I am testing out some inspection options on an ASA 5505, and I am running into a situation in which applying a http inspection is dropping all outbound http traffic. I get a "protocol violation" error in the logs.
Here is the setup: I'm not sure why the web traffic is getting dropped.
policy-map type inspect dns preset_dns_map parameters message-length maximum client auto
I have deployed a cisco 2504 wireless controller along with four (04) lightweight access points (1041N) in four floors respectivly. The clients connect to the AP which is deployed in the lowest floor have regular timeouts/packet drops. Further this particular ap operates at channel 11 and it has around 11-13 rough access points in the same area and operates in channels such as 1,3,6,9,11. The DCA (dynamic channel allocation) is set to auto in the WLC. Further each ap has maximum of 07 -10 clients at any given time and I have changed this particular ap and checked still the result is same hence there is nothing wrong with the ap.
why the QoS deployment causes ports on 2960 switches to drop packets although there is no bandwidth contension? (output bit/second of the interface)packet drops at threshold 1, queue 2 ( queue 3 in config)
We are using Catalyst 2960 switches and are experiencing issues with QoS. After the QoS, we experience a lot of packet drops and it make the network slow. It appears that the slow performance relates to the egress queuing of each port.
Cisco IOS Software, C2960 Software (C2960-LANBASEK9-M), Version 12.2(50)SE5 WS-C2960-48TT-L
switch_06#show inter fa0/1 | in drops|queue|output input flow-control is off, output flow-control is unsupported Last input never, output 00:00:01, output hang never
I'm using a Catalyst 4948. It seems to drop all truncated packets. I don't know whether this is an expected behavior.I'm developing a program which processes packets in the following steps:
1) capture packets 2) if a packet is too long, truncate it to a certain length 3) insert a vlan tag (say 100) to each packet 4) send them to the switch
Mac address learning is disabled on the vlan 100, so the packets should be seen at all ports of the vlan. However, I only observed untruncated packets. Truncated packets seemed to be dropped by the switch.The summary of the source port is:
Almost no packets were output.I see a Cisco document says "ingress port drops corrupted packets" [URL] then my questions are:
1) Is this the root cause of dropping truncated packets?
2) What criteria does a switch use to check corrupted packets? My understanding is that truncated packets could have wrong L3 and L4 data, but they can't be detected at L2.
3) If switch drops mal-format packets, can we disable this feature?
WiFi drops 80% packets from new computers (Win7, IPv4 andIPv6 enabled) to reliable internet hosts. WiFi is OK (0% loss) from new computers to E1200 itself (ping E1200 IP address).Old computers, mobile devices, and wired are OK to reliable internet hosts.Basic Wireless Settings are Mixed, Auto Channel Width. Wireless Security is set to WPA2/WPA Mixed Mode. Guest Access enabled.
Two days ago, we changed our old 525 with asa 5520 ( ver 8.2 ). Configuration is the same, except the version. It even retains the same global interface and static public ip address as the old device.All worked well during that period.
Yesterday, one of the http applications , not tested other day, was found not to be working. To test, we switched back to the old 525 , however nothing was working when we did that.
Two days ago, we changed our old 525 with asa 5520 ( ver 8.2 ). Configuration is the same, except the version. It even retains the same global interface and static public ip address as the old device.All worked well during that period.Yesterday, one of the http applications , not tested other day, was found not to be working. To test, we switched back to the old 525 , however nothing was working when we did that.Does the static statement which actually does the translation for this application carry any arp problems or so.how can i check this problem.
when I connect to VPN with ASA 5510, can not connect to web applications in HTTP instead https in other applications are working properly. how can I fix this?
We're getting this error message randomly when surfing the Internet. We have websense running on our network to perform web content filtering and are using the ASA for the http/https redirects. We've contacted websense and they said this error message is coming from the ASA, not their product.
i would like to use ISP2 for all http/https/ftp traffic.how could I force my ASA to set a different gateway for http/https/ftp traffic ?i have tried several solutions such as nat/pat rules, nothing seems to work.
I just upgraded my ASA 5585 cluster from 8.2 to 8.4. I also upgraded the asdm .bin from 6.35 to 6.43. after rebooter the cluster, I try to access it with ASDM installed on my computer but it blocked at 17%.I tried to access [URL] but I just an error (with IE & FF) [code] What did I miss in the ocnfiguration ? I precise that I never used the http page, I already had the ASDM installed from another ASA.
