My advent 4211 has intermittent wireless connectivity.I have tried resetting the channel on the hub, but have had no luck thus far. Also I have updated the driver from Realtek, but the problem persits. I have also moved the hub to another location.The thing is that I have another Laptop which has no problem connecting.
View 1 RepliesI have 2 WAP4400Ns that were manufactured in July 2007. I've experienced some problems with dropped connections even with a strong signal over the years but recently, I've had long stretches where I cannot connect wirelessly to either unit. It works for a few hours then can't connect for half the day. I have no problem connecting to their admin pages over the LAN, just wirelessly. I look at the units and the power light is steady green while the Ethernet and wireless lights flicker rapidly. This looks no different when I can connect and when I can't. Connectivity doesn't depend on location; I can put my laptop right next to one of the units when they are malfunctioning and still can't connect. I tried changing the broadcast channel but it seems to have no effect. I rentered the WEP key that I have used for years and it doesn't have any effect. Settings are pretty much factory except for changing the IP address of one of them (so they can be in the same LAN) and customizing the SSIDs and security keys.
View 3 Replies View RelatedWe are experiencing problems with Apple Ipads on a large scale network that we install and maintain, the Ipads seem to join the network with no problems (bit slower than laptops etc) but will then disconnect for no apparent reason at random intervals. We have ran laptops on the same AP's and in the same area and no similar probems occurred, we are using IOS Cisco 1041's and 1042's, we have seen one of the Ipads's sitting quite happily on a 1042 2,4ghz radio and then it disconnected and went to the 5ghz radio. We are getting similar disconnects on the single radio 1041.
View 13 Replies View RelatedI saw some other mentions online of intermittent internet connectivity using the factory-installed Intel Centrino wireless-N 1030 card on various new Dell computers running Windows 7, but didn't see any resolution to the problem.
I can connect directly to my router via an ethernet cord, but trying to use the wireless card gives me intermittent connectivity. I will pretty quickly lose the ability to load a new page if I'm browsing with IE or Firefox, and can regain it (temporarily) by disconnecting/reconnecting or letting the wireless manager troubleshoot, during which it resets the wireless adaptor. Doing a continuous ping of my router gives me anywhere from 30-70% data loss and lengthy round trips (I am currently one foot away from the router). Other (ancient!) computers work fine on my router; I have updated the router's firmware/reset it many times, etc). I didn't specifically go download a new driver for the wireless card, but going into its properties and having it search for an updated driver results in it reporting it already has the most up-to-date driver.
I spent a lot of late nights talking to Dell support, and their eventual fix (after a complete reinstall from the factory setting partition) was to set up my home network as a WEP, which I'm not happy with due to it's poor security compared to WPA2/WPA. This appeared to resolve the connectivity issue (why??). But I feel like I should be able to use WPA2 security with a brand-new laptop. So I changed it back to WPA2/WPA and tried installing all the critical updates that Windows Update could find, including SP1, and then looked at some continuous pings of various webpages and of my router itself.
Then I noticed my ping round trip time was awesome and they were 100% successful while my computer was plugged in with the power cord, but this unfailingly changed to reporting unsuccessful pings and having 1000ms round trips as soon as I disconnect the power. Seems like the on-battery power settings are starving the wireless card?
Also, I'm sure my initial intermittent connectivity (before the complete OS reinstall) was still occurring while plugged in with the power cord, so I'm not sure if the reinstall fixed some aspect of the problem, or whether the appearance of success while plugged in now is just temporary. Perhaps my card is just bad and I need a new one? I'm using the factory default power settings and the factory-installed wireless card (and I couldn't choose a different wireless card when I built my laptop)
Intermittent loss of connectivity in two level router network.Static ip address from DSL modem into WAN port of linksys wrt4g, LAN port to WAN port of dlink dir-615. All pcs, printers ans a NAS connected to the lan side of dir-615 using 16 port splitter box. Wifi set up on both routers. Router 1 is 'public' to the building, router 2 is private to the non profit org. Inermittent(1 or 2 times a week) loss of connectivity to the network and to internet.
