Cisco WAN :: 7613 How To Adjust Change Over Buffer Size At Link-set Sub-command
Apr 13, 2011
I was wondering about command of Linkset subcommand at ITP7613.I have been using the Cisco7613 chassis for the ITP(SIGTRAN) service.
However, i know that the "tx-queue-depth" command is used for sctp multihoming buffersize that between primary and secondary path at the Link sub-command mode. but i can't adjust the changeover buffersize(retrieval buffer) that between link and another link at the Linkset subcommand mode.
It's above my comprehension.
My guess is that related to "plan-capacity-rcvd" command. it's right?I want to know command that adjust the buffersize of Link changeover.
View 0 Replies
ADVERTISEMENT
Feb 9, 2013
We phace disconnections when having a dozen open connections.Does the Cisco devices have a documented limitation on the buffer size or the number of telnet connections?
View 1 Replies
View Related
Jan 15, 2012
Is there any way to check how much of the total buffer size is utlized at any given moment out of the total space or memory allocated in Cisco 4500 switch For eg - show logging output is as below for a 4500 switch
Syslog logging: enabled (0 messages dropped, 1 messages rate-limited, 0 flushes, 0 overruns, xml disabled, filtering disabled)
Buffer logging: level debugging, 31644 messages logged, xml disabled, filtering disabled
Exception Logging: size (8192 bytes)
From above is there any command to check hw much size is currently utlized , by 31644 messages ..or how much of the located buffer size is utilized.
View 3 Replies
View Related
Mar 11, 2013
Cisco Prime LMS 4.2.3 is sending SNMP request too big for asa interface buffer.LMS is running on Windows server incoming SNMP request (528 bytes) from IP address x.x.x.x Port 50592 Interface "inside" exceeds data buffer size, discarding this SNMP request.
212005: incoming SNMP request (%d bytes) from %s exceeds data buffer size, discarding this SNMP request. It is very much like this error
Error Message %PIX-3-212005: incoming SNMP request (number bytes) on interface interface_name exceeds data buffer size, discarding this SNMP request.
#Explanation This is an SNMP message. This message reports that the length of the incoming SNMP request, destined for the firewall, exceeds the size of the internal data buffer (512 bytes) used for storing the request during internal processing; therefore, the firewall is unable to process this request. This does not affect the SNMP traffic passing through the firewall via any interface.
#Recommended Action Have the SNMP management station resend the request with a shorter length, for example, instead of querying multiple MIB variables in one request, try querying only one MIB variable in a request. This may involve modifying the configuration of the SNMP manager software.
how do I change the SNMP request size in LMS? I can only find the following that might be an option
[URL]
just using default settings with snmpv3
View 1 Replies
View Related
Aug 9, 2012
First is it possible to change the length that new files will be created? Right now it creates 1 minute chunks which becomes a pain in the butt to manage. I would really like to set the length to 10min or even 60min chunks as one minute is just to short. I use the camera for constant recording and do not plan on puttin in a computer to record to due to logistics.
Secondly, is there software that will manage these files? That is pull down from the cameras SD and archive then allow you to simply play from any location via mouse or time picker?
I have used professional security systems in the past and know that this is just an entry home consumer camera but was hoping it had a little more functionality, as it stands the built in SD recording is almost useless without some sort of management software.
View 2 Replies
View Related
May 6, 2012
I just needed more insite into the function of the ip tcp adjust-mss command which can be used to adjust the MSS value in the tcp syn packet which passes that interface. But here is a question which I had. Consider that i have two sets of systems in my LAN one with an MTU value of 1300 ( MSS 1260 ) and with a MTU of 1500 ( MSS -1460 ). If I go ahead and put an ip tcp adjust-mss 1456 (for reducing the packet size from 1500 to 1496) on the WAN . Does the command only lower the MSS for the set of systems which have 1460 or will it also increase the MSS in the tcp syn packets send by systems with MSS of 1260 ( which can potentially break some communication ).
View 1 Replies
View Related
Oct 24, 2011
Our 2811 WAN router is experiencing a high volume for huge buffer misses with some failures. Should we look into the automatic buffer tuning command as our IOS supports it. Does the router need to be reloaded after? Has anyone experienced any issues with this command or having traffic dropped (even biped)?
