Cisco 2000 :: Router+48 Port Switch Instead Of Homehub
Apr 30, 2012
I am trying to remove my BT Homehub2 and replace it with a router connected to the ADSL line using RJ11 to RJ45 cable in f0/0 configured ip address 86.177.164.200.F0/1 is configured to 192.168.1.254 (current BT Homehub IP) this is connected to my 48port cisco switch in port GI1/0/48.VLAN1 set to DHCP and my host is connected to GI1/0/2 and also configured to DHCP.Ignoring the WAP for now, what am I doing wrong? I know it will be a small IP issue somewhere, do I need to configure GI1/0/48 and GI1/0/2 with IP address'? Am I using the wrong ISP address on my routers F0/0 port?
View 2 Replies
ADVERTISEMENT
Sep 16, 2012
I have a sge 2000 24 port POE switch that won't boot, won't communicate on console or TCP/IP, and all of the port lights are lit up green. Holding down the reset button doesn't fix the issue and there aren't any lights illuminated on the left hand side of the switch.
View 1 Replies
View Related
Sep 4, 2011
Unfortunately we are stuck with a bt homehub 2.0. We all hate this thing with a passion. We cant workout how to open the same port on 2 devices. When we try it says theres a conflict and just refuses to let us do it. So only one of us can play the game we want, without it timing out. Now I've tried the BT forums, there was no support there. I phoned up BT and to my absolute disgust, nobody there knew how to use the homehub, or simply said 'turn off the firewall'.
View 2 Replies
View Related
Nov 27, 2012
what are all the CLI commands supported by Cisco SFE 2000 switch?
View 2 Replies
View Related
Jan 7, 2013
I have a big doubt. Can I connect a LAN switch (i.e. 2960, 3560 or 3750) to a couple of Nexus 2000 FEX (i.e 2232P or 2248TP) and have a Port-Channel or vPC with STP active and several VLANs through this Port-Channel? Or Can I only connect servers to these N2K FEX?
View 3 Replies
View Related
Jan 6, 2013
Lately I've noticed some strange behavior on some of the switch ports. When I go through the logs my SGE2000/2010 stack, I see that some of the ports randomly lose their connection:
2147482703 05-Jan-2013 04:11:43 Warning %LINK-W-Down: 2/g14 2147482704 05-Jan-2013 03:35:20 Warning %STP-W-PORTSTATUS: 2/g33: STP status Forwarding 2147482705 05-Jan-2013 03:34:50 Informational %LINK-I-Up: 2/g33 2147482706 05-Jan-2013 03:34:47 Warning %LINK-W-Down: 2/g33 2147482707 05-Jan-2013 03:34:19 Informational %LINK-I-Up: 2/g33 2147482708 05-Jan-2013 03:34:17 Warning %LINK-W-Down: 2/g33 2147482709 05-Jan-2013 03:34:15 Informational %LINK-I-Up: 2/g33 2147482710 05-Jan-2013 03:34:14 Warning
[code]....
I'm having trouble locating the source of the problem. The devices connected to the port are servers and desktops. This happens frequently throughout the day, but not always on the same ports. What could cause the random drops?
View 8 Replies
View Related
Apr 23, 2013
nyone know if "vpc-orphan-port suspend" works if i put on N2k interface. not the fex link. example i have fex 101 and i put on eth 101/1/10 will it suspend the port on N2K connected to secondary N5K when peer link is down?
View 2 Replies
View Related
Oct 19, 2010
I have several SGE2000 in production and every night I save the current configuration to a tftf server... from time to time I get the following error: [code] Can't open TFTP client.At this time, the only way to be able to save the config again is rebooting the switch, but this is not a solution I am comfort.
View 5 Replies
View Related
Jun 13, 2011
Does the LACP will be supported on Nexus 2000 host interfaces when parent switch is Nexus 7000?
View 5 Replies
View Related
May 8, 2012
On the supervisor card of a cisco 6500 series, according to the following link, [URL] it only has 2 uplink ports on the card. Would I be correct in assuming that I only have those to ports that I can configure IP addresses on?
The cisco that is being devlivere is coming with a 48 port switch and 24 port fibre switch. Could I change any of those ports into a router port and configure IP addresses on those?
