I have been using the Cisco7613 and FlexWAN with PA-8E1-IMA PortAdapter.It has been used for ITP (SIGTRAN) Today, I attemted to enter the Port Adapter 13 1 module with using command that "attach" command.But I couldn't that. and I could see the Error Message below." RTTYC_ ATTACH_ REQ Failed with return code 2 , aborting". This Module (13 1) is working normal. but why cannot enter to the PA ?
View 3 RepliesWe have Router CISCO7613,SSO redundancy configured with two Sup 720-3BXL running 12.2(33)SRC1 image. Even thought I've configured SSO, my standby sup remains in COLD state with the following logs generated.
Mar 20 22:07:32.514 IST: %ISSU-SP-3-PEER_IMAGE_INCOMPATIBLE: Peer image (c7600s72033_sp-ADVENTERPRISEK9-M), version (12.2(33)SRC1) on peer uid (8) is incompatible
Mar 20 22:07:32.514 IST: %ISSU-SP-3-PEER_IMAGE_INCOMPATIBLE: Peer image (c7600s72033_sp-ADVENTERPRISEK9-M), version (12.2(33)SRC1) on peer uid (8) is incompatible
Mar 20 22:08:48.263 IST: %PFREDUN-SP-4-INCOMPATIBLE: Defaulting to RPR mode (Runtime incompatible)
[code]...
These logs says that due to some reasons, the configuration is not being synchronized with active and standby sups and hence the redundancy mode remains in RPR mode and SSO not achieved, and hence COLD state. However, I couldn't find a reason why the configuration is not being synchronized, I've issued the command, redundancy config-sync ignore mismatched-commands, and everything worked fine, SSO achieved and standby sup came to HOT state.Now my query is,
1. Why the configuration was not synchronized and standby SUP got in COLD state??
2. Since I issued the suggested command, at least, some of the mismatched lines in configuration will be ignored, Will that create a problem when my Active sup fails and standby become active?
i have an issue for collect data on adapter 1, that don´t collect data but see that adapter 2 if collect data on module 4.
monitor session 1 source vlan 102 rx
monitor session 1 destination analysis-module 4 data-port 1
monitor session 2 source vlan 106 rx
monitor session 2 destination analysis-module 4 data-port 2
I reconfigured newly monitor and continues with that issue. Always ok by data-port 2.
- show version Cisco 6513
Cisco IOS Software, s72033_rp Software (s72033_rp-ADVENTERPRISEK9_WAN-M), Version 12.2(33)SXH7, RELEASE SOFTWARE (fc3)
. show version NAM
NAM application image version: 3.5(1b)
- sh module
Ports Card Type Model
----- -------------------------------------- ------------------
8 Network Analysis Module WS-SVC-NAM-2
Hw Fw Sw Status
------ ------------ ------------ -------
2.0 7.2(1) 3.5(1b) Ok
I got a problem when I try to create a VLAN in a 7613 router. The screen capature like the following:
router(conf)#vlan 1045
router(conf-vlan)#exit
VLAN(s) are not available in Port Manager
The VLAN is failed to create. The VLAN range which is failed to create is from 1001 - 1060.
I changed my router from Belkin F5D 7633-4 (G) to Belkin F5D 8636-4 v2 (N) on the 7633 I was able to set up virtual server page and access my CCTV cameras remotely with no problem but on the 8636 with the same info into virtual servers page I get "No 1 WAN address is invalid".The format of the page is slightly different the 7633 required "inbound Port" number to be put in twice in different boxes side by side and the same with "Private Port".The 8636 has only one box to enter the port number under each heading.
View 3 Replies View Relatedwe have a Nam module on a 7613. I have access to the router. but how can i know the how to access the Nam?
View 1 Replies View RelatedWe have built some policers to apply to vlan SVIs on our 7613 so that we can rate limit input and output traffic. We followed the Cisco formula and got this.
policy-map vlan-shape-3meg
class class-default
police cir 3000000 bc 562500 be 1125000 conform-action transmit exceed-action drop violate-action drop
There have been some complaints about this not actually meeting the limit. When I do a show policy-map interface xxx I get this. Based on that it looks like the Be value is being change to match the Bc value.
