TP-link TL-WN722N / Intermittent Wireless Connection Timeout
Jul 14, 2012
I've been running into an issue for the past week or so where my wireless adapter intermittently can't contact my router.When it occurs the network connection reads as having limited connectivity. I'm unable to send requests to load webpages, and videos and the like stop loading. Sometimes the network disconnects entirely. After this occurs, I can't connect again for a few minutes. My connection consistently reads as having 2-3 bars available. The issue tends to occur frequently, often every 15 minutes or so. Strangely enough, I have been able to play bf3 online for over 40 minutes without connection problems (I quit before any occurred - not sure if any would have). So far I've tried the windows troubleshooter, updating the driver to my wireless networking adapter, manually assigning my network address (tried 192.168.1.4, 192.168.1.5, etc), setting my 802.11b preamble to "Long only" and performing a system restore. I have rebooted my machine as well.
My technical specs are as follows:I'm running Windows 7 Ultimate N 64 bit edition with service pack 1. System has 8gb Ram, an i5-3570k processor and HD7850 graphics card. Motherboard is the Asrock Z77 extreme 4. My wireless network adapter is the TP-link TL-WN722N. The adapter was working fine for some time before this issue appeared.My router is an old U.S. Robotics Wireless MaxG Router. It seems to work fine with other computers in the household, although it does require fairly frequent power-cycling. Running ipconfig on the command prompt while the internet is working returns:
Quote:
Windows IP Configuration
Wireless LAN adapter Wireless Network Connection 2:
Connection-specific DNS Suffix . :
Link-local IPv6 Address . . . . . : fe80::293a:e9bb:ba5a:7536%14
IPv4 Address. . . . . . . . . . . : 192.168.2.5
[code]....
View 3 Replies
ADVERTISEMENT
Apr 21, 2013
I have a brand new DAP-1522 A1 connected to an 802.11n wireless LAN in bridge mode. Running in the 2.4GHz band with WPK-2 and AES security/encryption.Everything runs fine 99% of the time, but once a day or so the wireless LAN connection on the DAP-1522 drops and then takes about two minutes to re-connect. It re-connects and then everything is fine for a day or so until the next dropped wireless connection episode on the DAP-1522. I know my 802.11n wireless network is 100% fine as during the dropped connection to the DAP-1522 I can connect directly to the 802.11n wireless network (running from my gateway/router) using my other computer, no issues.I've seen some posts on this forum that the A1 version of the DAP-1522 hardware is not 100% compatible with the 802.11n network standard and there will be intermittent wireless drops. If this is true, it's just insane. All I can say is I can't believe DLink would allow a product to be sold that won't work properly on 802.11n networks.I check the logs each time I see the dropped wireless connection and all that shows is the following.1) Negotiating connection 2) 4-way handshake success [mac address]There's no message in the logs about why the wireless connection dropped, but I assume it has something to do with re-newing a key for the wireless network as the successful key renewal messages are the only other messages in the log. When the wireless network dropped I don't see the successful key renewal message at the time I should see it.I thought this DAP-1522 would take 15 minutes to configure in bridge mode and then I'd forget about it. Spend too much time on this already, so a bit disappointed with this DAP-1522 and DLink tech support....though when it's connected to the 802.11n wireless LAN it works fine.
View 14 Replies
View Related
Dec 31, 2012
Having trouble with the TP-Link WN722N that I bought from Newegg. It doesn't show any networks on my desktop that runs on Win7. Took the drivers straight from the CD. It works fine on my other laptops and desktop.
View 4 Replies
View Related
Oct 6, 2011
Have installed a TP-Link TL-WN722N wireless USB adapter.O/Sis Win XP SP3.Np options are showing for Wireless networks under Network Connections.Wireless Zero Conifguration is on.When I run a QSS app I can see neighbours network but not my own (My equipment doesn't support QSS) so the card and driver are working.
View 7 Replies
View Related
Jul 23, 2012
I have a TP Link TL-WN722N 150mbps USB wireless adapter I use with my desktop. I've had it for about 6 months and it has been mostly fine with a few little problems. I recently went away for a few weeks and when I returned I found that my wireless adapter is running very slowly and disconecting from the router. It is an adapter problem as no one else in my house is having the same issues. When the adapter does run slowly the only way to speed it up is to unplug it and plug it in again. This puts it back to a bearable speed but usually this drops within 30 minutes.
View 1 Replies
View Related
Sep 7, 2012
I have a TP link TL-WN722N wireless adapter and it refuses to work on my win7 machine. I've tried installying the cd driver, all the relevant drivers on the TP link website, and the generic atheros driver. I've also tried manually installing all those drivers using device manager to no avail, and it says "a device attached to your system is not functioning"
But I know the physical adaptor is working because I was able to successfully install it onto another computer (it was a windows 8 preview version).