The supervisor card is a ws-sup-720-3b the 48 port switch is a ws-x6748-ge-tx the 24 port fibre switch is ws-x6724-sfp
View 3 Replies
View Related
Jun 5, 2013
I'm fairly new to Cisco products am in the process of developing my network knowledge on a deeper level. I have a 3825 with a HWIC-4ESW and I'm struggling to fully understand how the two "see" each other. I've setup a V LAN with a layer 3 address on the HWIC and added the switch ports to it. This seemed to allow devices connected to the switch ports to talk to the built-in router ports. I thought this was all making sense until i applied an access-list to the router port. It's a simple ACL i'm just using for testing and the only thing it does is blocks telnet from anywhere. I know the ACL is setup properly because if I connect a device directly to the router port i cannot telnet to the port. However, if i connect a device to one of the switch ports, i am able to telnet to the router port successfully.
It seems that I'm missing something with how traffic flows from the switch port to the router ports and how the two "see" each other.
View 2 Replies
View Related
Feb 26, 2012
I was looking for a way to connect an AUX port from a 1700 router to a 6500 switch module console port, to see the output of the Switch's on the 1700 router, in case there is a network downtime, I could see what's going on in the switch, what cable should I use ? Also, is there is any kind of documentation for this type of config what have I seen is very few info.
View 2 Replies
View Related
Feb 1, 2011
I have just given my Mum an old Dell desktop computer of mine. She has BT Broadband with a Homehub. I have connected everything up and installed the Homehub software on the computer but when it tries to search for the network connection via the BT software, it keeps saying the network card can not be detected. The network cable is plugged in and working. All the drivers are up to date.
View 14 Replies
View Related
Oct 12, 2012
for some reason my laptop disconnects randomly and i cannot connect again until i go and reset the router. if i try to reconnect without reseting the router i get the message 'cannot connect to BT homehub xxx' it happens at least 4 or 5 times a day, it happened at my previous address too (completely different router & isp) im not quite sure what other info i can give relating to the matter.
View 7 Replies
View Related
Feb 6, 2013
My wife has a Samsung N150 that connects wirelessly everywhere except at home.All other wireless devices work on the BT HomeHub but not the N150.We have just been on holiday and the N150 connected to everything we came across, without a hitch.
View 1 Replies
View Related
Apr 23, 2012
Can switch do a port forward without a router just plane switch to port forward to another network crossing the internet.
View 1 Replies
View Related
Apr 16, 2012
For only $7.91 each when QTY 50+ purchased - 8 Port 10/100 Mbps Fast Ethernet Switch | Network Switches/This is my modem/ router given by Verizon FIOS: Westell A90-9100EM15-10..All of the cables I am using have been tested and work. All of my devices (PC, Laptop, PS3, Xbox 360) work when plugged directly into the router. Wireless works fine, but I want as many devices as I can to be wired and using the other ports on the router are not an option.I plug the cable from the router to the switch's Port 1 and then plug devices in and none of them work. The switch does not have a designated "In" port. Just Port 1-8. The reviews on Monoproce say that others were able to do exactly as I am doing with no setup required.I have tried plugging them in one by one and none work. The laptop and PC cannot connect to the router via 192.168.1.1 as they normally do. Also it registers as "Unidentified Network." [code]
View 14 Replies
View Related
Jan 15, 2011
If I can use my switch as a router or a way to get more Ethernet port? Since my router is down for the count and I need more ports!
View 4 Replies
View Related
Feb 24, 2011
Currently I have a 4510-48g HP3COM switch as a core switch for my 4 VLAN network (which I hope to send back cause it doesn't do what I wanted it to do... PBR, which is what I need to route specific VLAN's to specific interfaces on the sonicwall,.. cause sonicwall dont understand trunk or spanning tree,. meh!) This may not happen so I've dug out an old CISCO 1800 sdsl router that has 1 FE0 port and 8 other ports, FE 1-8.
The first thing I need to do is get everything to talk to each other. So I plugged the switch into it via its configured trunk port, and configured 4 sub interfaces on the router 1800 and all seemed happy as larry and working. The problem I have is I dont seem to be able to create sub interfaces on the other ports!?
[Code]...
View 6 Replies
View Related
Oct 4, 2012
I have ATT u-verse currently and it connected to a router but I am going to need several more gigabit ports so I wanted to get an 8 port gigabit switch. I would plan on running a cable from my U-Verse modem to my router then to my switch giving me wireless and 8 gigabit ports. Would that work? I've never done this before so I wasn't sure if I was missing something or not.