On a separate note, I noticed that every policer we built with the cisco formula actually ends up with a Tc greater than the max Tc of .125 seconds. It seems odd that a recommended formula would end up creating values outside the maximum allowed limits by the software.
I'm not a QoS expert so if any of this seems like basic stuff it's just because I'm a little slow on QoS.
Vlan2
Service-policy input: temp-remove
class-map: class-default (match-any)
Match: any
police :
[code]....
One other thing...in order to apply policers input and output on an SVI does mls qos vlan-based have to be configured on the trunks tagged with the corresponding Vlan?
I have a cisco 6509 configured with a cisco NAM module. I have reset the config of the NAM module by the config clear command. Since this moment I can't no more ping the NAM module via the management port: OK via the 127.0.0.91 address and log in ok via the ios cli session command. [code] I have already tried to reboot the module via the ios cli hw module command and nothing better.
View 12 Replies View RelatedI am going to install new Nexus 7K. Installed SUP and one 32-Port 10Gb module. When I open the box to install this 10Gb module, I saw that there is a carbon paper is tighted with ***** on the top of the module. confirm either it will insert in Switch with carbon paper or have to remove this carbon paper?
View 1 Replies View RelatedI have a cisco 7613 router and need to connect a site using Optical fibre (BSNL) on gigabit port,we will use convertor to convert optical signal to electrical .What configuration must be done on router to ensure this point to point fibre connectivity between my router and another router at differnt POp.
View 7 Replies View RelatedI've got a pair of N7010's in a vPC domain with some FEX's attach running NX-OS 6.0.2. I am experiencing port failures on my N7K-M132XP-12L module the port got shut down due to internal errors with Error Disabled status and I am not able to bring the port back up. I am getting the following errors when I try to reset it. I am hoping is not hardware related as my vPC peer-link is on this module and I only have a single N7K-M1 32 XP-12L in each N7010. Replacing the module will be painful. [code]
View 7 Replies View RelatedMy questions is can a 4 port PoE switch module (EHWIC-4ESG-P) and a 8 port switch module (EHWIC-D-8ESG) be used at the same time in a Cisco 1941 router?
View 1 Replies View RelatedI have a laptop with a single physical NIC which I have used the advanced management tools to create two virtual NICs (say vlan 10 and vlan 20) and both are on the same subnet (say 192.168.4.x). One NIC is for normal TCP/IP traffic and one is for broadcast/multicast traffic (I have some custom software that requires this to be the case and works fine on an older laptops with built-in physical NIC and PCMCIA XIRCOM NIC). The dual NIC laptop communicates with a dual NIC server via a Cisco 2811 router (which has a 16 port switch module at the back) and has vlans set up so.
What I want is for the single NIC laptop (with two virtual NICs) to be able to also communicate with the server. Basically, one NIC is for normal traffic and one is for multicast/broadcast traffic. All three machines need to be able to talk to each other using the NIC for normal traffic and both laptops must be able to receive broadcasts from the server. What is the best way to configure the router to handle the trunking/tagging? Most configuration documentation I read has two complete subnets for the two virtual NICs. Note that all three machines use static IPs and are part of a workgroup so no DNS and domain servers etc.
i have 4507R with dual supervisors (WS-X4013+10GE) with IOS cat4500-ipbasek9-mz.122-46.SG.bin the supervisor module are in 3 and 4, and I want to connection port 5, but i have interface and line protocol down "inactive" error.
So I realized to use command "hw-module" to change the module to GE port. However, I am not able to use the command as" I cannot use the command "hw-module uplink" as well.
We have recently purchased a Cisco 4506 that has several Gigabit Ethernet modules installed.One of the Ethernet Gigabit modules - a WS-X4424-GB-RJ45 - is being picky with who it talks to at Gigabit Ethernet.
