Protocols / Routing :: BT Homehub 2.0 - Open Same Port On 2 Devices?

Sep 4, 2011

Unfortunately we are stuck with a bt homehub 2.0. We all hate this thing with a passion. We cant workout how to open the same port on 2 devices. When we try it says theres a conflict and just refuses to let us do it. So only one of us can play the game we want, without it timing out. Now I've tried the BT forums, there was no support there. I phoned up BT and to my absolute disgust, nobody there knew how to use the homehub, or simply said 'turn off the firewall'.

View 2 Replies


ADVERTISEMENT

Protocols / Routing :: Can't Open Port 15961

Jul 19, 2012

im trying to set up my cctv so i can watch it from my iphone outside my network and it says to open ports 80, 9000 and 15961. ive successfully opened ports 80 and 9000 but cant seem to get 15961 to open. i have an att 2wire.

View 17 Replies View Related

Protocols / Routing :: Want To Open Port Forward To Utorrent In A Router?

Sep 19, 2011

i want to open portforward to utorrent in arouter but i cant open the addres of the router lookand when i go to local area connection status /status/detailsi found number of ip but there is no gateway i take whole ip and put them in browser and its dont open but the last friday i wake up in 3am run cmd and put ipconfigi found the gateway 192.168.2.45put it it in browser its open want username and pass i know them but i see lets doit next day going to bed next day the gate way reverse to the stupid gateway in in the pic i cant use aprogram to open port as i cant knowing my router mode

View 1 Replies View Related

Wireless Devices Work On BT HomeHub But Not Samsung N150?

Feb 6, 2013

My wife has a Samsung N150 that connects wirelessly everywhere except at home.All other wireless devices work on the BT HomeHub but not the N150.We have just been on holiday and the N150 connected to everything we came across, without a hitch.

View 1 Replies View Related

Cisco 2000 :: Router+48 Port Switch Instead Of Homehub

Apr 30, 2012

I am trying to remove my BT Homehub2 and replace it with a router connected to the ADSL line using RJ11 to RJ45 cable in f0/0 configured ip address 86.177.164.200.F0/1 is configured to 192.168.1.254 (current BT Homehub IP) this is connected to my 48port cisco switch in port GI1/0/48.VLAN1 set to DHCP and my host is connected to GI1/0/2 and also configured to DHCP.Ignoring the WAP for now, what am I doing wrong? I know it will be a small IP issue somewhere, do I need to configure GI1/0/48 and GI1/0/2 with IP address'? Am I using the wrong ISP address on my routers F0/0 port?

View 2 Replies View Related

Protocols / Routing :: Open Nat Xbox Live / Netgear 3400 With Windstream Dsl?

Jul 2, 2011

I have tried opening the ports on xboxs website. tried dmz. tried both. i have a basic understanding of changing your xboxs ip.i have disabled windows firewalls and got rid of macafee altogether.

View 10 Replies View Related

Protocols / Routing :: Port Forwarding Through 2 Routers?

Jun 16, 2012

I am trying to port forward for Vuze and I am having a problem understanding the concepts at [URL] for working within two routers. I have a Zoom 5241 cable modem connected through a Motorola VT2442-VD for Vonage VOIP, then connected through my Netgear RangeMax WPN824v3 wireless router, to my computer. I am also running AVG internet security. Here is a look at my ipconfig /all:

C:Users
ex>ipconfig /all
Windows IP Configuration
Host Name . . . . . . . . . . . . : MarekFamily
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No

[code]....

However, I do not understand where to setup the static ips and where to drop DHCP to be able to port forward successfully. I have tried in Vuze to set up acceptable ports 51600 for TCP and UDP, but they continue to get this error: "NAT Error - Connect attempt to 67.60.124.173:51600 (your computer) timed out after 20 seconds. This means your port is probably closed." I do know that the Ip present is from my Vonage with my external IP address. I even tried to establish rules for TCP and UDP within AVG Firewall settings for the Vuze program.