I am replacing an old Fw with a New ASA 5510 and I have a problem with a TCP Connection on My LAN InterfaceI joined a picture of what I want to do. [code] From the PC,I can Ping the Video Camera But I can't connect to it with HTTP.I don't understand, Packet Tracert allow the Http packet too. [code]
configure my ASA 5505. It is setup using PPPoE. What I want to do is this:
I have one of my IP addresses (99.23.119.78) setup for ftp using the ftp protocol to our internal IP address 192.168.1.3. What I need is to also allow for HTTP access but not just that, I need it to forward the http port to port 9000 because the web interface requires port 9000 for customer access. Previously on our old firewall customers were able to access the web interface by browsing to [URL]. I would like to not have to not require the port in the URL.
In addition, I would like to be able to setup a different IP address in our range (99.23.119.73) to be setup for http access using the standard port 80 for the same internal IP address (192.168.1.3). This URL will allow us to access the administration web interface for the FTP server.
Here is my current config:
Result of the command: "show running-config" : Saved:ASA Version 8.2(1) !hostname ciscoasaenable password qVQaNBP31RadYDLM encryptedpasswd 2KFQnbNIdI.2KYOU
I am configuring a new ASA 5510 to replace a SonicWall and I have a problem with an HTTP Connection inside my LAN.PC from the LAN ( using ASA LAN interface as gateway) can't Connect to a Camera video Web Server (192.168.4.20) on Port 80 whereas I can Ping it.
ADSM logs show :
106015# Deny TCP (no connection) from ip1 to ip2 Flags RST on Interface LAN.The adaptive security appliance discarded a TCP Packet that has no Associated connection in the adaptive security appliance Connection table.
- I Enabled command "same-security-traffic permit intra-interface"
- HTTP inspection is disabled.
I used Capture feature on the Ingress Interface, I joined the Logs and a part of my ASA Running Config.
I am having an issue where the ASA is dropping packets on the vlan interfaces. I have it as a dedicated router/firewall for a 100mb connection .
Vlan1 is the internal networkVlan2 is the network to cable modem
Eth 0/1 is connected to a 2960G switch with hard coded 100mb Full Duplex at each end, this is the inside interface. Eth 0/0 is the connection to the cable modem, this is the outside interface, set at auto at both ends.
Im getting on the vlans eg. 51253 packets dropped however network traffic isnt impacted and everything runs fine, as well as 46532 switch ingress policy drops.
Example;
ciscoasa# sh int vlan1Interface Vlan1 "inside", is up, line protocol is up Hardware is EtherSVI, BW 100 Mbps, DLY 100 usec MAC address 70ca.9b36.ab80, MTU 1500 IP address 10.x.x.x, subnet mask 255.255.255.0 Traffic Statistics for "inside": 43250588
We have a setup with a MS-TMG - ASA (8.2.4(4) in routing mode) - (internal) Router - FWSM - Router - Exchange with NLB. We have now the problem that IMAPS is not really working through this setup. It works from internal (without ASA and TMG inbetween), but not reliably through the internet. There is a rule on the ASA which permits the ports from the TMG to the Exchange NLB address.We opened a case with Microsoft and they told us that not all tcp-syn packets are received by the Exchange server which were sent by the TMG.Thus I sniffed on the ASA with a packet capture and indeed, a lot of syn packets were on the interface to the TMG, but not anymore on the interface to the internal router.This ASA also filters all other internet<->company traffic, so there's a lot of stuff running.
Maybe it's dropped in the ASP, or is the capture maybe not valid?Here the show asp drop:
ASA01-Internet# sh asp drop Frame drop: Invalid TCP Length (invalid-tcp-hdr-length) 1 Reverse-path verify failed (rpf-violated) 319 Flow is denied by configured rule (acl-drop) 477077 First TCP packet not SYN (tcp-not-syn) 10212 TCP data send after FIN (tcp-data-past-fin) 41 TCP failed 3 way handshake (tcp-3whs-failed) 824 TCP RST/FIN out of order (tcp-rstfin-ooo) 1419 TCP SEQ in SYN/SYNACK invalid (tcp-seq-syn-diff) 6 TCP SYNACK on established conn (tcp-synack-ooo) 1 TCP packet SEQ past window (tcp-seq-past-win) 821 TCP invalid ACK
I have an ASA5510 with CSC Module which is inspecting HTTP traffic. We need to be able to use http radio stations. Some radio stations work but some don't work. I excluded my computer ip address from the CSC filtering but i am still unable use certain radio stations. I thought since my computer is excluded from the CSC filtering and some radio stations don't work that it must be the firewall that is blocking the traffic. I removed the rtsp inspection and it won't work.
I need to redirect all http and https traffic from one source in a dmz network, to port tcp/8080 on a proxy server on the inside network.