This HourTodayOut-Of-Memory Errors0 misses 0 misses Small Buffer Misses0 misses 80 misses Medium Buffer Misses0 misses 15 misses Big Buffer Misses0 misses 0 misses Large Buffer Misses0 misses 0 misses Huge Buffer Misses12745 misses 110224 misses
Buffer elements: 1118 in free list (1119 max allowed) 1277770169 hits, 0 misses, 619 created
[ code]....
View 1 Replies
View Related
Apr 8, 2013
I was asked to performe upgrade from acs 5.3 to 5.4 (vm), but i noticed that someone installed it on 80gb partition and there is 500gb as one of the requriments in upgrade and install procedure. What is strange to me is that "dir disk:" command shows such an output: 5165345067 bytes available.And under ESX i see 80gb partition. Anyway, is there any way to extend partition size to 500gb? Can I just change it under ESX? Is there any procedure to take under ACS console?
View 1 Replies
View Related
Nov 6, 2011
I'm having a problem with a context, I have two CISCO ASA 5550 (failover) and also we have the CISCO CSM to monitoring it, but since some weeks is showing a memory usage of 100% but then it drops until reach zero and then again the graphic goes up. This is the second time that the graphic shows this
I also check this on the CLI and i'ts fine because is showing the real percent, so my question here is why is showing this kind of behavior, I mean it was working fine before.
In the other hand I checked the secondary device and this is showing a 99% of used memory, but as the other one this graphic doesn't drop
I also checked via CLI and it says that it had the 99% memory used , Is there a way that i can put more memory on the context or what do you suggest that I can check on my firewalls.
View 1 Replies
View Related
Mar 15, 2011
I have recently up swapped out an 877 router for an 887 router and have copied the config template accross however it will not take 3 of my commands.
AAA accounting system default stop-mly group tacas+
ip inspect name firewall cuseeme timeout 3600
dsl operating -mode auto
View 2 Replies
View Related
May 3, 2013
i have 4507R with dual supervisors (WS-X4013+10GE) with IOS cat4500-ipbasek9-mz.122-46.SG.bin the supervisor module are in 3 and 4, and I want to connection port 5, but i have interface and line protocol down "inactive" error.
So I realized to use command "hw-module" to change the module to GE port. However, I am not able to use the command as" I cannot use the command "hw-module uplink" as well.
View 2 Replies
View Related
Oct 12, 2011
I am switching a switch connecting to the ASA5550 tomorrow. My current switch is using fiber connecting to the ASA. The new one only support copper. If I switch between fiber to copper on the ASA (change media-type command on interface) will it cause a down time? I have VPN tunnel on the ASA and don't want the session to reset.
View 2 Replies
View Related
Feb 14, 2013
I am currently setting up a 2800 Series router, and prefer a username/password type authentication rather than a single enable password. To do this, I did:
Router(config)# username <myuser> privilege 15 secret 0 <mypassword>
Router(config)# username2 <myuser> privilege 15 secret 0 <mypassword>
Router(config)# aaa new-model
Router(config)# aaa authentication login default local
This basically does what I want - when I connect to the router through console, it immediately asks me for a username and password. The thing is - as soon as I provide the right credentials, it takes me to USER EXEC mode (the default command mode). Is it possible to change that so that after entering the credentials, I go right into privileged exec mode?
Bonus question: As it is now, I just have no enable password, so when I login with my credentials, I issue "enable" to enter privileged exec mode without it prompting for an additional password. Is it safe to do it this way - having no enable password but requiring a username and password for login?
View 3 Replies
View Related
Feb 7, 2012
we have a Nam module on a 7613. I have access to the router. but how can i know the how to access the Nam?
View 1 Replies
View Related
Aug 4, 2011
We have built some policers to apply to vlan SVIs on our 7613 so that we can rate limit input and output traffic. We followed the Cisco formula and got this.
policy-map vlan-shape-3meg
class class-default
police cir 3000000 bc 562500 be 1125000 conform-action transmit exceed-action drop violate-action drop
There have been some complaints about this not actually meeting the limit. When I do a show policy-map interface xxx I get this. Based on that it looks like the Be value is being change to match the Bc value.