View 6 Replies View Related

Protocols / Routing :: Port Forwarding On BTHome Hub

Apr 5, 2011

I've been having trouble signing into the PSN and Sony have given me some TCP and UDP ports to enter, I presume they're the ports for PSN.
TCP Ports: 80, 443, 5223, and 10070 - 10080
UDP Ports: 3478, 3479, 3658, and 10070,
When you want to open new ports on the BT HomeHub you have to fill out this form, and I don't know whereabouts I enter these ports I've been given.

View 1 Replies View Related

Protocols / Routing :: Unable To Forward Port

Feb 2, 2013

So I need to forward certain ports to play/log-in game:

TCP: 80, 443, 2099, 5222, 5223, 8393-8400

UDP: 5000:5500

I did forward them in my router and checked them with PFPortChecker, every port seems to open except 2099, I don't understand why.Note that I disabled Windows Firewall, Router's Firewall, and I'm using Kaspersky Internet Security which I disable while checking ports/logging to game

View 19 Replies View Related

Protocols / Routing :: Forcing Use Of Specific Outbound Port?

Jan 24, 2013

force something such as a Telnet client to use a particular outbound port when opening the TCP connection?

View 3 Replies View Related

Protocols / Routing :: AUI Ethernet Port On Cisco 2501?

Apr 17, 2012

I am trying to setup my lab so I purchased 3 cisco 2501 to study for my CCNA, my question is? I have 2 serial interfaces and 1 AUI for ethernet on each router. How can I configure the Ethernet interface, if I don't see it on the configuration. From the CLI command I issue the command show ip int brief. But It only shows the 2 serials but no E0 interface.

PS. I do have an Ethernet Transceiver connected to the AUI port on the router with a straight through cable going into a 2950 switch.

View 6 Replies View Related

Protocols / Routing :: Modem And Router Port Forward?

Aug 15, 2011

I'm trying to forward ports for game connections. For this particular game, I'm trying to forward port 7777My ports aren't forwarding according to: Open Port Check Tool - Test Port Forwarding on Your Router and Open Port Check Tool[CODE]

View 13 Replies View Related

Protocols / Routing :: Opening Port 80 For WAN Access To Localhost?

Dec 22, 2012

So I am working on a website with MySQL/PHP that I have been developing on my Linux box. I wanted to show a friend my progress so I temporarily opened up port 80. So he was able to just type in my public IP and it brought him to my localhost index.

My question is, when I type in my IP address in the URL bar, does the web browser automatically just assume port 80? What happens if I want to have 2 different servers from the same local network and one is running through port 80 and the other is running through port 90? In this case, would I have to type ":90" to access the machine running on port 90?

View 1 Replies View Related

Protocols / Routing :: Port Forwarding On Actiontec Q1000?

Jul 15, 2012

I have my internet through CenturyLink which is a DSL connection running on an Actiontec Q1000 on a Windows 7 set up. I'm trying to run a subsonic server on my computer to stream my music collection. It was all working beautifully until I had to switch to this modem from my previous. Now, when I go to canyouseeme.org, it can't see that 4040 and 8080 are open. They need to be for subsonic to work? I've tried to set it up as portforwarding

View 5 Replies View Related

Protocols / Routing :: SIP Trunk Port Range (VOIP)

Aug 14, 2012

I've recently set up a PC-based IP PBX in our small business which uses a SIP Trunk for up to 3 simultaneous voice calls. Ports needed to operate include 5060 (SIP-UDP) and then a huge range of high-number UDP ports which I believe is for the 'media' or audio. Let's call the range UDP 49,152 to 64,512. I only know a little about the SIP protocol but my understanding is that each call will randomly use a few ports from this range across which will pass audio, Is there a need to have such a wide range of ports open? If my SIP trunk is only capable of 3 simultaneous calls then it seems only 9 or so of those open ports could get used at once. Could I not just open, say a range of 100 ports and be fine, thereby reducing the security risk?

View 4 Replies View Related

Protocols / Routing :: Using Port 1 - 80 For All Outgoing Traffic Possible With Application?

Oct 9, 2012

I want to be able to use port 1-80 for all outgoing traffic. I have a VPS outside my home, which can redirect the packets to the prober ports.Is it possible with an application on the computer and VPS? Or is it impossible?

View 1 Replies View Related

Protocols / Routing :: Port Forwarding 25565 Fails?

