Linksys Wireless Router :: E3000 - Way Of Getting IP From Pppoe Server?
Jul 22, 2011
I recently bought an E3000. I am trying to setup a wireless home network.Google and tried a lotta things (power cycle the most no. of times ). Nothing worked.So I poked around. Looked up the IPConfig of my PC with wire connected directly(no router), was 192.168.0.xxx. So I hit 192.168.0.1 in my browser address bar, and it came up with the login page for a D-Link DIR600. A wireless router with wireless disabled. Apparently this is being used as a switch by my ISP. This I know cause I checked the active connections and DHCP reservations on the D link and it showed up about 100 different PC's (including MAC and IP addresses).
View 9 Replies
ADVERTISEMENT
Sep 22, 2011
I have e3000 but in VPN Passthrough I don't have ( pppoe passthrough ). Just I have is ipsec + pptp + l2tp only. How could I add ppoe passthrough in my e3000.
View 2 Replies
View Related
Aug 20, 2011
I have e3000 but in VPN Pass through I don't have ( pppoe pass through )
Just I have is ipsec + pptp + l2tp only
How could i add ppoe pass through in my e3000
View 1 Replies
View Related
Mar 6, 2012
I want to share PC internet (PPPOE connection) on my linksys wireless router (E3000)Problem : When i directly connect internet wire in router, pppoe connection frequently gets disconnected. So what i wanted was to share my pc internet on router.I have two lan card on windows 7 installed PC, 1st lan card is connected to internet cable and i can access internet on pc, second lancard is connected to wireless router. So basically what i want is to share pc internet ( PPPOE ) on wireless router through DHCP connection type.
View 1 Replies
View Related
Sep 19, 2010
I installed a Linksys WRT54G2 router earlier this year and set my Siemens modem from AT&T(Actually from SBC before the two merged) in bridge mode. I did this so I could change the NAT setting on our internet, which was interfering with my Xbox. It worked for about 4 or 5 months with little to no problems. Recently, however, the internet has been disconnecting and when I check the status page on the router it says it is disconnected. Sometimes clicking on the connect button will work, but usually it will say "Connecting" and keep refreshing the page for a little while without any change, then give me a message saying it couldn't get the IP from the PPPoe server. Turning it and the Siemens modem on and off and fiddling around seems to solve the problem, but only temporarily. Interestingly enough, I don't think it ever interferes with my Xbox. Until recently, the Xbox was set as the highest priority on the QoS page, but I changed the computer to the highest priority and it hasn't worked. In addition, the small, thin green light bar just below the Linksys logo on the top of the router has just recently started changing to orange occasionally
View 9 Replies
View Related
Nov 17, 2012
I have a Linksys WRT310N V1.I am trying to connect this via PPPoE to another Thompson router/modem that has been succesfully switched into BRIDGE mode.The Linksys router is conneted via ethernet cable to an ehternet port on the Thompson router.The ADSL cable is pluggedinto the WAN port of the Thomson 'bridge'.There is no cable in the WAN port of the Linksys router.
The Linksys router is set up to connect over PPPoE using the username and password that was given to me by my ISPs tech support (checked and double checked).The DHCP server on the Bridged Thomson is set to ON. DNS is set to OFF.the DHCP server on the Linksys router is set to ON.
View 2 Replies
View Related
Sep 20, 2012
I have been working on this for hours and getting frustrated! This router has been set up for over a year with no trouble, but recently had trouble connecting with my wireless devices and was kicking my wired (ethernet) laptop off when it is usually on all the time.
Now, my wired connection works through the router, the wireless devices all connect to the network but do not have access to theinternet. From the router's setup page, when I enter my PPPoE information and go to status and connect, it tries to connect a few times then gives me the error message 'cannot get IP address from PPPoE server"
I have tried updating firmware, resetting, restarting, recycling power, chat support with ISP and chat support with Linksys. Have verified my username and key and those are correct otherwise I'd have no internet access at all. I do have wired access but not wireless. The wired connection does go through the router.
Bridging - my modem is a bridging modem only, so it shouldn't be that.
View 4 Replies
View Related
Dec 22, 2012
I look forward to the new firmware can improve this problem.
