I'm planning to deploy PPPoE Server (Cisco Router 7609) for an ISP. This ISP will provide Internet connection for customer over Ethernet (QinQ VLAN).I have to provide a solution to assign bandwidth to each customer by RADIUS. I found some documents about this function but they said that it could work with PPPoA or PPPoE over ATM only. So which method I shoud deploy to get this goal?
View 1 RepliesI'm planning to deploy PPPoE Server (Cisco Router 7609) for an ISP. This ISP will provide Internet connection for customer over Ethernet (QinQ VLAN).I have to provide a solution to assign bandwidth to each customer by RADIUS. I found some documents about this function but they said that it could work with PPPoA or PPPoE over ATM only. So which method I shoud deploy to get this goal?
View 1 Replies View RelatedOur subscriber is suffering from bug CSCti52867. The file system check repairs errors but we are still experiencing the read-only file system. We can ssh into sub but there is no prompt to enter commands. None of the services are started so there is no web interface. Firmware update cd updated firmware to 3.6 but problem still exists.We have successful backups from pub. How to reinstall/restore sub after hardware failure? This is the first time I've ever had to work with dr.
View 5 Replies View RelatedI have a ZyXel P-660R-D1 DSL modem, and lately I've been experiencing random outages. I'm not super knowledgeable when it comes to the technical side of networking, but I know enough to look around the modems GUI and recognize when something isn't right. I'm pretty sure this is not a problem on my end, but I'd like to hear a few other peoples opinions. Basically I have four lights on the modem: Power, Ethernet, DSL, and Internet. DSL is the light that indicates connection to the PPPoE server, and lately it will just randomly drop. I've never experienced problems connecting with the PPPoE server until just recently. Every once in a while my Internet light will drop, and a simple reset will take care of it, but rarely am I ever not connected to the PPPoE server. One day it was down for three or so hours, one day for nine, another day it cut in and out for about four hours, and today was another nine hour day. how it works is that my username and password are verified through the ISPs PPPoE server, and then I am granted access to the web. I'm lead to believe that it's nothing on my end because all troubleshooting methods fail, it just randomly fixes itself several hours later. The first nine hour stretch I experienced I thought may have been because of maintenance or some other unforeseen circumstance, but it has happened a few times now so I'm not too sure. My provider, Earthlink, hasn't listed any 'Known Outages' on their site, but then again they never do.
View 1 Replies View RelatedCan we assign Secondary ISP-2 Pool IP to DMZ Server, network design attached for reference.
View 2 Replies View RelatedI have 3 external ips from my isp:
222.222.222.221
222.222.222.222
222.222.222.223
The first one I use to provide internet access to my office. The other two I'm going to use for the following: I'm going to deploy a server in internal network which must have 2 external ips on his network interface (& one internal ip on the second,but that's ok: I cannot put an extra network switch before asa & plug this server there: this server is virtual & is on esxi host in internal network. External ips must be assigned to servers' interfacw,bot just forwarded there (ms direct access requirement).
My current config:
!
ASA Version 8.4(3)
!
hostname msk-office
[Code]....
I haven't been able to subscribe to any internet subscriber. There happens to be a network in my area which is unlocked (linksys) i usually get 1 bar of signal 2 if I'm lucky. Even with 1 bar I'm able to stream video on my xbox while using my laptop. Well every couple weeks or so, the signal disappears, sometimes showing up for just a few seconds and than it eventually returns and we use for another couple weeks. I've considered maybe whoever owns the signal isn't paying their bill on time but the time frames wouldn't make sense.
View 1 Replies View RelatedI imagine I can use the framed-ip-address attribute to assign ip-addresses but there seem to be support for static ip addresses only?A bit of a drag when we're talking 200+ nodes.
View 1 Replies View RelatedI´m trying to configure SR520 Cisco router as PPPoE server. The point is, when configuration is done and PPPoE client is directly connected to the interface, SR520 doesn´t respond to incoming PADI. PADI is not shown in PPPoE debugs (debug pppoe events, packets and errors).On the other hand, I get the PADI capturing packets with wireshark (so PADI is being sent) and the same configuration on other router works fine.
View 2 Replies View RelatedI am working to test the PPPoE solution. The requirement is that she like to have a PPPoE server (7200), enable the DHCP pool on the router. The PPPoE client (1811) should receive the IP address through the DHCP and with subnet mask (/24) so that routing protocol can enable between the PPPoE server and client.We test with some initial configuration but not success to obtain DHCP address from the pool.