View 18 Replies View Relatedi have the same laptop model "inspiron 15 3521". wifi used to work in a specific room, now it says "limited connectivity".
View 19 Replies View RelatedI have recently bought a new wireless card and it is giving me grief. Until now I had been using a laptop to pick up the wireless signal from my router, and pass it along to my PC, and have been receiving excellent speeds (30 Megabit) despite being 2 floors above the router.
I bought myself a Sitecom N300 card to go in the PCI slot of my computer, and my connection is generally extremely slow, and often drops completely for minutes at a time. The strange thing, however, is that it still shows medium to strong signal strength, even when the connection drops completely!
This is completely baffling me! I can't work out what could be causing interference, or why the signal strength doesn't go down when the signal does, or why the internal laptop wi-fi receiver seems so much better than this new card with 2 massive aerials. Unfortunately my ability to move either my PC or router is somewhat limited
I'm running Windows 7, fully up-to-date, and the router is a BT Home Hub 3
I have an Advent 5421 with Vista installed, it's nearly 3 years old and I have a few problems with it, but nothing too terrible, until yesterdy when I switched it on and found the wireless connection has mysteriously disappeared. When I try to connect it says there are no networks to connect to, which is obviously bollocks. The internet will now only work if I plug the cable in, which is no good as I share a flat with 2 other girls and if I do that, they lose their connection. I don't understand whats happened. I really am not computer literate at all, the only thing I tried was to make sure I had the latest software updates for my computer, which I did, but nothing happened.
View 1 Replies View Relatedi have downloaded vista to my Advent 4213 and now i can't get wireless connection to the internet?
View 2 Replies View RelatedI would like to know how to set up a wireless connection intel advent7106
View 1 Replies View RelatedI purchased an Advent DT2410 about a month ago from PC world. It came with Windows 8 OS a USB wireless stick and the following basic spec:
Intel® Core™ i5-3330 processor
Genuine Windows® 8
Memory: 8 GB
Hard drive: 2 TB
So initially brought it home, set it up and fired up connected to the internet perfectly fine with the stick. Then about once every 2/3 days, it would pick up no internet connection despite being next to the router and after 2-3 shut downs in a row would work again. When the connectivity icon was blank, I would go to trouble shoot it and windows 8 wouldn't do anything, not even attempt to detect the problems (bare in mind this PC is brand new).So I leave my home by my University and came back to my parents for Christmas. Lugged my PC back with me and set it up.So first I connected to the wireless no problems, loaded up my favorite forums and after image hovering over about 3 images the 4th would only load the top 3rd of the picture. Open up new tabs "Connecting" until:
A) Server would time out
B) Wireless would DC and then reconnect (before basically repeating the "3 image view")
C) Would work for a few hours (e.g. a streamed film) before screwing up again (rare)
So, reinstalled drivers, replaced the USB wireless stick (802.11n.) AND STILL problems problems problems. I then cleared the IP/TC stacks (I believe they're called) did it through the elevated command prompt and still nothing. So i'm using my sister's laptop to write this as my internet on my PC barely runs long enough for me to be able to check this page or download the program mentioned in the sticky.
I recently got a second hand Advent Roma 2000, which runs with Windows 7. After a while I managed to configure it to allow my T-Mobile internet dongle to connect. However, we recently got BT put in and I cannot find the wireless router [BT HomeHub 2.0].Now, at first I thought maybe the wireless detection on the router was faulty, but I checked my 360's wireless connection and that has connected with no problems.
View 13 Replies View RelatedMy advent 4489 netbook is receiving a strong wireless signal but is unable to connect to the internet.
View 1 Replies View Relatedmy advent 4213 will not connect to a mobile phone network.it has an embedded SIM.
View 1 Replies View RelatedI have an Advent Laptop running vista and I have a problem with windows suddenly not being able to find one specific wifi network. I have no problem connecting to my home network, or that of any of my friends networks.However when I go to the holiday park where I have a caravan and go into the owners lounge to use the free wifi windows can't find it. (I used to be able to connect with no problem, it's just that for some reason windows can't find it now). Everybody else in the lounge can connect with no problem.If I use my phone's usb tethering feature I can connect to the wifi network. If go into another part of the complex I can connect to the wifi there with no problem.On the park they operate two networks, one in the owners lounge, the one I can no longer connect to, and one in the cafe/bar which I can connect to.I can only assume that some 'setting' on my laptop has changed and is stopping windows finding the network, but I have no idea what it could be.