View 3 Replies
View Related
Oct 31, 2011
I set up the router in our office and all is working well. BUT, when I have to FTP from my pc to our web server wich is at a typical web hosting company, now we are having time out issues, stalls, an closed sessions.Our server company checked everything and all is clear. I can FTP from outside my office (home) with no issuies at all. So this leads to the E3000 causing the issue. Simply everythign worked on Thursday, we installed on Friday and now we have the issue.
View 3 Replies
View Related
Jan 27, 2012
I have the E3000 and have attched a WD 1TB USB drive. I set it up for FTP and Media sharing and it worked fine but somehow recently I could not connect anymore. I checked the router and all of my setting for the FTP and Media server were gone. The disk drive still shows avaiable but now it shows the entire 1TB free (it was at least half used). This is the second time this has happened, first I tjhought it was a bad disk and replaced it but now it happened again. I did do a power cycle some time ago but I remember it still work after that. Not sure why I am losing my settings. This does not give me a comfort level as to storing anything valuable on that drive.
View 1 Replies
View Related
May 29, 2010
I have connected my LaCie rugged drive to the router and would like to use it as backup storage and as a way to stream video to my PS3.When I go to my advanced settings for the router and go to the storage heading I can see my LaCie and its specifications. There is a button next to it that says "claim", which I press, but nothing happens.I don't have the option to create a shared folder, and I can't access the drive from my Mac.On a somewhat related note, I've enabled the media server and can find it on my PS3, but there is nothing in the root folders. How do I put stuff (movies, music,etc.) into these root folders?
View 7 Replies
View Related
Jan 1, 2011
I just installed this router and connected the hard drive (Western Digital 1TB) which worked fine at first. When I moved some movie files to another folder they lost all of their data. The file names are still present, but all the media files show zero bytes and are no longer usable. Is there anyway to get these files back? I have been digitizing all our movies to the tune of about 90GB. What could be going on here? I disconnected the HD from the router and plugged directly into the laptop. Still shows the file names, but each file is still at zero bytes. Not a cool way to have a media server for your house!
View 6 Replies
View Related
Feb 19, 2012
Is there support for album art or video thumbnails in the UPNP media server on the E3000? I've tried adding jpg files with the same name as the video file, but I see nothing in the client. I've also tried naming them 'folder.jpg' and 'cover.jpg' but still get nothing. If this isn't supported is there any plan to add support in the future?
View 2 Replies
View Related
Nov 30, 2012
For the past few months, I have been using a Buffalo drive (formatted as FAT) as a media server to function as my network drive for iTunes. Unfortunately, I have recently noted in the last 2-3 weeks that, when copying new files, the file size changes to zero bytes. I do not seem to have this problem when i plug the drive directly into my computer via USB, only when adding files over the network. I spoke to tech support, who said, based on the story in that files can be correctly transferred when directly connected, it appears to be a network problem.
I am running OS 10.8 with iTunes 11 (but also occurred with iTunes 10) and using version 1.0.04 on the E3000.
View 1 Replies
View Related
Mar 16, 2011
I have been trying to connect my daughter's toshiba a215-54697 wirelessly to my linksys e3000 router. The computer recognizes the network wirelessly as the correct name and will only have "local access". When it is hardwired to the router it connects just fine, it also will connect to the unsecured (guest)network. I have comcast internet that is connected to an ooma box that is cconnected to the router. My laptop and the playstation find and connect to the internet just fine. The toshiba is running windows vista with a atheros ar5007eg adapter.
View 2 Replies
View Related
Apr 18, 2012
I've enabled the Media Server on my E3000 router. My PS3 can see the server and play media from it by my PCs can't!
I'm using Windows Media Player v 12.0 on Windows 7 and some older version on Windows XP and it's my understanding that the Media Server should appear under the "Other Libraries" section but it does not.
Am I doing something wrong? Is there a bug in the E3000 firmware (I have the latest as of this date) or is the Media Server simply not compatible with Windows Media Player? compatible media player for Windows 7?
I did read a post about a firmware upgrade on the 4200 that broke the media player, but I don't know if such a problem exists for the E3000.
View 1 Replies
View Related
Dec 24, 2010
There is one router ( SWR54BGA ), wan interface functional ( connected as a dhcp client to the lan interface of another router , packets are forwarded). When i connect the wan interface to the isp line, and provide the pppoe login details ,it won't work. When i try to connect manually to the pppoe server from the wan configuration page, after about 30 sec i get the connection failed message.Is the firmware corrupt, should i go the ddwrt route?