If I plug a laptop into one of it's RJ45 ports using a Cat 6 cable, nothing happens. No link light, no notification of link up or down on port statistics, absolutely nothing.If I plug a server into the same port it works fine at Gigabit Ethernet (even using the same Cat 6 cable).I can get the module to recognize a laptop if I fix the speed/duplex on the laptop to 100Mb/Full. I have tried this with other staff laptops from different vendors (HP / Dell / etc.) all with the same result.
The module directly underneath this module - a WS-X4448-GB-RJ45 - works fine for both laptops and servers. We have tried swapping the module positions but to no avail.
I have Cisco 7613 on my edge(MPLS Backbone). CPU utilization is shooting to 100% at frequent intervals. When I tell vendors managing device they tell that it is happening due to one of my server(connected on Fast ethernet port of 100Mbps) generating heavy traffic. My questions are:
1. Can a router of 720Gbps capability be choked due to traffic generated by 100Mbps link?
2. Interrupt CPU process utilization is well below 10% at the said time. BGP router process consumes most of the CPU. Does this means that server in question is generating too many routing updates?
3. Is there any way that I can limit routing updates on a particular link?
4. how to check which link is causing more CPU utilization.
We have a 7613 w/ WS-SUP720-3BXL running 12.2(18)SXF11. We have a 48 port WS-X6748-GE-TX that has one interface that keeps getting output drops for anything over 200Mb/sec.
See the attached file which has more details and show results.
We have two 6509 switches with one WS-X6704-10GE module in each of them. There is an optical cable between the two switches plugged in WS-X6704-10GE module on both sides. When you shut down the port on one side the other port still stays as up and you need phisycally to unplug the cable to have it down. The same behaviour is seen no matter on which of the two switches you shut down the port, the opposite one always stays as up and only removal of the cable makes it go down.
The ports are configured quite simply:
interface TenGigabitEthernet1/1
switchport
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1-10
no ip address
udld port
The IOS version is 12.2(18)SXF8
I have a 3925 Router with a 48 port switch module (part number SM-D-ES3G-48-P). I have no problem accessing the 3925 Router, but when I go into the 48 port, I get an error that reads
Error Hardware not supported by firmware. Try loading a newer software instead. System Resetting...
I know that the wrong IOS is installed on the switch, but the problem is that this is an endless loop. The switch resets then comes back to the same error. How to get the switch out of this loop so that I can load the correct IOS.
I have a 6500 switch and i recently removed a module (line card) from the switch. The problem is that the port configurations of the removed module still exhists in running configuration. I was not aware of the right procedure,[URL] however, i would like to know whether it resolves if i reboot the switch.
View 1 Replies View RelatedI have a 1941 that I am going to deploy with a HWIC-D-9ESW switch module (I only need 3 switch ports but need the PoE). I am going to hang a 1262 autonomous AP off one of the ports but I need to configure MAC address port-security so that only that AP can pass traffic. I know the switch modules are 'almost' exactly like a switch for commands but I can't seem to enable or configure any port-security settings. Is port-security no available on the switch modules?
View 3 Replies View RelatedWe have a core switch with the following ios and supervisor engine. Can we add a16 port LR (x2)or LRM(X2) ON the core switch?if not what modifications has to be done?if an ios upgrade is necessary is it a costly affair?At present we have two 1gb up link modules in single and multimode fiber .
#sh moduleMod Ports Card Type Model Serial No.--- ----- -------------------------------------- ------------------ ----------- 1 16 SFM-capable 16 port 1000mb GBIC WS-X6516A-GBIC SAL0803T308 2 48 SFM-capable 48 port 10/100/1000mb RJ45 WS-X6548-GE-TX SAD07500600 5 5 Supervisor Engine 720 10GE (Active) VS-S720-10G SAL1439UMZK
#sh versionCisco IOS Software, s72033_rp Software (s72033_rp-IPBASE-M), Version 12.2(33)SXI4a, RELEASE SOFTWARE (fc2)Technical Support: [URL] Copyright (c) 1986-2010 by Cisco Systems, Inc.Compiled Fri 16-Jul-10 19:51 by prod_rel_team
ROM: System Bootstrap, Version 12.2(17r)SX7, RELEASE SOFTWARE (fc1) uptime is 1 year, 27 weeks, 4 days, 23 hours, 30 minutesUptime for this control processor is 1 year, 27 weeks, 4 days, 22 hours, 58 minutes(code)
What would cause an interface to show up/up (looped), but you still can't ping that loop?...It is on a Cisco 7613 with an Enhanced FlexWan (WS-X6582- 2PA), with a Mx Serial PA, 8 ports (73-1580-10) and running IOS ver 12.2(33)SRE2 [code]
View 5 Replies View RelatedI am planning to deploye the fwsm with all this complexity, will this type of senario work or not means traffic will move from msfc to the core.. Is this right to create another svi int2 on msfc to move traffic from msfc to core-switch.