View 13 Replies View RelatedI am using this wireless router for connection to internet:http:/[url]...The problem is that in most of the time the router works without a problem then suddenly without doing anything from my side the internet connection starts intermittent and then I can’t event connect to the router. This is a screenshot of pinging the router when the problem occurs.
View 4 Replies View RelatedI've been running into an issue for the past week or so where my wireless adapter intermittently can't contact my router.When it occurs the network connection reads as having limited connectivity. I'm unable to send requests to load webpages, and videos and the like stop loading. Sometimes the network disconnects entirely. After this occurs, I can't connect again for a few minutes. My connection consistently reads as having 2-3 bars available. The issue tends to occur frequently, often every 15 minutes or so. Strangely enough, I have been able to play bf3 online for over 40 minutes without connection problems (I quit before any occurred - not sure if any would have). So far I've tried the windows troubleshooter, updating the driver to my wireless networking adapter, manually assigning my network address (tried 192.168.1.4, 192.168.1.5, etc), setting my 802.11b preamble to "Long only" and performing a system restore. I have rebooted my machine as well.
My technical specs are as follows:I'm running Windows 7 Ultimate N 64 bit edition with service pack 1. System has 8gb Ram, an i5-3570k processor and HD7850 graphics card. Motherboard is the Asrock Z77 extreme 4. My wireless network adapter is the TP-link TL-WN722N. The adapter was working fine for some time before this issue appeared.My router is an old U.S. Robotics Wireless MaxG Router. It seems to work fine with other computers in the household, although it does require fairly frequent power-cycling. Running ipconfig on the command prompt while the internet is working returns:
Quote:
Windows IP Configuration
Wireless LAN adapter Wireless Network Connection 2:
Connection-specific DNS Suffix . :
Link-local IPv6 Address . . . . . : fe80::293a:e9bb:ba5a:7536%14
IPv4 Address. . . . . . . . . . . : 192.168.2.5
[code]....
I am having trouble with my wireless internet at home, i am using a dell inspirion with windows 7, and an ipad, my router is a Netgear DGN2000, what happens is that the connection is intermittent on all the devices when using the wireless connection but no problem when using a direct connection.
These are the spec when it is working:
Windows IP Configuration
Host Name . . . . . . . . . . . . : Ericise
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No[code].....
I'm being kicked off my VPN connection back to the home office on occasion, using a Nortel VPN client. The logs show:
4/2/2013 9:58:26.883 [ENGS] -I-VerifyServerIsAlive: ISAKMP had traffic (after keepalive).
4/2/2013 9:58:27.383 [ENGS] -I-VerifyServerIsAlive: Set receivedData FALSE.
4/2/2013 9:58:28.555 [ENGS] -I-Protocol not recognized - message dropped.
4/2/2013 9:58:44.586 [ENGS] -I-Protocol not recognized - message dropped.
[code]....
the common fault seems to be DynamicDnsCleanup causing the trouble.(causes routing table to change, knocking down the VPN....) Is this a function occurring in the router? I can't find search results showing so.
I recently updated the firmware in my WRT160N V3.Ever since, the wireless signal is intermittent.It worked all day yesterday, and now today it doesn't connect at all.I can't remember exactly the settings I used to have before updating the firmware, should have written them down.From looking at articles on this site, I have the following settings:
MTU Manual 1492
MAC Adress enabled
Network Mode: Mixed
Channel Width 20MHz
Channel: 11
[code].....