May 13, 2012

At first I tried to port forward 25565 on my D-Link Router account, but that didn't work for anyone trying to connect through the External IP.

People can connect locally over my network and I can connect to the game via localhost, but like I said, no friends from abroad.

I've checked my External IP and that doesn't work, I've tried resetting my router to factory default and then reinstalling the firmware for the model, that didn't work. I tried removing the firewall altogether, and also just allowing 25565, but that didn't work. I also got my friend to take their firewall off as well.

(Also, it should be known, when I'm port forwarding I'm allowing access, and have 25565 set in both TCP and UDP. I tested to see if the port was open on Open Port Check Tool, but it said it was closed (connection timed out) even though I had it forwarded)

View 4 Replies View Related

Protocols / Routing :: Port Forwarding TP-Link TD-W8970?

Jan 19, 2013

Router Model: TP-Link TD-W8970 port forwarding my modem/router. I previously was able to successfully port forward a Valve Source Server and had other people join on the internet so...(It worked) I recently reformatted and since have had issues.

I'm currently setup with PPPOA and I've added various ports for different programs (a Teamspeak 3 Server[9987] and Minecraft[25565]) either dont work. I used a port checker program and they either say the port is closed or the connection is refused...I've tried using a static IP but I think i configured it wrong becuase i was barely able to get the internet while using it, either way..the ports didn't open.

DCHP is disabled (Tried enabling, didn't work) The above ports are enabled with Windows firewall (inbound+outbound) and Im not using any Anti-virus software to block the ports. Windows 7 64bit, fresh format and ports that wont go through.

View 4 Replies View Related

Protocols / Routing :: Port Forwarding To Access Share Point

Mar 31, 2013

I've been trying to configure my router which is linksys E1000 to forward port to my sharepoint server. Here is what I have done so far, setup single portforward to i.e 192.168.xx.xx using port 4848.Now my question is, do I need to configure sharepoint to receive this incoming connection. I do need to have my sharepoint be accessed anywhere on the web.

View 1 Replies View Related

Protocols / Routing :: Opening Port 443 On Rangemax Wireless Router?

Aug 23, 2012

I need to open the 443 port on my rangemax wireless router to enable credit card processing

View 1 Replies View Related

Protocols / Routing :: Port-forwarding - Linking Back To Network URL?

Jun 30, 2012

I have set up port forwarding for my WD Network HDD, which runs a Media Server (Twonky). Now, I have tested the ports and accessed it through the internet and it works fine, until... I click a link to open a folder and suddenly I get a "No such page" error thing. I have however identified this problem, it seems that when I go off the main page it re-routes to the original network address, not my IP forward address. For Example if my IP was 82.9.12.456 and the port was 800 i would go to "82.9.12.456:800" and it would load but once I navigate i go to "192.168.0.*:800/*****" and does not load the page. If i then copy and past my IP into the URL it works, but this is annoying.

View 3 Replies View Related

Protocols / Routing :: Port Forwarding Ranges On Cisco Rv180w Router?

Aug 13, 2012

I'm just setting up a Cisco rv180w router to replace our aging Belkin. I need to allow a range of ports through the firewall to a particular PC on our internal network that runs our VOIP/SIP Trunk phone system.

The Cisco's Port Forwarding looks like it can only forward one port at a time, but for our phones I need to allow a full range of ports (in this case ports 49152-64512) to one machine at 192.168.x.xx.

On the Belkin I used something called 'Virtual Servers' which allows you to enter ranges of ports. Anybody know what the equivalent might be for the Cisco router?

View 13 Replies View Related

Protocols / Routing :: Comtrend WAP5813n Router Fails At Port Forwarding

May 5, 2011

My Comtrend WAP5813n router, seems to be failing at port forwarding as I have configured it to forward ports,all the port checkers (offline and online) say those ports are open, yet I cannot access through them,it just fails to forward them(My server isn't blocking anything because it has worked on a previous router).

View 19 Replies View Related

Protocols / Routing :: Port Forwarding Minecraft - Qwest Modem / Linksys Router?

Oct 1, 2012

port forwarding this im trying to setup a minecraft server with bukkit and i tried a number of things to port forward and it won't open port. I have a tomato firmware linksys router and a qwest modem.