View 12 Replies
View Related
Jun 10, 2012
I am able to access 930L (2 cams) from wifi be it laptop,iphone or ipad but I am not able to see it through 3g.I have Huawei fibre optics broadband reuter from Starhub.Starhub is running away if ask them to fix it. Huawei never takes the call.I tried atleast 3 times 10 minutes each at 8006011450.It goes to disconnect. The lot talked about UPNP is enable in reuter but it does not work.
Now i talked to Dlink support with ticket DCX36811.They advised to load the firmware.I did it still the connection timeout is there. we have baby to monitor through iphone/android 3g.
View 2 Replies
View Related
Jan 10, 2012
I am having wireless connection/internet issues that are irritating me to the core!!! I have called tech support 4 times now, and I still can't get everything to play nice...I have the 655 set up as a wireless router to a Windows 7 laptop, one iPad, two iTouches, and one N3DS. I can't find a setting that will work with all devices. Here are the senarios...
1) Settings: Wireless enabled, 802.11n only, Auto Scan off-channel set to 1, Best Transmission rate, Channel Width Auto 20/40, Visible, Auto WPA Mode with AES Cipher and a pre-share key. This yields fantastic results with my laptop, it can stream video for entire episodes, and I have no problems with loading webpages in either IE or Firefox. However, it does not support the kids iTouches or N3DS.
2) Changed the above to mixed 802.11n/g AND ALSO tried 802.11 only: iTouches work and can connect to the internet, but laptop doesn't like it. I get "Problem loading webpage" every other time I access and website, and streaming stop every 5-6 minutes. Bars indicate wireless signal is strong, but intermittently get that yellow triangle.
View 11 Replies
View Related
May 13, 2012
I'm using the D-link dir-300 wi-fi router. Cable internet connection. PC is connected to the router by the cable and the laptop via wi-fi. Both machines have the same problem - after some time, although there are no package loss when I'm pinging anything, some services report "connection timeout". Such as PvP.net, EA Online and Turbofilm.tv. Soft reset, hard reset didn't solve anything. Although when PC is connected straight to the main internet cable - there are no problems at all. [code]
View 7 Replies
View Related
Jan 2, 2013
I have my desktop using a TP-Link WN722N USB wireless adapter to connect to my modem router. I get to browse for about a minute before I get dropped. Windows Network Diagnostics tells me that the problem is that the Default Gateway is not found, and then restarts the Wireless adapter, reconnects, then the cycle of browsing for a minute and disconnecting continues. None of my other computers that are wireless are facing this issue. I have the latest drivers for the wireless adapter. I have Microsoft Security Essentials installed. This is the ipconfig /all when it is connected to the internet.
[code]....
View 7 Replies
View Related
Jan 19, 2013
My previous wireless card was D-Link brand, and worked great. I never ever had trouble with connecting, never had to think about it or mess with any software. It always ran silently in the background, and connected automatically without fail. The card got damaged when I moved my computer, so I bought this T-LINK brand because it had good reviews.First I installed it from the CD the recommended way--with drivers and software. It was able to connect after some fiddling around, but then it would periodically disconnect. The problem seems to happen every 10 minutes or so, or whenever I open a game or program (like Steam), or google chrome/internet explorer, anything that requires internet usage. Sometimes it would give me an error about the settings of the card not being the same as the network settings. I think I fixed that, and still it had the same problem (it should have automatically detected the settings though).
The only way to restart it was to unplug the card, wait 10 seconds, plug it back in, or to restart my computer. However, it would soon DC again. When it does so, its like the card just goes to sleep -- no more blinking green light. Also, I made sure that the drivers that came on the installation CD are current (which they are). Eventually, after playing with settings to no avail, I uninstalled drivers and software and then restarted my computer, then reinstalled just the drivers.At first it was unable to connect, but after moving the stand to a different USB slot, then refreshing my IP through cmd, it did connect. It then DCed once on its own. I was able to get it back up after pulling the card out of the USB stand and plugging it back in. Since then it has not DCed, but I am not holding my breath.
First I have to say, I absolutely hate the program that came with it. Windows does everything the program does, except 100% better. I am not surprised that its not DCing as much with just the drivers.Ah, I spoke too soon. While writing this post, I attempted to open a new tab in google and it temporarily DCed me five times in a row. Specifically, there is a little yellow triangle over a 5-bars good signal. Says it is connected (limited connectivity). This time, the little green light stays blinking. It eventually re-connected itself each time on its own (maybe when the IP refreshed itself?). Each time it happened I was trying to use google searchThe 6th time I was in the middle of watching a video on youtube (not sure it makes a difference). The DCing seems to happen a lot more when I am actually using the connection. Sometimes I cannot load a web page even when it
says I am "connected"[CODE]
View 2 Replies
View Related
Nov 23, 2011
Just bought myself a TP-Link WN722N Wirless Adapter. Currently I have a Netgear WNA3100 connected which works fine but I to use the TP-Link to connect to a second network simultaneously.Here's the problem.The drivers installed just fine for the TP-Link adapter. Windows shows that its connected as a USB device (USB2.0 WLAN) and Network & Sharing Centre shows it is being "Wireless Network Connection 4"(The Netgear one shows as "Wireless Network Connection 2")However, when i try to use the TP-Link one to connect to a network, it doesn't show up in the "Network Connections" menu on the Taskbar, and when i disconnect the Netgear one it says that it can't find any wireless connections at all; note that "Network & Sharing Centre" still shows the TP-Link Adapter as being connected to the PC).Tried Reinstalling the TP-Link Software, updating it, etc. Restarted PC. Disabled Netgear connection. Physically Disconnected Netgear Adapter and still no luck.
View 2 Replies
View Related
Oct 6, 2011
recently my network adapter just stopped working. The wifi signal was really bad so i unplugged it and when i plugged it back in it doesnt even turn on. I've reinstalled the drivers and still it doesn't turn on. In device manager there is a yellow exclamation mark next to it and when i click on properties it says code 10. I used it on my laptop and it turns on but when i plug it in my desktop it doesn't seem to turn on.
View 1 Replies
View Related
Jan 24, 2013
I am using this wireless router for connection to internet:http:/[url]...The problem is that in most of the time the router works without a problem then suddenly without doing anything from my side the internet connection starts intermittent and then I can’t event connect to the router. This is a screenshot of pinging the router when the problem occurs.
View 4 Replies
View Related
Dec 21, 2012
I am having trouble with my wireless internet at home, i am using a dell inspirion with windows 7, and an ipad, my router is a Netgear DGN2000, what happens is that the connection is intermittent on all the devices when using the wireless connection but no problem when using a direct connection.
These are the spec when it is working:
Windows IP Configuration
Host Name . . . . . . . . . . . . : Ericise
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No[code].....
View 1 Replies
View Related
Apr 25, 2012
My router has been dropping the internet connection for years. The ethernet connection to the desktop works fine all the time. The problem is only with the wireless connection. About every 1/2 hour or so the router will drop the wireless connection and neither or my 2 laptops can find the network. Unplugging the router and replugging it in solves the problem temporarily, until it drops it again. I updated the firmware to 1.0.4 and that yielded no changes.
Router: WRT54G2 v.1 Modem: Siemens Speedster 4100 (part #060-D141-A12) My two laptops running wirelessly are Macs. The desktop is PC running Windows Vista.
View 2 Replies
View Related
May 25, 2012
Bought an E4200 to replace my Netwgear router and am experiencing the following problem.One of my wireless boxes serves as mu mail server. I've been running this configuration for years so the only thing that has changed is the router.The neworkd is up and all wireless clients can connect, but after some time, access to the mail server just 'freezes'. I say freezes as the nework icon (i'm using ubuntu' still show a connection. In addtion, there are not error in any of the logs. I just seems that the mail server and the router just stopped communication.
View 9 Replies
View Related
Oct 15, 2012
I have a Cisco 1242 AG wireless access point with the goal of having multiple SSIDs. I set up one network which broadcasts correctly but only sometimes can I connect to it.
And, even if I connect to the network, I cannot get a DHCP address for the client.Other devices connected (but not through this Access Point) to the associated VLAN 60 can get a DHCP address and connect just fine.Here is the configuration for the Cisco 1242 AG access point in question: [code]
Lastly, here is the information on VLAN 60 from the distribution switch. As mentioned, other devices connect to this VLAN and get IP addresses just fine.
View 11 Replies
View Related
Feb 9, 2013
Region : Malaysia
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : TL-WDR4300_V1_121226(Unifi)
ISP : Unifi
Recently my router have been experiencing an issue with internet connectivity with Unifi.I will be able to connect to Unifi, the status is "Connected". However after some time though, like 5 - 10 mins, I will be no longer able to browser any pages or get disconnected from online games. Checking through ping tests, I can see that I am unable to get a response. Checking the router shows that I am still connected to Unifi. After a minute or so the connectivity is restored, but the issue happens again as before. This happens with both wireless and cable. Attached is a sample of the ping test result.
Things I have tried:
Updating the firmware to the latest version
Re-configuring the modem
Re-setting the Unif credentials in the router
Downgrading the firmware
View 4 Replies
View Related
Oct 16, 2011
my new E4200, replacing an E1000. In my net, at home, four computers are hooked up; 2 DELLs, 1 HP and 1 Vaio. All the computers are working fine with the new router but the VAIO notebook. I've installed the latest Firmware Version, 1.0.03. Done the new drivers on the VAIO. VAIO got intermintent net connection and nothing showed in the event logs. Worked fine with the E1000.
Sony VAIO: VPCEE45FB/BI
Windows 7 - 64bits
E4200: Firmware Version: 1.0.03
View 1 Replies
View Related
Dec 3, 2011
I recently upgraded my Linksys wrt120n router firmware & had to reconfigure settings. Subsequently, some (but not all) of my apple devices are having intermittent wireless connection problems. Specifically, my ipad1 & ipad2 never lose their connection but a mac book pro (~ 2 years old), iPhone 3g, iPhone 4, older iPod touch & very old i book g4 all work for a period of time (usually 1/2 day) & then lose their connection. When I attempt to reconnect these devices I receive the following error..."unable to join the network xxxxxx....". I also have a Dell laptop (1 1/2 yrs old) that generally does not have the connection problem. Finally, when the devices do lose their network connection all I have to do to reconnect is go to the Linkys router setup webpage & click on save & the wireless connection works again (almost like this is just refreshing the connection for these specific apple devices). I was not having any problem prior to the firmware upgrade & from what I have read the older firmware version is no longer available so going back to the old firmware does not appear to be an option.
View 1 Replies
View Related
Mar 12, 2013
Region : Vietnam
Model : TL-WR841N
Hardware Version : V8
Firmware Version :
ISP : VNPT on Vietnam
I have bought WR841 V8.3. Signal show is good, but i ping to router many timeout or delay when i open some website. Ping only geog when i near router.(some time delay)
View 2 Replies
View Related
Feb 29, 2012
I was able to connect to my 5ghz and 2.4ghz networks just fine. Now today I get a message that the connection timed out whenever I try and connect to the 5ghz. I have done a 30/30/30 reset, and still no joy. The one thing I haven't done yet is a 30/30/30 with a configuration from scratch. I will probably try that later. I've done the usual things like change the channel and all that, still no go. Other things I've done, change the network name, change the MTU, restart my machine. However, this is happening on other devices as well. The 2.4ghz network, solid as a rock.
View 1 Replies
View Related
Jul 30, 2012
When a client connecting to a specific AP (example AP01), after every 1800 sec uptime it will reconnect and join other unit AP (example AP02)Both AP physically installed distance is around 6 meters from each other. I conduct the testing where i get myself sitting in middle between these two APs.
01. If i disable settsion timeout this feature, or setting the seconds become higher value, what's the performance and security impact? Is it recomend to change the default 1800 seconds session timeout?
02. Is there anyway i can tweak on WLC controller to prevent the client after session timeout then associate with another AP. This will lead major performance impact as the client woudl possibility connect to the weak signal AP and effect on the performance.
These are the details for reference:Client detail
- Dell DW1520 wireless-N WLAN card, with firmware version 5.100.235.12
- CCX version 4 supported
- Layer 2 security is WPA2 personal with PSK.
- wireless radio an
Controller detail:
model is AIR-CT5508-K9
software version is 7.2.110.0
View 4 Replies
View Related
Mar 11, 2011
I get cut off after about an hour online. I have cable internet and they have been out to check. I have a new modem from the company. They have put the modem on a separate wire but the problem continues.
View 1 Replies
View Related
Dec 5, 2011
My laptop is connected to an Internet cable inside my apartment building for access to a free Internet service provided by the building management.The high speed cable service works okay for a few days but then after say 4 or 5 days it starts to slow down and then on the 6th or 7 day I can no longer connect using the cable. The technician in my building doesnt speak such good English and claims it is a software problem in Windows itself in my laptop ,but I don't know what would cause the software to trigger this condition?The last time the technician told me to go through some steps but I have to admit I have forgotten the very last ones in the " procedure " and how to complete the final steps of the procedure :-
He said to :-
1. Right click on the computer icon on the desktop
2. click on device manager
2. click on " network adapters " these are shown as being " Atheros AR8152/8158 PCI-E Fast Ethernet Controller ( NDIS 6.20 ) and secondly " Realtek RTL8188CE Wireless LAN 802.11 PCI-E NIC "
4. After that he told me to " refresh " the connection but I have forgotten how to do so?The wireless connection is working okay but I have noticed once this fault happens to the cable connection, the wireless connection doesn't work either until I unplug the cable. Then I can connect to the wireless Internet connection. But if I leave the cable in then neither the cable or the wireless works?
View 4 Replies
View Related
Apr 18, 2012
Im currently experiencing an intermittent connection on my office and we just upgraded from 4Mbps to 10Mbps. Latency is high when pinging commercial website like yahoo.com,it shoots up to 200sec. ISP router is connected to two HP Procurve Switch, then the workstation and servers. Already did a router/modem test and it failed, I advise our ISP to change the router but it were still experiencing the same problem. Network drop is also experience even after office hours, eventhough only few workstations are working.
View 1 Replies
View Related
Dec 2, 2012
I have build a new pc this week. All was fine offline. After connecting to the Internet initially everything loads quickly however sometimes after turning on my pc or restarting it the Internet just refuses to load. Pages take forever then I get a message unable to connect however the connection is still active and all my other devices work ipad etc. after a few times restarting or leaving it for a while all is fine.
View 1 Replies
View Related
Apr 12, 2011
I work in a small school and recently we started to have a problem with browsing the internet. We don't have an 'IT Department' as such as I'm the closest thing to it.When a browser is opened it will not connect to the homepage, or if it does its generally from cache, instead an error message about not being able to connect to server will appear. Now if you hit refresh you might or might not connect to the webpage in question but you can gurantee that it will take a long time to make that connection even on an undemanding site like wikipedia.The odd thing is that when connected to a speed checker it gives no surprising results, speed is normal. Also when downloading a file or the latest linux live distribution torrent I can achieve maximum speeds available to us.We use a selecction of Macs & PCs mostly connecting through ethernet cabling although connecting wirelessly is no different. We use BT 2Wire 2700HGV Business Hubs. I can't think of any changes our end that have happened to cause this and our internal network connections run just fine. I have tried pinging from the command line and it looks ok to my limited expertise, no lost packets.
View 3 Replies
View Related
Feb 24, 2012
Intermittent loss of connectivity in two level router network.Static ip address from DSL modem into WAN port of linksys wrt4g, LAN port to WAN port of dlink dir-615. All pcs, printers ans a NAS connected to the lan side of dir-615 using 16 port splitter box. Wifi set up on both routers. Router 1 is 'public' to the building, router 2 is private to the non profit org. Inermittent(1 or 2 times a week) loss of connectivity to the network and to internet.
View 18 Replies
View Related
Jul 17, 2012
I've been having a problem for a while now wherein my internet connection seems to randomly drop for anywhere from ten seconds to a minute, then come back online. It's been doing this over the lifespan of one router, and continued into the life of this new one I have, which is a WNDR3700v3 Netgear.
I called my ISP and they fiddled around with things on my computer, but the issue is still going on. Rather than slog through another three hours with them, does anyone here have any tips for what I might look into for the cause?
View 19 Replies
View Related
Jan 5, 2013
I was previously with sky and never faced any bother with my wireless broadband. Recently to my regret we moved broadband (amongst other utilities)to Utility Warehouse (UTW) who's broadband is through Telecom Plus. Anyway since joining with them I have had no end of bother with intermittent internet connection. Sometimes we get a stationary green broadband light then after a little while then we get a flashing green broadband light. We are constantly either pin resetting the router or switching it on and off at the rear, where it will work for a small amount of time then connection is lost again. The router that they have given us is a technicolor tg582n Pro. We have had two of these as originally we thought that the router could be faulty but obviously that is not the problem as even the second one is dropping our connection. We bought another filter incase that was the problem and even tried plugging router directly into phone box and still didnt work. Utility Warehouse have been about as much use as a chocolate teapot and we are so <unhappy> that we are paying for a service that does not work? They said that our cordless phones could be interfering with the signal? Is this maybe the case and the phones are running on same channel as router thus causing interference? We had these same phones when we with sky and they never caused interference with our broadband. I was going to try connecting my laptop via ethernet cable to router. Sometimes the landline crackles (since UTW installed a new landline & new tel number) so it could even be that? UTW will not send an enginneer out to check their line. we are at our wits end, about to cancel their broadband and go back to reliable sky.
View 8 Replies
View Related
Nov 26, 2012
ASA 8.2(5), uauth absolute timeout is disabled and inactivity timeout is set to 48 hours:
timeout xlate 48:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:00:00 absolute uauth 48:00:00 inactivity
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
Users still get kicked out every 8 hours and they have to reauth. This is a logging message:
%ASA-5-109012: Authen Session End: user 'john', sid 839, elapsed 28801 seconds
View 1 Replies
View Related