G0/1(cisco7613) Vlan10----Vlan10(inside)FWSM-(outside)vlan20---Vlan20(inside)(svi-int1)MSFC(outside)(svi-int2)Vlan30---Vlan 30G0/2(Core-Switch)-----internet--->
I need your opinion regarding moving of IDSM -2 and FWSM Module from 7613 to 6513 chassis.Currently these two modules are in 7613 and we are not using either of them now we have to configure them in 6513 chassis. As you can see from the figure that traffic of all 3 core router i.e 7613 go to 6513 - to proxy ISA 2004 - 6513 - to Internet.
There are also some network attached with 6513 and we want to move both of modules to 6513 so that NetworkA/B/C/D/E which are attached to 6513 can also be configured for FWSM and IDSM -2.
I have a query regarding this migration:Do we need license for these two modules again for 6513 chassis?
is there any specific way to create the SVI Interface on MSFC , actually I need to create the two SVI Int on MSFC to enable routing in between two VLANs on 7613 chassis.
View 2 Replies View RelatedI was wondering about command of Linkset subcommand at ITP7613.I have been using the Cisco7613 chassis for the ITP(SIGTRAN) service.
However, i know that the "tx-queue-depth" command is used for sctp multihoming buffersize that between primary and secondary path at the Link sub-command mode. but i can't adjust the changeover buffersize(retrieval buffer) that between link and another link at the Linkset subcommand mode.
It's above my comprehension.
My guess is that related to "plan-capacity-rcvd" command. it's right?I want to know command that adjust the buffersize of Link changeover.
Can you configure a Cisco 1941 to use an 8 port EHWic module and the 2 onboard GE ports in a single LAN?
I've discovered you can't have the on GE ports associated with a VLan, and I'm when I've previously researched for a solution, bridging was mentioned but I cannot seem to get it to work (or completely understand it)The reason I would like to use all 10 ports on for the LAN is becuase I have 10 devices I need to connect to the 1941?
I'm using PA-SON-OC3 on 7200VXR (NPE-G1). I want to upgrade the link to OC12 with same wavelenght. I found PA-SRP-OC12SMI for this purpose but I'm not sure about compatiblity.
View 2 Replies View RelatedI am using 3660 Router, all cards are working fine as expected but NM-2FE2W is booted & then down. Following error is occurred in show diag "Port adapter is disabled deactivated".I have reset the card as well as router, changed the slot of card, but the problem is not resolved.
View 8 Replies View RelatedFrom what I have found the VPN (WS-IPSEC-3) port adapter (on a WS-SSC-600) is not supported if you decide to turn the 6509-E into a VSS system.
View 2 Replies View RelatedIs there any solution for automatic switching between wired and wireless network connection?
In my work we have two option for connection to network. Wired for working but with blocked pages like youtube and other streaming media. And wireless for visitors which haven't blocked any pages but I can't do my work on it. Can I by connected to both and some utility will doing switching between them? I want to use streaming and be connected to wired network which has blocked streaming.
I use Dell vostro 3550 as wireless spot but I'm have a problem with "WiFi mini port adapter". , when i try to enable "Intel My WiFi technology" . it's enable but WiFi card die after few minute, i can't see any signal of wireless network.....and of course,
my phone not see the signal wireless by my laptop. This problem appeared two months ago, before I use it very normal. I try reinstall driver wireless, window but ---> nothing change. My card wireless: Intel(R) Centrino(R) Wireless-N 1030.