so I could change the NAT setting on our internet, which was interfering with my Xbox. It worked for about 4 or 5 months with little to no problems. Recently, however, the internet has been disconnecting and when I check the status page on the router it says it is disconnected. Sometimes clicking on the connect button will work, but usually it will say "Connecting" and keep refreshing the page for a little while without any change, then give me a message saying it couldn't get the IP from the PPPoe server. Turning it and the Siemens modem on and off and fiddling around seems to solve the problem, but only temporarily. Interestingly enough, I don't think it ever interferes with my Xbox. Until recently, the Xbox was set as the highest priority on the QoS page, but I changed the computer to the highest priority and it hasn't worked. In addition, the small, thin green light bar just below the Linksys logo on the top of the router has just recently started changing to orange occasionally
View 9 Replies View RelatedI am trying to password protect my router but when I go into wireless> security mode and click on WPA or any of the other choices it goes back to disabled.
View 3 Replies View RelatedA couple of days ago I noticed my download speed (from my own webserver) has slowed down. I checked my wireless connection and saw that the radiotype was now 802.11g instead of 802.11n, what is always has been. I looked at the Wireless configuration in the router's webbased config panel, but the only things listed there are "Disabled", "Mixed", "Wireless-G Only" and "Wireless-B Only". A scratched my head a bit, wondering wether or not I really bought an N router or just a G router. But IIRC I really bought an N router. It said so on the bill. Also, when I check the user manual, page 14 says I should be able to select "Wireless-N Only".
View 5 Replies View RelatedI just bought this router yesterday. Can someone link me the most up to date firmware, and explain how to install it?
View 9 Replies View RelatedI Installed the DD-WRT firmware on my linksys WRT54G2 v1 router....ibut now the connection keeps on dropping...not stable, how do I roll back to the original linksys firmware?
View 9 Replies View RelatedI've needed to power-cycle my router every 2 hours. Usually it can last 2 weeks before needing to power-cycle (a process I've done for the past 2 or 3 years). This actually happened before for me a couple of months ago, but I did a firmware update along with a reset, and it looked like everything went back to normal.
But last Saturday I had to power-cycle it twice, then it didn't have any problems all day Sunday. But yesterday it went back to needing to be power-cycle it every 2 hours. My computer is physically connected to the router and is working perfectly no problems at all. But my parents use the wireless for their PC and laptop, and I use it for my 360, PS3, and Wii, so having to power-cycle it every 2 hours would be a pain.
I was wondering if this is a sign of the wireless in my router dying and in need of a new one, or is there some possible fixes I can do in order to repair it.
Mixed Mode
Wireless Channel 1
No WPA (Something I'm planning on fixing)
I recently found that whilst using my WIRED connections, web pages have been opening slower at times. My ping times to google.com usually is around 72-84 ms which I continue to get if I hook up the cable modem directly to the PC. As soon as I utilize the Linksys router, I start getting higher ping times anywhere from 72-300 ms. Firmware version is 1.5.01 which I recently upgraded to. I tried resetting and so on. Is there an older firmware version that works better? I'm currently running Windows 7 Ultimate 64-bit.
View 1 Replies View RelatedWhen I connect the ethernet directly to my mac the internet works fine, but when I try to connect through my Linksys WRT54G2 V1 Wireless-G Broadband Router I can't connect to the internet. Omitting a few minor problems, my router has been working fine for the past year and a half. Recently it started giving me trouble so i have started trying a number of things to fix it, but I'm no expert in this category. The other day i tried updating the firmware which actually worked for a couple of hours, but then stopped working again.
View 3 Replies View RelatedI will be setting up a new computer this weekend. I presently have a WRT54G2 wireless-G router and have configured it to an IP address that works with my AT&T(Bellsouth) broadband modem (Westell). When I reconnect it to my new computer, should I first just connect the ethernet cable to the modem as if I don't have a router (like I did for years) and then go into the instructions for setting up the router via the DVD but enter the IP address as I have it working now?
View 3 Replies View Related