I have a WRT120N router set up with WPA2 security and set to channel 11. Everything is connected via the router (one wired computer, up to a max of 5 laptops but just 2-3 on a regular basis, a wired xbox360, wireless wii and a few cell phones occasionally connect wirelessly). Everything has been working great, been getting at or very close to the 6mbps we are supposed to be getting...until the past 2 weeks. Suddenly the connection drops repeatedly throughout the night. It either shows local only or just "limited connectivity". Normally when this happens my laptop will pick the signal back up when things are normal but I am actually having to disconnect and reconnect for it to work again. It happens again in about 30 min to an hour after that. Also, our connection speeds are showing at .5 - 1.5 instead of 6. I plugged the cable modem (the 660 series sent out by sprint/embarq/century link (or whatever name they are going by today lol) into the computer directly and got 5.7mbps. I have tried power cycles of both pieces of equipment but that doesnt work.
View 3 Replies View RelatedMy router has been dropping the internet connection for years. The ethernet connection to the desktop works fine all the time. The problem is only with the wireless connection. About every 1/2 hour or so the router will drop the wireless connection and neither or my 2 laptops can find the network. Unplugging the router and replugging it in solves the problem temporarily, until it drops it again. I updated the firmware to 1.0.4 and that yielded no changes.
Router: WRT54G2 v.1 Modem: Siemens Speedster 4100 (part #060-D141-A12) My two laptops running wirelessly are Macs. The desktop is PC running Windows Vista.
Bought an E4200 to replace my Netwgear router and am experiencing the following problem.One of my wireless boxes serves as mu mail server. I've been running this configuration for years so the only thing that has changed is the router.The neworkd is up and all wireless clients can connect, but after some time, access to the mail server just 'freezes'. I say freezes as the nework icon (i'm using ubuntu' still show a connection. In addtion, there are not error in any of the logs. I just seems that the mail server and the router just stopped communication.
View 9 Replies View RelatedI have a Cisco 1242 AG wireless access point with the goal of having multiple SSIDs. I set up one network which broadcasts correctly but only sometimes can I connect to it.
And, even if I connect to the network, I cannot get a DHCP address for the client.Other devices connected (but not through this Access Point) to the associated VLAN 60 can get a DHCP address and connect just fine.Here is the configuration for the Cisco 1242 AG access point in question: [code]
Lastly, here is the information on VLAN 60 from the distribution switch. As mentioned, other devices connect to this VLAN and get IP addresses just fine.
my new E4200, replacing an E1000. In my net, at home, four computers are hooked up; 2 DELLs, 1 HP and 1 Vaio. All the computers are working fine with the new router but the VAIO notebook. I've installed the latest Firmware Version, 1.0.03. Done the new drivers on the VAIO. VAIO got intermintent net connection and nothing showed in the event logs. Worked fine with the E1000.
Sony VAIO: VPCEE45FB/BI
Windows 7 - 64bits
E4200: Firmware Version: 1.0.03
I have been having a problem with my router for the past two weeks and my ISP (RCN) has done nothing to fix it so maybe with our nerd power combined we can find a solution!My router runs fine about 60% of the time, I get 20-24Mbps down and 2Mbps up connect wirelessly. the other 40% of the time the download speed suddenly drops to 1.5-2Mbps down and 1Mbps up. There is nothing in particular that I will be doing at the moment it just suddenly dies.Things I have done that have not worked.I have changed my channel to 1,6,and 11.Updated firmware.Factory Reset (New broadcast name/password).Set up static IPs.I have tried disabling WMM Support and this just kills any connection wirelessly to the router.Is there anything else you can think of to fix the issue, or should I just be demanding a new router the next time they come
View 1 Replies View RelatedRegion : Malaysia
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : TL-WDR4300_V1_121226(Unifi)
ISP : Unifi
Recently my router have been experiencing an issue with internet connectivity with Unifi.I will be able to connect to Unifi, the status is "Connected". However after some time though, like 5 - 10 mins, I will be no longer able to browser any pages or get disconnected from online games. Checking through ping tests, I can see that I am unable to get a response. Checking the router shows that I am still connected to Unifi. After a minute or so the connectivity is restored, but the issue happens again as before. This happens with both wireless and cable. Attached is a sample of the ping test result.