On a separate note, I noticed that every policer we built with the cisco formula actually ends up with a Tc greater than the max Tc of .125 seconds. It seems odd that a recommended formula would end up creating values outside the maximum allowed limits by the software.
I'm not a QoS expert so if any of this seems like basic stuff it's just because I'm a little slow on QoS.
Vlan2
Service-policy input: temp-remove
class-map: class-default (match-any)
Match: any
police :
[code]....
One other thing...in order to apply policers input and output on an SVI does mls qos vlan-based have to be configured on the trunks tagged with the corresponding Vlan?
View 1 Replies
View Related
Feb 5, 2007
I have a cisco 7613 router and need to connect a site using Optical fibre (BSNL) on gigabit port,we will use convertor to convert optical signal to electrical .What configuration must be done on router to ensure this point to point fibre connectivity between my router and another router at differnt POp.
View 7 Replies
View Related
Apr 25, 2012
I have Cisco 7613 on my edge(MPLS Backbone). CPU utilization is shooting to 100% at frequent intervals. When I tell vendors managing device they tell that it is happening due to one of my server(connected on Fast ethernet port of 100Mbps) generating heavy traffic. My questions are:
1. Can a router of 720Gbps capability be choked due to traffic generated by 100Mbps link?
2. Interrupt CPU process utilization is well below 10% at the said time. BGP router process consumes most of the CPU. Does this means that server in question is generating too many routing updates?
3. Is there any way that I can limit routing updates on a particular link?
4. how to check which link is causing more CPU utilization.
View 8 Replies
View Related
Jan 4, 2011
We have a 7613 w/ WS-SUP720-3BXL running 12.2(18)SXF11. We have a 48 port WS-X6748-GE-TX that has one interface that keeps getting output drops for anything over 200Mb/sec.
See the attached file which has more details and show results.
View 1 Replies
View Related
Apr 9, 2011
page extends over sides of monitor
View 1 Replies
View Related
Apr 28, 2012
I am using a GRE-IPSEC tunnel configuration + EIGRP routing protocol and I would like to confirm if I am right with the following:
Due to I am configuring the IP MTU = 1400 in the Tunnel interface, I am avoiding additional fragmentation after GRE encapsulation because there is enough room for IPSEC encapsulation (no matter which mode I am using - I am considering the worst case Tunnel Mode). However, I would like to know what happens if I ALSO include in the Tunnel configuration the command ip tcp adjust-mss 1360 which is clear operates in layer 4 during the 3 way handshaking process to establish the TCP connection/session between opposite hosts (in this case the interaction is with the respective end routers). By adding this MSS command, I understand that I could also eliminate the initial fragmentation of the 1500 bytes LAN packets (before GRE encap) because the hosts are notified to send 1360 bytes packets to the Router and based on the previous, I would be able to transfer packets without "theorical" fragmentation between both ends.
One more question, how can affect if I include this additional command (TCP ADJUST-MSS) the performance (process + memory) of a router 3845 or 7200 without producing for example a entire crash of the device???. I understand that this TCP MSS negotiation is router process intensive but is less than IPSEC encryption/decryption.
View 19 Replies
View Related
Feb 13, 2011
I have been using the Cisco7613 and FlexWAN with PA-8E1-IMA PortAdapter.It has been used for ITP (SIGTRAN) Today, I attemted to enter the Port Adapter 13 1 module with using command that "attach" command.But I couldn't that. and I could see the Error Message below." RTTYC_ ATTACH_ REQ Failed with return code 2 , aborting". This Module (13 1) is working normal. but why cannot enter to the PA ?
View 3 Replies
View Related
Feb 24, 2013
What would cause an interface to show up/up (looped), but you still can't ping that loop?...It is on a Cisco 7613 with an Enhanced FlexWan (WS-X6582- 2PA), with a Mx Serial PA, 8 ports (73-1580-10) and running IOS ver 12.2(33)SRE2 [code]
View 5 Replies
View Related
Feb 25, 2005
I got a problem when I try to create a VLAN in a 7613 router. The screen capature like the following:
router(conf)#vlan 1045
router(conf-vlan)#exit
VLAN(s) are not available in Port Manager
The VLAN is failed to create. The VLAN range which is failed to create is from 1001 - 1060.
