I recently got a second hand Advent Roma 2000, which runs with Windows 7. After a while I managed to configure it to allow my T-Mobile internet dongle to connect. However, we recently got BT put in and I cannot find the wireless router [BT HomeHub 2.0].Now, at first I thought maybe the wireless detection on the router was faulty, but I checked my 360's wireless connection and that has connected with no problems.
View 13 RepliesI have an Advent 5421 with Vista installed, it's nearly 3 years old and I have a few problems with it, but nothing too terrible, until yesterdy when I switched it on and found the wireless connection has mysteriously disappeared. When I try to connect it says there are no networks to connect to, which is obviously bollocks. The internet will now only work if I plug the cable in, which is no good as I share a flat with 2 other girls and if I do that, they lose their connection. I don't understand whats happened. I really am not computer literate at all, the only thing I tried was to make sure I had the latest software updates for my computer, which I did, but nothing happened.
View 1 Replies View Relatedi have downloaded vista to my Advent 4213 and now i can't get wireless connection to the internet?
View 2 Replies View RelatedMy advent 4211 has intermittent wireless connectivity.I have tried resetting the channel on the hub, but have had no luck thus far. Also I have updated the driver from Realtek, but the problem persits. I have also moved the hub to another location.The thing is that I have another Laptop which has no problem connecting.
View 1 Replies View RelatedI would like to know how to set up a wireless connection intel advent7106
View 1 Replies View RelatedI purchased an Advent DT2410 about a month ago from PC world. It came with Windows 8 OS a USB wireless stick and the following basic spec:
Intel® Core™ i5-3330 processor
Genuine Windows® 8
Memory: 8 GB
Hard drive: 2 TB
So initially brought it home, set it up and fired up connected to the internet perfectly fine with the stick. Then about once every 2/3 days, it would pick up no internet connection despite being next to the router and after 2-3 shut downs in a row would work again. When the connectivity icon was blank, I would go to trouble shoot it and windows 8 wouldn't do anything, not even attempt to detect the problems (bare in mind this PC is brand new).So I leave my home by my University and came back to my parents for Christmas. Lugged my PC back with me and set it up.So first I connected to the wireless no problems, loaded up my favorite forums and after image hovering over about 3 images the 4th would only load the top 3rd of the picture. Open up new tabs "Connecting" until:
A) Server would time out
B) Wireless would DC and then reconnect (before basically repeating the "3 image view")
C) Would work for a few hours (e.g. a streamed film) before screwing up again (rare)
So, reinstalled drivers, replaced the USB wireless stick (802.11n.) AND STILL problems problems problems. I then cleared the IP/TC stacks (I believe they're called) did it through the elevated command prompt and still nothing. So i'm using my sister's laptop to write this as my internet on my PC barely runs long enough for me to be able to check this page or download the program mentioned in the sticky.
I have just purchased a new EA3500 router and have fairly painlessly managed to get my desktop (running Windows XP), my lap top (running Windows 7), ipads 1 and 2 and blackberry all to connect to the wireless hub. I even have it talking to a WD 1T external hard drive.
BUT try as I might I can't get an old sony vaio running windows 2000 professional to connect to the internet. It talkes to the box and even allows the lap top to hop on as a guest but it goes through to a guest sign on web page and no matter what combination of passwords (i am sure i have the write guest sign on) it just refuses to actually connect. I never had a problem connection to our previous wireles router.
how to change the time zone, the current time always show Firmware Version:1.01.6Current Time:Sat, 1-Jan-2000 00:08:40 and can't connect PPPOE
View 1 Replies View RelatedThe router works fine until I plug the 4th wire in the back, which goes to a 2nd desktop computer, then it is only a matter of time until the router drops all internet connections including the direct wire to desktop #1, wireless, and the other two wires.This is my 2nd e2000 router since Amazon replaced the first one after about 4 months as it was having the same problem.
View 5 Replies View RelatedHow do I update the firmware on my N wireless router with version 2000? It says there is an update, but I can't update it with the one firmware update that's available for download.
View 4 Replies View RelatedI have Lynksys router WRT54G. I have 3 laptops in house connecting to internet with no problem. A new person has moved in with a laptop that has windows 2000. The new person is not able to get an internet connection.
View 9 Replies View RelatedMy advent 4489 netbook is receiving a strong wireless signal but is unable to connect to the internet.
View 1 Replies View Relatedmy advent 4213 will not connect to a mobile phone network.it has an embedded SIM.
