so i want to move my dns and dhcp to a server (sbs2011). i am currently using a netgear 3700. i am a little confused on how to set this up. i know to turn off dhcp on the router. will the server give out a dns address? do i even need to router, or could i just use a switch?
View 1 Replies
How could I add an AP 1522 ag without DHCP. How do I setup the IP address configuration? For some electrical problem I lost 4 1522 APs. I have two controllers and a windows server running WCS. Now I have just one AP up and running. After booting a new AP I could not get in "config mode" via console so I tryied to setup the IP config as follows (pressing ESC key during the boot):
set IP_ADDR 10.1.1.100
set NETMASK 255.255.255.0
set DEFAULT_ROUTER 10.1.1.1.1
then: "boot"
*** I have authorized the new AP in "MAC address filtering" via WCS.
*WCS version 7.0.164.0
I think that is no request reaching the controllers.
This is on a DIR-655, firmware 2.01NA, hardware rev B1.Is there a limit on the number of DHCP reservations that can be added to this WAP?This WAP was working fine with 10 DHCP reservations (wired & wireless devices), 6 schedules, Access control of 2 devices by MAC (6 defined, only 2-3 active at a time).I started adding additional DHCP reservations, because I'm simplifiying my network, and when I add the 26th DHCP reservation I get the message "Schedule rules is Full! Please Delete an Entry."
I've been adding all of the new DHCP reservations as disabled, but I haven't assigned any schedules or otherwise to these new devices yet. So what's up with this message??
I have a very simple setup containing 3 C2960S switches:switch 1: central switch, acting as router between VLAN 1 en VLAN 2switch 2+3: edge switches, connected via 1 link to central switch, both on VLAN 2,Clients connect to switch 2 and 3 using dhcp, switch 1 uses dhcp relay to forward requests from VLAN 2 to the dhcp server on VLAN 1. So far so good.Now I want switch 1 to add option 82 to the dhcp requests so the dhcp server can see whether the request came through switch 2 or switch 3. I tried turning on dhcp option 82 support on switch 1 by doing.
View 2 Replies View RelatedThe company I work for owns a remote manufacturing facility that houses a stack of five 3750 switches that function as the core switching system for the plant. DHCP services are configured on the 3750 stack.
There are currently three VLANs configured, one for data and one for voice (144 and 244 respectively) and one for UCM servers (200), with corresponding subnets of 10.44.32.0 /19, 10.44.0.0 /19 and 10.44.100.0 /24.
The current DHCP scope configurations are as follows:
ip dhcp pool Plant-44_DHCP
network 10.44.32.0 255.255.224.0
default-router 10.44.33.254
[Code].....
My question is will the addition of this scope in the manner presented cause any problems with PCs or IP phones outside the targeted recepents receiving the wrong IP information from this scope?
I plan to identify the users that should be members of this VLAN 444 and change the switchport mode access configuration on the corresponding switch ports from VLAN 144 to VLAN 444. The voice VLAN 244 will remain the same.
I have two 5508 controllers configured with an internal dhcp scope. The scopes on each controller are a /22. I need to expand the scope to provide more addresses. Is there an easy way to add a second dhcp scope without making changes to the existing scope? If so how will the clients devices be able to access that ip address range?
View 1 Replies View RelatedI just had comcast business class installed. They installed a SMC d3g router. It does not support nat loopback. I had a server installed and could not browse to it inside the lan because of this issue. I was instructed that I needed to set the the servers IP to the external address and open the ports to that. That worked, and I added an internal address 10.1.10.x so that I could see it inside the firewall. The issue that I am having is that since I did this, the server can not be seen by the macs and the mac shares don;t show up for them.
View 4 Replies View Relatedi am facing the same problem now but am using windows 2003 server
View 1 Replies View RelatedI work in a small group with a network server so we can share files and documents from computer to computer. I am trying to access this server on a new computer and am not having any luck finding instructions on how to do so. I don't need to sign in to the network (to gain access to internet browser, etc), I need to be able to add this computer to our server so I can view these folders & files on this new computer.
View 2 Replies View RelatedI have a pair of managers in HA mode and a pair of servers in HA mode. The solution is working in OOB Virtual Gateway. When i add the server in the manager, which IP address must i use, the service IP address or the physical Ip address.I'm running 4.8.2
View 2 Replies View Related[code]...