Things I have tried:
Updating the firmware to the latest version
Re-configuring the modem
Re-setting the Unif credentials in the router
Downgrading the firmware
I have a brand new DAP-1522 A1 connected to an 802.11n wireless LAN in bridge mode. Running in the 2.4GHz band with WPK-2 and AES security/encryption.Everything runs fine 99% of the time, but once a day or so the wireless LAN connection on the DAP-1522 drops and then takes about two minutes to re-connect. It re-connects and then everything is fine for a day or so until the next dropped wireless connection episode on the DAP-1522. I know my 802.11n wireless network is 100% fine as during the dropped connection to the DAP-1522 I can connect directly to the 802.11n wireless network (running from my gateway/router) using my other computer, no issues.I've seen some posts on this forum that the A1 version of the DAP-1522 hardware is not 100% compatible with the 802.11n network standard and there will be intermittent wireless drops. If this is true, it's just insane. All I can say is I can't believe DLink would allow a product to be sold that won't work properly on 802.11n networks.I check the logs each time I see the dropped wireless connection and all that shows is the following.1) Negotiating connection 2) 4-way handshake success [mac address]There's no message in the logs about why the wireless connection dropped, but I assume it has something to do with re-newing a key for the wireless network as the successful key renewal messages are the only other messages in the log. When the wireless network dropped I don't see the successful key renewal message at the time I should see it.I thought this DAP-1522 would take 15 minutes to configure in bridge mode and then I'd forget about it. Spend too much time on this already, so a bit disappointed with this DAP-1522 and DLink tech support....though when it's connected to the 802.11n wireless LAN it works fine.
View 14 Replies View RelatedI recently upgraded my Linksys wrt120n router firmware & had to reconfigure settings. Subsequently, some (but not all) of my apple devices are having intermittent wireless connection problems. Specifically, my ipad1 & ipad2 never lose their connection but a mac book pro (~ 2 years old), iPhone 3g, iPhone 4, older iPod touch & very old i book g4 all work for a period of time (usually 1/2 day) & then lose their connection. When I attempt to reconnect these devices I receive the following error..."unable to join the network xxxxxx....". I also have a Dell laptop (1 1/2 yrs old) that generally does not have the connection problem. Finally, when the devices do lose their network connection all I have to do to reconnect is go to the Linkys router setup webpage & click on save & the wireless connection works again (almost like this is just refreshing the connection for these specific apple devices). I was not having any problem prior to the firmware upgrade & from what I have read the older firmware version is no longer available so going back to the old firmware does not appear to be an option.
View 1 Replies View RelatedI get cut off after about an hour online. I have cable internet and they have been out to check. I have a new modem from the company. They have put the modem on a separate wire but the problem continues.
View 1 Replies View RelatedI have reason to be suspicious as to the game's relevance. These spikes are characterized by no packet loss, as measured by pingplotter and winmtr (more specifically, there is packet loss, but I've come to understand that because it does not continue on to subsequent jumps it's not an issue), and latency leaping to between 250 and 600ms across multiple hops, seemingly without pattern or form, for intervals
Here are some summaries of some extended pingplotter sessions. The suspicion that this is not entirely WoW related is recent, so I'm working on seeing if I can get similar results from some other sources.
[code]...
I have intermittent internet access from a new laptop. When it works it is fast and consistent, but it seems there is a problem where I can sometimes start getting only part of an internet page, and then it stops downloading altogether.Below are ipconfig /all and ping tests and a screen shot of the device manager.A bit of background:1) There are 4 computers on the network, this laptop (samsung NP530) is the only one where internet is not working2) It is new, has avast installed as antivirus. Norton came with the laptop but I did not click on the button to activate it when it popped up on first opening3) A small strange thing: I get "SWMagent is restarting" message when I restart the computer. I don't know what this is.[CODE]
View 14 Replies View RelatedI have had DSL service for several years from a small, local ISP, that pays Verizon for the use of their lines. On 1/2/2012 in mid-morning I began experiencing lack of connectivity. I noticed that the "link" light on my DSL modem was blinking. I tried turning everything off & starting up again but to no avail. In the morning, I turned everything on again & for about 45 minutes my DSL service was perfect. Then it became intermittent & mostly unavailable.
View 1 Replies View Related