The source device doesn't handle proxying very well, so i've been advised to redirect the tcp/80 and tcp/443 ports to tcp/8080 as it passes through the firewall.
I have a strange problem in my ASA 5510 firewall. I turned on HTTP inspect policy to block certain URLs, but that destroyed svn communication. Interestingly, if I use simple web-browser to access svn server - it works, but any svn-client requests fail with an error "Could not read status line: An existing connection was forcibly closed by the remote host". I did some packet sniffing, and discovered that with HTTP inspect off the Webbed request is answered, but with HTTP inspect on it is rejected with an error unauthorized. Here are examples of success and failed conversation packets:
I found one mentioning of that error with that assessment: "Older firewall/proxies do not understand the Webbed related HTTP requests for accessing Subversion using HTTP{ URL} in that post But not any useful tips.
I am using ASA 5510 and I have a specific problem with Http Connection to receive a video Flow ( RSTP protocol ) in the LAN. Some Pc users (192.168.1.133,in the log) with ASA Lan Interface as gateway can ping the Camera but don't receveive the video flow.Some Pc users (192.168.1.116,in the log) using another gateway can ping and receive the video flow. I used Whireshark to capture traffic between camera and Pc using the 2 gateway. I joined Logs with this message.It seems to be a problem of TCP segments on the ASA, I try to changed some TCP options but it's still the same:- Disable Force Maximum Segment Size- Enable Force TCP Connection to Linger in TIME_WAIT State for at Least 15 Second.
I have a PIX 515E V7.0.4 and I'm having trouble with http access between the inside interface and a DMZ zone I have. I have a web server setup in the DMZ with an web interface to upload/download files. I can connect to this interface from a workstation in the inside network but when I try to download a file it is incredibly slow. If I upload a file there are no speed issues. If I connect using an https connection then both upload and downloads are at speeds I would expect.
I have disabled http inspect but this didn't improve the speed connection.
Other http communications from inside to outside do not have any speed issues in either direction.
I am trying to configure my ASA 5545 firewall in area 0 but when I do so, the neighbor relationship never establishes. A debug on OSPF gives only one response: [code] Why the ASA is ignoring the input packets?
I have a Cisco 871 router that used to have Access list based security. now I am trying the ZBFW for the first time. I thought I had a pretty good program until I found all my traffic was getting dropped. This is my first stab at ZBFWs and I am a bit confused esp with the default class part.
The router is for my house and thus also has to have priority for gaming. I will add the gaming and voice QOS once I get it working,
Guest VLAN has access to 2 IP's in Data for printing. Cisco871#sh run
Building configuration...
Current configuration : 8005 bytes ! version 12.4 no service pad
I happen to noticed the FWSM was dropping packets at about 387 packets every 5 minutes. My outside FWSM is WAN facing and has a 1gig link (35% utilized) my inside facing has about 100 downstream switches to the closets. I do not see my 6509's back plane is being over utilized and my understanding of the FWSM show be go for 5 gig so it isn't oversubscribe. Why i am seeing packets dropped?
I have one server-A(windows 2008) installed one application called"host front" which gives athentication to connect Linux(mainframe console) server (SERVER B).These 2 servers are bihind the firewall.If one internal user who has the athentication to logine server-B ,tried to login server A,will get the" username and password"screen and once they enter the username and password ,will get the server-B screen.But if somebody try to connet via MPLS(we need to test MPLS site customers) from outside via ASA 5540 ,to server-A will get the "username password" screen and once enter the credentials, after 1 minitue will get error"http server faild to send datas to the server" and will not move to server -B screen.
Right now, in my network there is no proxy server and all users go straight through the ASA to access internet. I would like to put a squid with dansguardian (for web filtering). Steps in getting all http and https traffic from ASA go via my squid?
I'm looking fot a way to do static URL blocking with ASA and when the URL is blocked present a "Web Page" to the user saying that it's been blocked.
So, i was wondering if i can use the http parameter "spoof server string" to replace the original URL sent by the user for another URL that points to an internal web server holding a basic page saying "Your URL request has been blocked".
The point is to have a way to tell users that the page they are trying to browse is blocked by a policy.
I am using ASA5510 and i want to know if it is possible to redirect http traffic to an internal proxy software. I explain : PC from the LAN use a internal proxy in their IE browser but some other PC doesn't use it.They are directy connected to the Internet using the Public IP from the WAN interface ( via NAT). Can we redirected this HTTP Traffic from the WAN interface to the Proxy in the LAN ?
Http Traffic will be routed like that : PC -> WAN interface -> Proxy -> WAN interface -> Internet In fact,can we create a rule saying : All http traffic which doesn"t come from the IP Proxy must be redirected toward proxy.