View 2 Replies
View Related
Sep 22, 2012
There are 2 ps3,a wii ,2 laptops,3 desktops,2 dsi.We have been having issues for a while now with losing connection and the service provider says there is nothing wrong. the modem is a comtrend ct-5072t and the router is a linksys E3000. The E3000 is the 3rd router I have bought in the last yr and 1/2 the last was a d-link dgl4500 gaming router the modem is new a rentel from the provider. Downloading updates for the ps3s are a nightmare online games like arma2 and battlefield 3 are a pain because we are losing connection all the time dont know what to do.
View 4 Replies
View Related
Jan 2, 2011
I bought a Linksys E3000 Router. I have hooked it up and connected my PS3, laptop, iPad, 2 guest laptops on occasion with no issues. However, my fiancee's laptop will not connect to the internet. It connects to the network fine, just not to the Internet. I keep getting the same error "Cannot communicate with Primary DNS Server". She is running Windows Vista SP 2. I tried all three of the solutions suggested by Vista, but they all failed. I also did a hard reset of the laptop, router, and modem. Waited a little while with everything unplugged. Still cannot connect to the interent and get the same error message.
View 14 Replies
View Related
Nov 17, 2012
I've been using my EA4500 since it's original launch date as a PPPoE router through another router/modem which is the Netgear DG834G V4 set to Modem Only mode which was working fine for a long time!A month ago, a friend wanted to borrow the Netgear Router and after he gave it back I reset it like I always do and entered my settings in router mode(i.e. username and password) to check if I havewe working Internet connection and that the router is working properly and it was working properly like it was before I lent it. Now comes the problem, if I keep using the Netgear router as the PPPoE handler and make the EA4500 work as "Automatic Configuration DHCP" it works flawlessly but if I set the Netgear router to modem mode and make the EA4500 handle the PPPoE connection, the report in the troubleshooting tab keeps on saying "Connecting" endlessly!
Note: I've replicatedthe settings that I used on both router before and after lending it to my friend so there's no difference in settings!
View 6 Replies
View Related
Dec 27, 2012
I extremely need PPPoE Dual-Access on my EA6500.I'v paid $225 and can't watch IPTV So, I'm somewhat disappointed with tis issue...
View 9 Replies
View Related
Oct 4, 2012
I was assigned a static block over PPPoE from the ISP. I can connect to the internet using the gateway address but I need to route the other static IPs to my servers. I might say that I accomplished it on a couple of older routers - E1200 & WRT120N, but I cannot get it to work on my new EA3500. I have 5 usable IPs plus the gateway IP that is assigned with the PPPoE connection on the WAN port.
View 8 Replies
View Related
Aug 2, 2011
I have a WRT54GS wireless router. I can successfully set up the router with my DSL modem for PPPoE. Here's my problem. The router configuration requires you to put in the userID and password, then logs you in to your ISP automatically. I DON'T want it to do that. Is there any way to configure for PPPoE where ISP login is controlled manually; i.e., when the user tries to connect to a web page, a dialog pops up for entering the password?
View 1 Replies
View Related
Oct 24, 2012
When the ethernet cable is plugged directly into my laptop i can input my user name and password and connect directly without a problem. But as soon as i plug the cable into the router, the activity lights turn off like its not plugged in on the other end...which it is. So when going through the setup process, both using the cd and inputting the information on the web based setup. It does nothing, the automatic setup says the cable isnt plugged in. When using the browser setup i can click connect as many times as i want and it does nothing but say disconnected.
View 9 Replies
View Related
Feb 18, 2012
I am using wrt54gx4. I have a IP camera connected to it. I can view the live images on the intranet and internet. Not too long ago my DSL company upgraded my DSL modem to a newer model. Then I can not connect to the internet by PPPoe. DHCP is fine. So the only connection type works is DHCP. But now I can not view the live images on the internet. I can only view the live images on intranet( I mean if I open web browser and type url.. is the port, I can view the live image).