View 1 Replies View RelatedI have an Advent Laptop running vista and I have a problem with windows suddenly not being able to find one specific wifi network. I have no problem connecting to my home network, or that of any of my friends networks.However when I go to the holiday park where I have a caravan and go into the owners lounge to use the free wifi windows can't find it. (I used to be able to connect with no problem, it's just that for some reason windows can't find it now). Everybody else in the lounge can connect with no problem.If I use my phone's usb tethering feature I can connect to the wifi network. If go into another part of the complex I can connect to the wifi there with no problem.On the park they operate two networks, one in the owners lounge, the one I can no longer connect to, and one in the cafe/bar which I can connect to.I can only assume that some 'setting' on my laptop has changed and is stopping windows finding the network, but I have no idea what it could be.
View 13 Replies View RelatedI purchased an ea6500 to replace a ea4500 about a week ago and in summary, I will be exercising the 30 return policy at the retailer, and probably never buy a cisco router again.not connected to router, and router not found messages appear alot.
Internet connectivity stops, unable to log into ea6500 completely frozen, but still routes to other LAN devices (like the SPI firewall i have the monitors network usage). then ranomdly comes back, and goes. can switch AP, and other will work, non-stop. is DEFINATELY ea6500.
sometimes I have to power cycle 6-7 times before it will maintain a wireless network that doesnt drop every 15-30 seconds.otherwise when i connect to the wireless, it log on for 10-15 seconds, then drops off and "Attempts" to reconnect.often stalls out, and crashs when USB external drive is connected at first. (again, power cycle 6-7 times to get to work properly)windows 7, and OS X 10.8 on 3 differant machines.
seems to connect better on the windows machines, and sometimes connecting with a windows machine allows apple ones to connect properly after... weird (OS X bugging up DHCP server? bacisally, when it goes down. it can take an hour to get my wireless back up, power cycle, and then see if its working proplerly, it usually isn't, try again... etc.
I want connect an external HDD 320GB FAT32 2,5" but E4200 dont found it. USB Stick with 4GB is working.E4200 have latest Firmware.
View 1 Replies View RelatedI have a series of problems I think are due to my 310N. First, with Facebook, I will suddenly be redirected to a248.e.akamai.net., which Chrome flags as an SSL error. Second, with (and only with) NYTimes.com, I will get "file not found" (and no numerical error) when trying to retrieve an article (via Chrome). AND, again only with NYTimes.com, I will get high-bit ascii characters in headlines. For other sites, I will get "invalid url" messages on web pages. If I unplug the modem and let it rest for 30 seconds, that seems to solve the problem. I have to do this at least once a day.
More than once a day. I don't think it's a 310N problem; but I've asked about this on other forums and got no useful reply. Previously I had similar problems with my 160 router. So, it's not the router. HOWEVER, shutting it off works with lot of the problems. Right now, after shutting off the router and turning it back on, now Facebook just doesn't come up at all. No error, just don't come up. I can ping it.
I get a timeout in Cisco Connect when I select "Connect USB drive". Also there is no detection through the router website. The hard drive works fine when I hook it up via USB. It's NTFS formatted. Is there any other way to make the router detect the drive? (It does recognize a USB stick, so it's no hardware issue on that side)
View 5 Replies View RelatedI have a secondary router (E1200) on my home network, connected LAN to LAN. I use it mainly for wired connections, and it does work for that. But when I try to access this router through the IP address, I get a page that says only "ACT_IDLE". Occasionally, I am able to access, but I've found no pattern to when the router is accessible and when it is not...mostly not.
View 1 Replies View RelatedI am trying to remove my BT Homehub2 and replace it with a router connected to the ADSL line using RJ11 to RJ45 cable in f0/0 configured ip address 86.177.164.200.F0/1 is configured to 192.168.1.254 (current BT Homehub IP) this is connected to my 48port cisco switch in port GI1/0/48.VLAN1 set to DHCP and my host is connected to GI1/0/2 and also configured to DHCP.Ignoring the WAP for now, what am I doing wrong? I know it will be a small IP issue somewhere, do I need to configure GI1/0/48 and GI1/0/2 with IP address'? Am I using the wrong ISP address on my routers F0/0 port?
View 2 Replies View RelatedI literally just got my hp 2000-410US notebook pc laptop and I just connected it to my Belkin router. For some reason, my new laptop would not connect to the internet even though I am connected to the router. I have another laptop which is a hp G42-410us notebook pc but it connects perfectly. I already set up my settings for the new laptop but I am not sure if I missed something during the setup that allows me to use the internet.
View 5 Replies View RelatedI recently went to a higher speed ADSL which claimed to be 16Mpbs.. It is with Acanac and when i first tested with speed net it came in over 14Mbps. I was using a netgear wireless g router (old) with the 4200 speedstream modem and got these results which I found acceptable. Now using netgear n router modem combo DGN-2000 and my readings are just over 12 Mbps. I tried reverting and still got the lower speeds. I tried isolating one computer hard wired still got the lower 12Mbps.It hasnt really affected my download speeds as far as I can tell but I did find it a little puzzling.