I am able to obtain IP addresses through the DHCP server for my clients and I am able to browse internet on the server 2k8.Server 2008 - Share Internet through DHCP server
At my office we have a dell server running windows small business server 2003, there are around 15 computers on our network running mostly windows 7 (a few with XP). I am wondering how difficult it is to add a computer to the network so it can log into our domain and all that.I just had to reformat one of the computers and would normally wait for our network guy to do it remotely but If i could do it myself it would save time (and money). I am already an administrator and basically i just need to make it so the log in prompt when windows starts has our office network listed as the domain instead of jus the local log in. It is a dell running windows 7 64 bit.
View 5 Replies View RelatedWhat kind of feature set of IOS for NAT. I need it for my Cisco 3700 router.
View 2 Replies View RelatedHow to forward Port 123 on this router?
View 4 Replies View RelatedI have a dell vostro 3700 and have had it for about 3 years with no problems. Lately it has been picky on when it will let me use my home wifi it will say "restricted use". Then today it stop working all together and says that no network connections are available, but they are because everyone else's computers in my house are working.
View 3 Replies View RelatedI am not able to disable rate limit comand from Cisco 3700 series router. I have tried with no rate limit command in the interface .Command is taking but still the rate limit comman in the interface.
View 2 Replies View RelatedI bought a Vostro 3700 which i formatted and installed windows 7 using the CD which came with the laptop. I used the drivers CD which also came with the laptop to install the drivers but i am still having trouble with the network controller. On the device manager list it still says its not intalled and as a result i have been unable to use the wireless. When i try to install the wireless drivers an error message comes up saying no compatible hardware found, but the wireless worked fine before the format!
View 15 Replies View RelatedIs there any tool or script which will automatically generate scripts for routers, switches. I am configuring 100's of cisco 3700 routers and 3500 switches. I want to be consistent with my configuration . I am looking for script that when u run it, it will prompt you step by step to configure router, and switch and generate router config file. I know aobut cisco autoconfig maker but thats not what i am looking for.
View 2 Replies View RelatedI am working w/ WNDR3700, and I've been trying to take a look at the traffic meter to judge how much I actually us.
In 7 days I supposedly already used 30gig. There are only two computers to the network and the most we do is Pandora/gaming. Is this router incorrectly reading incoming/outgoing data? Is there someone logging into my router and downloading freaking porn or something? Because whenever I check to see connected devices, I only see our comps, are they able to hide their device on the router?
This month
153:58 Upload/Avg=2,562/366.03 Download/Avg=30,228/4,318 Total/Avg=32,790/4,684
The most I do on the web is schoolwork/pandora and play league of legends or counter strike.
The only difference I can see is the 3700 has gigabit ports. Any other performance differences about with these two routers? I already have the 3400 but I am wondering if I chose the wrong router seeing as the 3700 is only ten bucks more. What there experiences were or there knowledge of these two products or even opinions. I have a gaming PC hard wired, ps3 wireless, nexus 7 wireless, and LG Media Player wireless in a 1400 square foot house with one wall between ps3 and 2 walls between media player. I doubt range will be an issue with either routers though. I might transfer files between PC's later on but 10/100 should still be pretty good speed or not so much?
View 3 Replies View RelatedI bought this wireless router about a year+ ago, and it's just great. It's attached to the cable modem "downstairs" and right now it supports 2 smartphones wirelessly plus an ancient wired cable to an "upstairs" home office.
I'd like to improve overall performance with a wireless bridge to a gigabit hub in the upstairs office. I'd also like to add a second wireless bridge so I can stream movies to a box that would be attached to my TV, which does not have built-in wireless access.
Trendnet seems to have some interesting wireless bridges, but in the past I had a Trendnet wireless router with really, reallly bad software.
I had to re-install Windows 7 -64bit after my hard drive had crashed, but I can seem to get the Wireless to work. I tried following the installation order as per the following link but I couldn't install the NSS/DSS as I could not find this download for my Vostro 3700. I also read somewhere that it is not needed for Windows 7, so I left it.
I installed the WLAN 1501 Half Mini-Card (4313bgn) (R270598) driver as this is the wireless card that I have and it installs. The problem I have is that the wireless software and windows says my wireless card's radio is disabled and that I need to switch the radio on using the switch on the laptop. This laptop has a physical switch and no matter if I turn it on or off.. the radio remains off. Even the wireless light above the keyboard does not switch on.The thing is, before the hard drive crashed, my wireless worked fine. Is it possible that the switch broke too, or am I missing some kind of driver or software for the wireless switch.