View 1 Replies
View Related
Dec 13, 2012
I have a Cisco/Linksys E2500 router that I have had for over a year and it has worked without issues for over a year. However my wireless ISP just switched my CPE from A Mikrotik wireless radio to a Ubiquiti wireless radio. As soon as they did this my PPPOE sessions from the E2500 (acting as my PPPOE client) start disconnecting and reconnecting every few minutes causing major problems with my internet and voip connectivity when it looses connectivity every few minutes.
The strange things is if I connect my much older WRT54G router as a PPPOE client (with the same exact PPPOE configuration), it works just fine and I don't have any PPPOE disconnects.
I upgraded to the latest firmware on my E2500 and nothing changed, it still disconnects my PPPOE sessions probably close to 50 or 100 times an hour.
I'm thinking it's some sort of compatibility issue between the Ubiquiti Nanobridge Radio CPE and the E2500 router acting as my PPPOE client. Also another thought was that perhaps my ethernet port wasn't negotiating speed/duplex correctly on the E2500.
Is there any way to hard code the speed/duplex on an E2500? I can't seem to find any spot with that setting.
View 8 Replies
View Related
Aug 11, 2010
I have configure pppoe on my WRT120N it say it's connected but cannot access wan side of the router.
View 5 Replies
View Related
Jan 24, 2013
I have a Linksys E1000 router just upgrade to the latest 2.1.0.2 firmware...I have a PPPoE connection which used to run smoothly on the router..however off late...suddenly the router stopped connecting..it always shows "connecting" in the status tab of the router page...and eventually says failed to obtain IP address...however when I attach the cable directly into my PC it works just fine.I also had a word with my internet provider...he's kept the MAC open (or something like that) so he said that isn't the issue and he keeps saying there must be some issue with the router. However, occasionally the router DOES connect for half hour or so and then just refuses to connect again !..
View 2 Replies
View Related
Jun 20, 2012
New E900 router drops PPPoE session and gets new IP address randomly every 1-20 hours. Tried different E900, does the same thing. Disabled IPv6, no change. Upgraded FW from 1.0.00 to 1.0.01, no change. I have an SPA112 ATA behind the router and it has to re-register with the VoIP provider every time the IP address changes, so I'm afraid of my call getting dropped if this occurs while I'm on the phone. Using an old WRT54G or a different brand of router it will keep the same PPPoE session for weeks, so it is not the ISP.
View 2 Replies
View Related
Nov 29, 2012
I recently buyed a Linksys EA6500 wireless router. I accessed [URL] to access the settings interface of the router. Went to "Connectivity Internet Settings" and chose type of the internet connection as PPPoE. Entered the username and password, clicked ok.
No internet access.
View 9 Replies
View Related
Feb 7, 2013
Have a v2 E1200. Connect with PPPoE to ISP. IPv4 works fine. With firmware included on router, 2.0.01, it would receive a /64 of IPv6 from the ISP. This /64 would show up under 'status' / 'local network'. Although it did not seem to advertise this space to PC's on my network so I was unable to use it. I updated firmware to 2.0.04. Now it does not even pick up the IPv6 /64 at all.
Anyone have PPPoE and IPv6 working? Anywhere I can download 2.0.01 to try it again?
Is there a model of router that actually works with IPv6?
View 2 Replies
View Related
May 23, 2011
We have WLC-4402 and LWAP-1510, we have issue when users trying to connect to pppoe server with pppoe connection from wireless network. On LAN, pppoe connection work properly and everything is normal. Also I enable broadcast fowarding on GUI but he problem still exist.
View 1 Replies
View Related
Oct 13, 2011
I am using the WRT54G2 connected to a cable modem that requires a PPPoE login. I followed the Service Providers instructions and cloned the modems MAC address to the WRT54G and setup the PPPoE user id and password. I can then plug my PC into one of the Ethernet connections on the back of the WRT54G and everything works as expected. First I connect to the WRT54G2 and then I open a PPPoE connection in my network settings and it logs into the service provider and everything works as expected. But when I connect to the WRT5G2 wirelessly I connect to the AP fine. When I open the same PPPoE connection to the service provider it fails, the message says I have the wrong userid or password or that the protocol is not supported. Of course I know the userid and password is correct because it works when connected with Ethernet cable. I have tried disabling the security on the wireless network but that did not seem to work.The modem is a HomePNA HCNA Voice Endpoint.I am at the latest firmware 1.0.04.
View 7 Replies
View Related