View 2 Replies View RelatedPlacing a second router behind a cable modem router combination.? My second router is a netgear WNR 2000 the first router is Netgear 1000.How should I configure the the WNR 2000?? Default settings?
View 1 Replies View RelatedI have used wireless routers in the past...but have just purchased a Cisco E2500. When attempting to set it up using the CD I am asked to assign name + password.....I do this and but the ?? is unable to find the router. This despite the fact that it is 8 ft. away and showing up with 5 bars on my networks available display. When I attempt to connect without going thru the setup it asks me for the password which is part of the setup process..
View 3 Replies View RelatedI thought I would leave a message on a problem. I did two chats to the support desk and this was not brought up and it is obvious. I just installed the 4200v2 as a replacement for a NetGear. I bought for the n performance and the USB for a shared disk/media file server. I connected a640G Western Digital My Book to the USB. I was able to see the drive in the asp interface of the router, but I kept getting the "error code: 0x80070035 network path not found" message. My computer is a 6 month old HP with Windows 7 running Bitdefender Internet. I found I could get to the drive from my wife's Toshiba (only used for browsing, so minimal security), so I thought it was a firewall issue (also what Cisco said). After doing some Internet mining, I found that the issue is the Netbios setting in IPv4. My PC had the setting Default, which requires the DHCP server to provide the setting and apparently this was not set by the 4200. Without Netbios the disk cannot be mapped. Changing this to NetBios "enabled" solved the problem. This can be reached by going into the Control panel:Network and Sharing Center. Click on the connection (either local area or wireless), then open the properties, click on the TCPv4, Click properties, then advanced. Go to the Win tab and select Netbios enabled.
View 1 Replies View RelatedI don't know a lot about computers. But I want to make an old Gateway 2000 G6-200 Pentium Pro wireless. I think it has windows 95 on it. So what all would I have to do to make it wireless? If I need a new hard drive what kind is compatible?
View 2 Replies View Relatedwhere is the button to turn on the wireless for a HP 2000 notebook pc?
View 1 Replies View RelatedI just bought a Netgear Router WNR 2000 v3 and installed it. I got inside the router and could set up a Network Name and security key. However, I can not access the internet when I chose a security password using WPA 2, WPA-PSK + WPA 2 PSK, or WPA/WPA 2. It only accesses the internet when I chose None.( no secured ).At this time, my network is unsecured because there isn't way I can access the internet when I create a security key using the 3 options the router offers.
Note : I have tried the 3 security options creating a key number and my computer connect to the wireless network but don't access the internet. It only access the internet when I select None ( no secured )
This is an older desktop, Been utilizing the net gear to get on the Internet for months and it was working fine,shows it is connected to ssid but ip shows up as 0.0.0.0 I have other home computers hooked up and work g so I located there ip address, can I input it myself ? If so how?
View 2 Replies View RelatedI had this card working on this notebook with Windows XP, but with only 256mb ram it ran too slow. So I went back to 2000 on it. But I can't get the card to work, I've tried using the setup, the link light on the card does flash on and off. But in the linksys program just says no association with access point and says WPC54GS is inactive. I tried just installing the driver when it detects it but that didn't work. Also I try to start the wireless configuration and just get error 1747 the authentication service is unknown. What do I need to do to get the card working on here so I have internet access?
View 5 Replies View RelatedI just bought this wireless g pci card and installed the software from the cd on to a windows 2000 pc. When I went to run the software I can only click on the exit button. I looked on the forums and saw that for win 2000 you should only install the drivers by allowing your computer to detect the card. I uninstalled the software but my computer wont detect the card now and if I reinstall the software I cant even open it up anymore. The card is not listed in the device manager at all. Would installing i the first time have created anything in the registry that would have been left behind in the uninstall and would it be blocking the computer from detecting this as new hardware?
View 9 Replies View Relatedwireless connection stop working and icon lossed on hp laptop dv 2000
View 1 Replies View RelatedThe client currently has DAS solution integrates with cisco ap1200 which has been eos. As per my knowledge DAS mobile access 2000 doesn't support. 802.11n, is this correct? We are planning to separate the dad environment with cisco. Basically positioning new 3600 n indoor AP to replace existing eos 1200. What are the pro and cons of separating two brands and solutions? Other cabling.The client having coverage issue and adding an amplifier and cable loss may add more issues to existing environment.
Also, based on experience 80211n AP are required is higher density vs 1200.What are your thoughts or best design option to separate das from WLAN environment?