View 1 Replies View Related

Cisco Switching/Routing :: 3750X Port Channel Load Balancing Protocols

Jan 15, 2012

What I am attempting to achieve is to aggregate trunk ports out of a VMware server into a single logical connection to give as much bandwidth as possible, the switches are 3750X and are three stacked together with the server connections spread across the stack. What I am not sure about is if two port channel load balance protocols can happy co-exist on the switch, by default the switch is using MAC address load balancing and Vmware wants to use IP Source load balancing. As other trunks and channels exist on the switch I don't want to make a change that will affect the other live connections if changing this is a global setting and not local on the channel.

View 2 Replies View Related

Difference Between Open And Vendor Specific Protocols?

Nov 28, 2012

What is the difference between open protocols and vendor specific protocols?

View 1 Replies View Related

Cisco Switching/Routing :: ASA 5505 Port Is Coded Open / But Says Closed

Feb 19, 2013

I have a Cisco ASA 5505 with a fairly simple set up. Few VPN tunnels and only 3 open ports for applications. I have entered the following lines static (inside,outside) tcp interface 9002 10.0.3.230 9002 netmask 255.255.255.255 access-list outside_access_in extended permit tcp any interface outside eq 9002.I have done this before with zero issues. The other two ports are open, however, port 9002 will not be visable from the outside. The ASA says it is open, but if I go to a site like canyouseeme, it shows closed. I cannot connect to the application either.

View 3 Replies View Related

Cisco Switching/Routing :: Configure Pop3 Port To Be Open On ASA 5505?

Apr 29, 2013

I need to configure pop3 port to be open on my ASA 5505. I've created an acl and static route to do this but for some reason, it's not open.

View 1 Replies View Related

Cisco Switching/Routing :: SGE 2000 - Can't Open TFTP Client / No Free UDP Port

Oct 19, 2010

I have several SGE2000 in production and every night I save the current configuration to a tftf server... from time to time I get the following error: [code] Can't open TFTP client.At this time, the only way to be able to save the config again is rebooting the switch, but this is not a solution I am comfort.

View 5 Replies View Related

Cisco Switching/Routing :: 3560 Command Shows Two Devices Connected Through Same Local Port?

Oct 14, 2012

show cdp neighbors command shows two devices connected through the same local port?I have a Cisco 3560 that when I issue the "show cdp neighbors" command I get the following results: [code]
 
the question is why is this showing that Gig0/3 is being used twice to  connect to two different devices.  I have verified there is no hub  connected to this port and in fact Switch3 is not connected to Switch1  at all yet it still shows up in the CDP table.
 
I have cleared the CDP table on every device at this location and still get the same results. 

View 4 Replies View Related

Open - Download Speed On Some Devices Very Slow

Apr 3, 2012

has full Download/Upload speed while I only have a max. of 5kb/s download speed. The ping is perfect (20ms) and the upload rate is around 150 kb/s. I tried it out with my laptop on Windows 7 and Ubuntu and also with my Android Smartphone. I don't know why it's not working.

View 7 Replies View Related

Cisco Switching/Routing :: SG300-10 See All Traffic From All Connected Devices On Any Port / Where To Connect Listening Device

Dec 20, 2012

In my LAN environment, I'm using two cisco SG300-10 switches. Both switches are connected by GE10 on both switches, where both ports are set to trunk.Now on all ports 1-9 on both switches, I'm having client computers attached. So I set ports 1-9 to "access" mode.All interfaces on any switch is left in default vlan.
 
Is it normal that I see all traffic from all connected devices on any port where I connect a listening device?What I'd like to achieve is, that only traffic that is meant for a specific workstation is actually forwarded to this workstation. By now it seems that I get all the traffic from everybody.

View 6 Replies View Related

Cisco Wireless :: 1140 - Apple Devices Asking For Password On Open Networks

Jan 27, 2013

we are running 1140's and 1130's in autonymous mode and seeing a TON of requests for passwords on IOS devices where we have an open network.
 
This typically happens when we things are busy in the space.
 
All other non IOS devices do connect, and most IOS devices connect after a considerable amount of time.

View 5 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved