ISP Cable in Smart box. 4 cat 5 cables from various rooms in house to feed cable ready TV's and one from my computer room. Can I connect all cat 5's to switch that is connected to cable modem located in Smart box and connect Wireless Router to cat 5 in the computer room and expect router to work properly?
View 4 RepliesI have a Modem/Router combo and am trying to plug an 8 port switch directly into it and then have wireless AP's and other hardwired devices plugged into the switch. Normally, when I plug a switch into a router it requires no set up. This one on the other hand, will not work.
View 7 Replies View RelatedI am trying to open port 12000 on my sky dlink router, been trying for a few days now and i just can't nail it. When i log into router, it brings up the sky router page, any one ever setup port 12000 on the sky router page.
View 1 Replies View Relatedhow do I hook up a router and a switch together to my cable modem
View 3 Replies View Relatedhow do I get my hard drive to work thru my belkin router usb port?
View 1 Replies View Relateddifference between a gigabit switch router and a normal router google email harvesting edited by moderator:removed email addy to protect from spam
View 1 Replies View RelatedI've had my network up and running for several years with no issues. Last week I upgraded my router to a Dlink 826L and now anything connected to my downstream Dlink DSS16+ can't be accessed.
View 3 Replies View RelatedI attached an Iomego Home Media network hard drive to my Linksys E3000 router (via ethernet cable). Before setting up the remote access on the Iomega, I forwarded the ports that it wanted (443 and 21) to the static IP of the Iomega. I checked to see that they were open using yougetsignal.com and they were both open. After setting up the remote access on the Iomega, the 443 port closed and I cant even get into the "manage storage device" page for the Iomega. Iomega uses TZo for the domain names. They tell me that the association is made between the name and my public IP address. My router is out of warranty since Sept, so Linksys wont give me the time of day. I contacted my ISP and while they block a couple of ports, 443 is not one of them.I've installed the latest firmware (1.0.04 - Build 6). Reset and rebooted numerous times, Port 443 remains closed.
View 8 Replies View RelatedI have a Cisco 1841 router with the followingSerial T1 connection Fastethernet 1 with network address 192.168.0.1 Fastethernet 2 with network address 198.168.0.1I want to isolate Fastethernet 2 so that it cannot access the internet or the 192.168.0.1 network. Only incoming request is available.
View 5 Replies View RelatedHow do I port forward on a SAGEMCOM SE567 router to be able to view my DVR from a remote location?
View 3 Replies View RelatedI have a Huawei 523a Router at the moment and I'm trying to setup a IP camera.The Router doesnt allow port forwarding, so my question is can I add another Router onto the Huawei router to allow the second one to work my camera
View 10 Replies View RelatedWe just purchased 8 managed switches POE to swap out our existing in preparation for our new phone system. We installed them all after configuring with static IP. Deployed... and all but two work fine. Any tips for troubleshooting why two of them do not work? There are a couple other switches in the building. Could it be that a switch "upstream" from the two non-functioning switches is causing an issue? If so, how do I find out? When we put back the two "dumb" switches all was fine.
View 1 Replies View RelatedI have an ESW 520 8-Port switch with a management ip address of 192.168.10.2 /24 After I reboot it, I can successfully ping it from a pc with an ip of 192.168.10.123 for about 50 consecutive times.After that, I get a "Destination host unreachable" (this icmp message is sent by my pinging pc (192.168.10.123).This obviously seems like a bug.Whenever I reboot it, it goes through the same sequence.
View 2 Replies View Relatedmodem
........ |
........ |
----switch-----
|................ |
|................ |
Router 1.... Router 2
|..................... |
|..................... |
Computer 1.....Computer 2
......................Computer 3 Router 1 points to a VPNRouter 2 access to the internetComputer 3 needs to access router 1 (VPN). Both Computer 2 and 3 are in a different room than computer 1, and router 1. Computer 2 is networked via cat5e to router 2.Is is possible to have Computer 2 and 3 share the cat5e, yet access different routers?
I have a sge 2000 24 port POE switch that won't boot, won't communicate on console or TCP/IP, and all of the port lights are lit up green. Holding down the reset button doesn't fix the issue and there aren't any lights illuminated on the left hand side of the switch.
View 1 Replies View RelatedIs this smart switch possible to do Mac Filtering? how to enable mac filtering on this device?
View 1 Replies View RelatedI have sample lab dhcp-client ------- (vlan62) sg-300 switch (vlan62) ------ dhcp server
When I set on switch :
dhcp relay : enable
option 82 : enable
dhcp server address: ip of dhcp
When debug packets from client to server, there is no 82 option in dhcp discover packets. I mirror all traffic to mirror port with wireshark. I can see dhcp packets but without option 82.
Firmware version: 1.0.0.27
I want to configure my SRW248G4 switch thru console port. Unfortunately in this switch there is no RJ45 console port input, I can only see cosole port that is look like RS232 input. I bought two standard cisco console cables that have one end with db9 and one with RJ45.
Now I have and idea to put one end of one cable (db9) to switch, and one end (db9) of second cable in my computer (COM input/output)
I need to connect two RJ45 together - this is not a problem, I know how to do this. Here is the question :I know how pinout in my computer look like but i can't find pinout of console port in my SRW248G4. There is many pictures in Internet, for many Cisco devices but this isn't working. Maybe in LINKSYS pinout look different ?
We have recently purchased SG 300-52Port Cisco Switch to support our Network but they constantly having some bizarre issues or I assume bugs, i.e. we cannot Telnet nor SSH to the switch now, whereas we were able to SSH before, we have set them up for Remote Log Services to get some syslogs and reports but no report have been generated nor logs,
I have done some testing through Wireshark and there are absolutely no reports / logs.We have some real issues with this switch and it’s hard to believe that this is a Cisco Product,
SG 300-52 Port Gigabit Managed Switch
Firmware Version (Active Image ) : 1.1.1.8
Firmware Version (Non-active ) : 1.1.0.73
Boot Version : 1.0.0.4
I am trying to configure port-channel from one switch to two switchs, and only one interface of each switches make part of the port channel.Cisco IOS Software, ME380x Software (ME380x-UNIVERSALK9-M), Version 12.2(52)EY4, RELEASE SOFTWARE (fc1) [code]
View 5 Replies View Relatedhow many concurrent voice call can be conducted at once with the cisco sf 100d-08 8-port 10100 switch?
View 1 Replies View RelatedHow to configure SF300 48port switch as DHCP Server or not.
My Configuration as below
I have 8 vlan configure in SF300 (SVI with ip address)isit possible to configure dhcp server and how i can apply access-list to restrict with other vlans.
I am trying get inter vlan routing to work on a DF 300 - 24 port switch. I have an existing company network on 192.168.111.0 and want to create a vlan on 192.168.1.1 that can talk to 192.168.111.0. I have enabled layer 3 routing on the switch via console and also provided the ip routing command. I have the following VLAN's:
VLAN1 - Default 192.168.111.0
VLAN2 - 192.168.1.0
I have enabled DNS and provided my two DNS servers 192.168.111.82 & 192.168.111.212. I have set the VLAN1 interface to 192.168.111.217 and VLAN2 interface to 192.168.1.1.
Ports FE1 - FE15 are set to access ports and assigned to VLAN1 (untagged)
Ports FE16 - FE24 are set to access ports and assigned to VLAN2 (untagged)
I have set a default route for the switch to 0.0.0.0 0.0.0.0 192.168.111.254 (Draytek 2600 router). I have connected a computer (A) to VLAN1 port FE3 and a computer (B) to VLAN2 port FE16. I have set Computer A default gateway to 192.168.111.217 and its IP address to 192.168.111.94. I have set Computer B default gateway to 192.168.1.1 and IP to 192.168.1.2.
Computer A has access to Mdaemon, file server via network drives but no internet (cannot ping google) and can ping computer B and RDP onto computer B.
Computer B can ping computer A and RDP onto computer A but does not have access to the company network i.e MDaemon, file server etc. It also cannot access the internet.
From the console I can ping [URL]and all ip addresses in the company network i.e. 192.168.111.82 (DNS server). If I scan computer A wirh wireshark the internet starts working weird!
Configuration show below:
switch7c0a71#show run
vlan database
vlan 2
exit
voice vlan oui-table add 0001e3 Siemens_AG_phone________
voice vlan oui-table add 00036b Cisco_phone_____________
voice vlan oui-table add 00096e Avaya___________________
[code]....
I have my network with severals SG300 switches.I have one of them like my core switch working in layer 3 mode. With 2 vlans and vlan interfaces to each vlan.Everything is working ok.But now i have to connect one 3com unmanage switch that have host from vlan 1 and 2. How should i connect this switch to my Cisco sg300 switch?
[code]...
we have cisco 6500 series switch and configured port channel on both switches with 2 gig interfaces on both switches.
When we enable the port channel mode to as desirable to the interfaces on both side and applied the port channel to physical interfaces switch will go down and if we remove on any one side switch will come up. we have enabled globally the following commands. [code]
I bought an ESW 540 8-port switch, mainly for the POE capability over all 8 ports, so that we can power some SPA50X phones.The concepts of a "managed" switch are challenging for a newbie.Is there a way to make this device behave like a boring "unmanaged" switch ??We have plenty of bandwidth, and don't need to be troubled by QoS and virtual LAN's, or all the security stuff at this time.Making this device work like an unmanaged switch (aka plug-and-pray).
View 2 Replies View RelatedI can't access my live camera feed from my home surveillance DVR from outside of my LAN using the Linksys E4200. I was able to access the camera feed using the Linksys WRT 610N, when it wasn't dying on me. I can access the camera feed from inside of my LAN. I've configured port forwarding, port range triggering, and DMZ. I'm using the LTS LTD7708 DVR.
View 1 Replies View RelatedI have switch.Broadband connection i want to share it among all 5PCs.By ising ICS and switch can do it??
View 1 Replies View RelatedI can telnet to switch from checkpoint firewall access port and from switch directly. I can ping/traceroute successfully to the switch. Access-lists 14 & 15 are allowing the traffic I want. The router on the other side of the FW has 2 static routes and a default static route set up.
Here is some of the config from my switch:service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryptionhostname xxxxx
enable secret xxxxxx
username xxxxxxxx password xxxxxxxip domain-name xx.xx.netaaa new-model
aaa authentication login default local enable line none[code].....
Not sure of checkpoint firewall config....I have run wireshark when trying to telnet and I get no syn-ack back from remote switch. Just 3 consecutive syn attempts.I have some switches I can connect to and they go right through the 3 way TCP handshake and I cannot find any differences in the configs between the successful connections and the unsuccessful connections.
where can I get RAD SPS-12 X-25 switch manuals?
View 2 Replies View RelatedI volunteer at a school who just purchased two 48 port SGE2010 managed switches. I am not a big fan of the web gui and was hoping to see the standard Cisco command prompt instead of the menu-type interface.
Is there a way to view the MAC table showing which MAC address is plugged into which port on the switch? I have been fighting with the menu and the gui for a while now and do not see this anywhere.
I have two windows 2008 machines on vmware. I assign 10.0.0.1/8 and 10.0.0.2/8 to them. Both connected to same virtual switch. Now should these two PCs ping each other? In my case they dont ping. What i get is Repy from <ip address>: Destination host unreachable.
View 2 Replies View Relatedwith server , laser printer , adsl modem and desktp computer
View 2 Replies View Related