On PPPoE server router,
!
ip dhcp pool DHCP-PPP
network 192.168.254.0 255.255.255.0
default-router 192.168.254.254
[Code]...
I have a RVS4000 router with DHCP enabled and in router mode.
The LAN is 192.168.2.x. The RVS4000 static IP address is 192.168.2.8
The router is not the RVS4000 and is at 192.168.2.1
The RVS4000 dhcp is assigning it's clients a default gateway of 192.168.2.8 instead of what I want 192.168.2.1. How can I get the RVS4000's DHCP server to assign another IP address other than its own as the default gateway to its DHCP clients?
There is one router ( SWR54BGA ), wan interface functional ( connected as a dhcp client to the lan interface of another router , packets are forwarded). When i connect the wan interface to the isp line, and provide the pppoe login details ,it won't work. When i try to connect manually to the pppoe server from the wan configuration page, after about 30 sec i get the connection failed message.Is the firmware corrupt, should i go the ddwrt route?
View 2 Replies View RelatedIt took a while of troubleshooting since I've never ran into this problem with my wireless router before. But finally I figured out that my router will not assign the proper DNS server addresses when assigning through DHCP. I upgraded from 2.10.02 and still the same issue.
View 1 Replies View RelatedI installed a Linksys WRT54G2 router earlier this year and set my Siemens modem from AT&T(Actually from SBC before the two merged) in bridge mode. I did this so I could change the NAT setting on our internet, which was interfering with my Xbox. It worked for about 4 or 5 months with little to no problems. Recently, however, the internet has been disconnecting and when I check the status page on the router it says it is disconnected. Sometimes clicking on the connect button will work, but usually it will say "Connecting" and keep refreshing the page for a little while without any change, then give me a message saying it couldn't get the IP from the PPPoe server. Turning it and the Siemens modem on and off and fiddling around seems to solve the problem, but only temporarily. Interestingly enough, I don't think it ever interferes with my Xbox. Until recently, the Xbox was set as the highest priority on the QoS page, but I changed the computer to the highest priority and it hasn't worked. In addition, the small, thin green light bar just below the Linksys logo on the top of the router has just recently started changing to orange occasionally
View 9 Replies View RelatedI have a Linksys WRT310N V1.I am trying to connect this via PPPoE to another Thompson router/modem that has been succesfully switched into BRIDGE mode.The Linksys router is conneted via ethernet cable to an ehternet port on the Thompson router.The ADSL cable is pluggedinto the WAN port of the Thomson 'bridge'.There is no cable in the WAN port of the Linksys router.
The Linksys router is set up to connect over PPPoE using the username and password that was given to me by my ISPs tech support (checked and double checked).The DHCP server on the Bridged Thomson is set to ON. DNS is set to OFF.the DHCP server on the Linksys router is set to ON.
I recently bought an E3000. I am trying to setup a wireless home network.Google and tried a lotta things (power cycle the most no. of times ). Nothing worked.So I poked around. Looked up the IPConfig of my PC with wire connected directly(no router), was 192.168.0.xxx. So I hit 192.168.0.1 in my browser address bar, and it came up with the login page for a D-Link DIR600. A wireless router with wireless disabled. Apparently this is being used as a switch by my ISP. This I know cause I checked the active connections and DHCP reservations on the D link and it showed up about 100 different PC's (including MAC and IP addresses).
View 9 Replies View RelatedI have two DIR-615 devices, I want use first device for main AP and DHCP server and PPPoE . And use second device for Repeater.
How to work WPS and Push button on this device.
I upgraded my SG500 switch firmware to 1.3.0.59, since there is a new functionality DHCP server v.4 well I must say I came accross the issue I cannot solve. DHCP server assign dynamic address - no hassles. troubles start with static IP hosts.I defined a couple of hosts with static address within the correct subnet. I tried with hardware address and client identifiers. no luck. my switch does not assign the IP address I assigned to the suitable mac address. to define it I use both CLI & Web.
ip dhcp pool host HP-Elliteaddress 10.10.11.7 255.255.255.0 client-identifier 01:d8:d3:85:cf:09:72client-name HP-Ellitedefault-router 10.10.11.1exit
ip dhcp pool host VAIO-Zaddress 10.10.14.108 255.255.255.0 hardware-address 54:53:ed:1c:a1:46
default-router 10.10.14.1exit
I am using a RV016 (192.168.1.2) as a router and DHCP. It automatically assigns its own IP which is 192.168.1.2. I can not set my RV016 to assign a Default Gateway IP of the server. The workstations will connect to internet via this server (192.168.1.1)
View 1 Replies View RelatedWe have WLC-4402 and LWAP-1510, we have issue when users trying to connect to pppoe server with pppoe connection from wireless network. On LAN, pppoe connection work properly and everything is normal. Also I enable broadcast fowarding on GUI but he problem still exist.