Looking for the most efficient setup of my home network. I recently bought the netgear 3700 and it has been great. I also have a trendnet green 8 port giga switch. Both of these will be located in my equipment closet.
I also have an ooma voip hub. before i did the router upgrade i had modem>ooma hub>router. Mainly had it that way since the previous router was a wrg614 and i thought the hub probably had better qos routing. I now have the 3700 infront since i think it does that. I need to learn how to setup the qos though. Problem is that having the hub after the router loses one of my 11 ports (i have pleanty now).
Will speed through the switch be as fast as straight from the router? should my netflix devices connect directly to the router or does any of this matter. [code]
Had a WNDR 3700, as I do, and replaced it with a 4500 and whether it was worth the upgrade.I can always use the 3700 as a wireless repeater in the living room, where I kind a need one anyway.
View 7 Replies View RelatedI have a connection between HQ and Branch which connected by GRE tunnel over IPSec. I use Cisco router 3745 that has IOS version: 12.3(18) and Cisco router 2911 that has IOS version : 15.0(1r)M9 with ipbase, security and data license.
I tried to apply command to both routers as follows:
Cisco 3745 (HQ)
crypto isakmp key test address 10.1.1.2
crypto isakmp keepalive 60
crypto ipsec transform-set myset esp-3des esp-md5-hmac
crypto map vpn01 local-address Loopback0
[code]....
When I appied this command that will show a notification as below:
NOTE: crypto map is configured on tunnel interface. Currently only GDOI crypto map is supported on tunnel interface.
*** After appied this command, I cannot ping or send any traffic to HQ. ***
I use this command that is working normally on Cisco router 3745 that has IOS version: 12.3(18) and Cisco router 2811 that has IOS version : 12.4(7b).
My config:
Windows 7 host
MS Loopback Adapter with ICS
GNS3
ASA 8.42 with ASDM 6.4
Vmware Workstation 7 with Windows XP SP3 vm
All are working like a charm, from my virtual XP machine I can ping every site, e.g. www.google.com which replies nice with it's ip-address.
However, I cannot reach ANY website
When I connect through a Cisco 3700 router the webbrowser works perfect, so it must be something in the ASA configuration (I presume )
I've tried about all possible Access Rules, but still nothing.
anyways here is my concern, we have a DHCP server in our company (HOTEL) and the Computer wont turn on, the computer is Compact Proliant Intel Inside Pentium Pro Processor OS Windows Server 2003, this Computer is so old. they been using this for 12 yrs and they didn't upgrade... now its dead.
since this Computer wont turn on, all of the computers cannot access in the internet, so for the meantime this is what I did... from the modem to router, I configure the router as a STATIC IP and I enter the IP address provided by our Internet Service Provider after that all of the computers form the hotel have internet connection.
now I'm planning to build a new PC and set up a DHCP server but I don't know how and where to start
OLD Dell computer running Windows XP Professional. Just ran a clean install and installed new drivers yesterday. After installing Service Pack 2, I began getting limited connectivity errors. Tried ipconfig/release and ipconfig/renew, but received the DHCP error.
View 6 Replies View Relatedsetting up a DHCP server on a Cisco Layer 3 Switch. How would I set the pool up to issue the lowest available IP address all the time. At the moment it counts up even if a lease has expired.
View 12 Replies View RelatedI cant find the v LAN-membership command on my 3700 layer 3 switch, I've searched Google on whether the command has upgraded to a new syntax to no avail, I'm using GNS3 and the IOS is c3725-adventerprisek9-mz.124-25d.bin
View 4 Replies View Related2 dhcp server on the same lan segment not thesame ip add series , how can i prevent to lease ip from another ip series
View 2 Replies View RelatedI'm trying to enable dhcp server on it. done this how to [URL] It works, but unfortunately the client takes almost 2 min to get an ip.
View 3 Replies View RelatedI've made hotspot ad hoc and then my client try to connect my hotspot but it must setting manually...how to my client connect to my hotspot automatically not manually??? and how to install and setup dhcp server i windows 7...
View 6 Replies View Related