View 3 Replies
View Related
Mar 20, 2012
We have Router CISCO7613,SSO redundancy configured with two Sup 720-3BXL running 12.2(33)SRC1 image. Even thought I've configured SSO, my standby sup remains in COLD state with the following logs generated.
Mar 20 22:07:32.514 IST: %ISSU-SP-3-PEER_IMAGE_INCOMPATIBLE: Peer image (c7600s72033_sp-ADVENTERPRISEK9-M), version (12.2(33)SRC1) on peer uid (8) is incompatible
Mar 20 22:07:32.514 IST: %ISSU-SP-3-PEER_IMAGE_INCOMPATIBLE: Peer image (c7600s72033_sp-ADVENTERPRISEK9-M), version (12.2(33)SRC1) on peer uid (8) is incompatible
Mar 20 22:08:48.263 IST: %PFREDUN-SP-4-INCOMPATIBLE: Defaulting to RPR mode (Runtime incompatible)
[code]...
These logs says that due to some reasons, the configuration is not being synchronized with active and standby sups and hence the redundancy mode remains in RPR mode and SSO not achieved, and hence COLD state. However, I couldn't find a reason why the configuration is not being synchronized, I've issued the command, redundancy config-sync ignore mismatched-commands, and everything worked fine, SSO achieved and standby sup came to HOT state.Now my query is,
1. Why the configuration was not synchronized and standby SUP got in COLD state??
2. Since I issued the suggested command, at least, some of the mismatched lines in configuration will be ignored, Will that create a problem when my Active sup fails and standby become active?
View 4 Replies
View Related
Apr 4, 2013
I am planning to deploye the fwsm with all this complexity, will this type of senario work or not means traffic will move from msfc to the core.. Is this right to create another svi int2 on msfc to move traffic from msfc to core-switch.
G0/1(cisco7613) Vlan10----Vlan10(inside)FWSM-(outside)vlan20---Vlan20(inside)(svi-int1)MSFC(outside)(svi-int2)Vlan30---Vlan 30G0/2(Core-Switch)-----internet--->
View 5 Replies
View Related
Oct 20, 2011
How to adjust picture on monitor when it is too far to the left of screen? I cannot see the Start menu on the monitor screen.
View 2 Replies
View Related
Jan 3, 2012
i want my wifi connection all the way to my room
View 1 Replies
View Related
Jun 12, 2013
I have 2504 WLC with a few access points. the problem is when the PC's go in sleep mode, the users have to re-authenticate when they log in again Is there any way to let the PC's automatically re-authenticate without the user having to type in the credentials again?I have web authentication configured for this SSID and authentication is using the WLC local Data base.
View 6 Replies
View Related
Feb 5, 2013
I need your opinion regarding moving of IDSM -2 and FWSM Module from 7613 to 6513 chassis.Currently these two modules are in 7613 and we are not using either of them now we have to configure them in 6513 chassis. As you can see from the figure that traffic of all 3 core router i.e 7613 go to 6513 - to proxy ISA 2004 - 6513 - to Internet.
There are also some network attached with 6513 and we want to move both of modules to 6513 so that NetworkA/B/C/D/E which are attached to 6513 can also be configured for FWSM and IDSM -2.
I have a query regarding this migration:Do we need license for these two modules again for 6513 chassis?
View 2 Replies
View Related
Mar 8, 2012
My laptop was working fine.Yesterday, I installed VS2008, Google Chrome, and MSDN.Today, when I start my laptop, the screen brightness goes very low when I reach the "enter your Windows 7 password" page.
I have a Sony Vaio vgn-nr11s/s Also, my wireless connection and LAN seems to have vanished into thin air.
View 1 Replies
View Related
Mar 12, 2013
is there any specific way to create the SVI Interface on MSFC , actually I need to create the two SVI Int on MSFC to enable routing in between two VLANs on 7613 chassis.
View 2 Replies
View Related
Mar 30, 2013
I'm currently looking at buying the E1200. confirm if the settings on this router allow you to adjust the TX (aka transmission strength)?
View 3 Replies
View Related
Jul 6, 2013
I have a dell inspiron N5040 laptop and i can't seem to adjust the brightness of my monitor, what driver or what do i need to download for this ?
View 1 Replies
View Related