View 2 Replies
View Related
Jul 6, 2011
So I am contemplating the setup for the network in my new home, how to connect 24+ ethernet ports in the house to a single network. I was thinking of getting a nice dual-band wireless router, but those usually only come with 4 or so lan ports. How would I then utilize a large 24- or 48-port switch to connect everything to the router?
View 2 Replies
View Related
Dec 28, 2008
what is the use of no switch port command in L3 switch?
View 7 Replies
View Related
Mar 19, 2011
ISP Cable in Smart box. 4 cat 5 cables from various rooms in house to feed cable ready TV's and one from my computer room. Can I connect all cat 5's to switch that is connected to cable modem located in Smart box and connect Wireless Router to cat 5 in the computer room and expect router to work properly?
View 4 Replies
View Related
Jan 16, 2011
is it possible to assign a loopback address to a typical switch port on a 2950 switch? I want to be able to have some devices connected to a switch to test access lists and VLANs.
View 3 Replies
View Related
Dec 20, 2011
I have a Cisco 1941 K9 Router. I want to add POE functionaltiy to it. Specifically I want a 4 port EHWIC POE switch to power a couple of AP's.
This is what I understand I need; Upgrade/replace the internal power supply with PWR-1941-POE power supply, This is supplied with a fan replacement also (not yet purchased).buy 1 x EHWIC-4ESG (4 port switch)buy 1 x ILPM-4 (inline daughter card / power supply board) I think the real question here is the 4 port switch... there are two types available one is EHWIC-4ESG=the other is EHWIC-4ESG-P=
Is there any difference between these two switch modules? or are they the same and the more expensive "P" version is simply supplied with the ILPM-4 daughter card for POE?
I have recieved via courier today 1 x EHWIC-4ESG, and found a ILPM-4 on ebay for a good price. WIll this provide POE through the switch EHWIC-4ESG?
View 7 Replies
View Related
Jul 27, 2012
I want to expand my network with this switch. I have a cable from a DSL router directly connected with a network device. Now I want to connect first from my DSL router with the switch and then from the switch to the network device. But which port of the switch to connect with the router?
View 2 Replies
View Related
May 23, 2013
My questions is can a 4 port PoE switch module (EHWIC-4ESG-P) and a 8 port switch module (EHWIC-D-8ESG) be used at the same time in a Cisco 1941 router?
View 1 Replies
View Related
Sep 17, 2011
I am wondering if xconnect L2TPV3 feature could be done on multiple SVI interfaces on 871 router and 2911 router with built in 8 port switch?Like I need to extend two ethernet interfaces and can I use two SVIs on router built-in switch module on each side?
View 2 Replies
View Related
Jun 8, 2012
I literally just got my hp 2000-410US notebook pc laptop and I just connected it to my Belkin router. For some reason, my new laptop would not connect to the internet even though I am connected to the router. I have another laptop which is a hp G42-410us notebook pc but it connects perfectly. I already set up my settings for the new laptop but I am not sure if I missed something during the setup that allows me to use the internet.
View 5 Replies
View Related
Jan 13, 2011
I recently got a second hand Advent Roma 2000, which runs with Windows 7. After a while I managed to configure it to allow my T-Mobile internet dongle to connect. However, we recently got BT put in and I cannot find the wireless router [BT HomeHub 2.0].Now, at first I thought maybe the wireless detection on the router was faulty, but I checked my 360's wireless connection and that has connected with no problems.
View 13 Replies
View Related
Sep 2, 2011
I need a small number of computers connected to the Internet through the E4200.E4200 must be connected to the switch via the LAN port.The basic network is a network of class A - 10.xxx/255.0.0.0.How do I do?E4200 can not enter a mask of 255.0.0.0.
View 1 Replies
View Related
Feb 29, 2012
I have a 1941 that I am going to deploy with a HWIC-D-9ESW switch module (I only need 3 switch ports but need the PoE). I am going to hang a 1262 autonomous AP off one of the ports but I need to configure MAC address port-security so that only that AP can pass traffic. I know the switch modules are 'almost' exactly like a switch for commands but I can't seem to enable or configure any port-security settings. Is port-security no available on the switch modules?
View 3 Replies
View Related
Dec 18, 2012
I have a 2821 router and need to add another Ethernet port.
However, all the Ethernet modules seem to be End of Sale and the suggested replacements are only compatible with the ISRg2 range.
View 2 Replies
View Related