View 1 Replies View RelatedHow do i get the 12.4 code to assign a dhcp address to my ethernet interface from my server? I deleted the default config on the 1141 and searching has not turned up anything useful.
View 1 Replies View RelatedI have been working on this for hours and getting frustrated! This router has been set up for over a year with no trouble, but recently had trouble connecting with my wireless devices and was kicking my wired (ethernet) laptop off when it is usually on all the time.
Now, my wired connection works through the router, the wireless devices all connect to the network but do not have access to theinternet. From the router's setup page, when I enter my PPPoE information and go to status and connect, it tries to connect a few times then gives me the error message 'cannot get IP address from PPPoE server"
I have tried updating firmware, resetting, restarting, recycling power, chat support with ISP and chat support with Linksys. Have verified my username and key and those are correct otherwise I'd have no internet access at all. I do have wired access but not wireless. The wired connection does go through the router.
Bridging - my modem is a bridging modem only, so it shouldn't be that.
I look forward to the new firmware can improve this problem.
View 3 Replies View RelatedIs it possible to assign IP addresses to remote site WIFI users from local DHCP server and forward all other traffic to 2504 WLC?
[WIFI Users] >--------<AP (DHCP server) >------ VPN ---------< WLC
I am using a win server 2008 in my company, recently my staff have being using internet a lot for downloading and many other unnecessary software therby redusing overall bandwidth.Is there any software solution i can use for controlling bandwidth of my client computer from server2008 computer.
View 3 Replies View RelatedI have an Ubuntu Server, when someone is downloading a file from it, my bandwidth significantly decreases, how can I cap it?
View 5 Replies View RelatedWe have 1 mpbs bandwidth line, but most of the time we are getting only 300-500 kpbs download speed, i want to send statistics report to our ISP, what will be best procedure to test the bandwidth report, i have checked in some websites like bandwidthplace and speedtest but these sites are not accurate, how to check the actual bandwidth we getting from ISP against 1 Mbps. We have solarwinds monitoring tool in this i have configured the WAN interface for 1 mbps
View 5 Replies View RelatedI have a scenario with 2 7609s connected through a MPLS service with 10 GE. In each7609 we have a 24 port channelized T1 Circuit Emulation Over Card.
The requirement is in 2 parts. First, we need to provide a T1 emulation service between the 2 7609s T1 cards.
The second requirement is that in one end there is an OC3 port, so the customer wants to send the traffic from this emulated T1 onto the OC3.
I am currently setting up a new VRF on a Cisco 7609 which is advertising (as a RR-Client) an iBGP route to a Juniper MX960. This route is then getting sent back to the default route table on the 7609 but rejected due to the cluster-id loop prevention. Although not ideal I need this route to be visible in both tables.Is there a way of changing the bgp cluster-id per VRF rather than just globally?
View 2 Replies View RelatedWhat are the prerequisites before doing this? I have to upgrade a router this week if there is an opportunity to move it to a code that is more current that the one the client is currently running which is 12.2(33)SRD4. I see on the Cisco Support site that after this code, everything moves to 15.
View 2 Replies View RelatedWe have a router 7609 with Supervisor Engine 720 (WS-SUP720-3B) (Policy Feature Card 3 and MSFC3 Daughterboard) and We have to configure QoS over a FastEthernet interface on a WS-X6148-RJ-45. When I try to apply the policy command I get the next log:
#service-policy output TEST_QOSbandwidth percent command is not supported in output direction for this interfaceConfiguration failed on: FastEthernet1/2 What kind of hardware and software requirements I need on my router to perfom QoS over ethernet interfaces?
Configuring MPLS over GRE tunnels. I did not find any proper configuration example. I need to do this for encrypt the traffic between two PE routers. I have 7609 routers.
View 20 Replies View RelatedI have a hight CPU utilisation problem in my CISCO7609-S routers. the cpu utilisation can rise 99% et this is usually. In the moment of hight CPU the the process CPU give the following:
the show processe cpu history give: show version