I am using 3660 Router, all cards are working fine as expected but NM-2FE2W is booted & then down. Following error is occurred in show diag "Port adapter is disabled deactivated".I have reset the card as well as router, changed the slot of card, but the problem is not resolved.
View 8 RepliesI am having a problem getting serial interfaces to show up with a NM4A/S card in a 3745 router. It worked at first but now the serial interfaces don't show up in running-config but show diag shows the card is present but says "Port adapter is disabled deactivated". I have tried the card in 3 different slots and of course turned off power when moving card around (left power cord in for grounding). Again, it was once working (serial interfaces were showing up in running-config) so if I damaged the slot somehow, however I was very careful when seating card. Have been searching the learning network and google for days now to no avail. Have tried to find something similar to the card type command thinking the port adapter needs to be activated but have not found any documentation about that. Hope card isn't bad all of a sudden but really don't think it is since it worked before and it seems to be recognized just not showing serial interfaces in running-config/sh ip int b (on ios/cli). Really think it's something along the lines of activating card, but not sure.
View 1 Replies View RelatedI am facing low relaiblity issue in one of the ethernet port even no link is connected to that port.
Router model : cisco 3660
IOS - c3660-ik8s-mz.122-24a.bin
Ethernet1/2 is up, line protocol is down
Hardware is AmdP2, address is 0007.85fb.c312 (bia 0007.85fb.c312)
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
[Code]...
I am using Windows 7, suddenly my network adapter has been deleted and i am unable to use Internet
View 7 Replies View RelatedOn my Toshiba A105, the wireless adapter (Intel PRO/Wireless 3945ABG) is disabled. When I ask it to be Enabled, it goes through the motions but then immediately disables it again.
View 2 Replies View RelatedI have a windows 7 laptop and when I connect it the a wired connection it disables the wireless & 3G connections, but when I unplug the cable it doesn't renable the connections, I have to go into the network connections and select each one and renable it again.
View 6 Replies View Relatedwhenever I troubleshoot a random internet connection shut off, the diagnostic is "Local Cable Connection 2 Adapter is disabled." Weirdest part is that I am connecting via WiFi.I've had this problem since college freshman year (I am a college junior). It only occurs at school, but the school tried fixing it and "everything" works fine. The internet basically shuts off every hour or so. It's tedious to sign back on and starting this year, I am starting to use a program that requires online internet connectivity for the program to function.
View 3 Replies View RelatedI am having a HP Laptop with Windows Vista 64 bit OS. Since today I am having problem with my wireless network adapter card. It is remaining disabled and not getting enabled. I uninstalled the driver as well as disable the card but it is not working. The problem is Quick launch button on HP laptop for wireless card is showing as enabled but my network center shows it as disabled.
View 1 Replies View RelatedMy computer can no longer connect to the internet. As I do not use an Ethernet cable, my concern is the wireless aspect. I am running Windows 7 on an HP laptop, and when I troubleshoot the problem all it pops up with is "Local Area Connection 4 adapter is disabled". When I try repairs as an administrator it just repeats the fact that the adapter is disabled, but does not provide a way for me to fix this. I have also tried going through Control Panel > All Control Panel Items > Troubleshooting > Network and Internet and selecting the network adapter option, selecting the Local Area Connection 4 to diagnose. It then said troubleshooting couldn't identify a problem.
View 2 Replies View RelatedLinksys has disabled my wireless adaptor for wireless devices such as my Netflix streaming movie player. They are asking for my routers user name and password which I am not accessing right, I get "401 Authorization required" How do I factory restore my router? It's a D-Link DES-1105 router model BEFW1154V4. I need to enable my network for wireless connection. How to get my routers user name and password? I 've had my Netflix player hooked up and working for almost a year and have never encountered this problem. Im going to purchase a linksys wireless adaptor the first of the month with having a secure connection to linksys instead of having to wait all day for wireless linksys with the Ativa adaptor I already have?
View 2 Replies View RelatedI successfully installed the AirLink101 AWLL6075 Adapter, however it cannot find networks because the Wireless Monitor section is always checked as being "Disabled". When I uncheck the box, a few seconds later it comes right back to Disabled with the check mark again.
View 14 Replies View RelatedOne of our Cisco 3750G switches keeps showing this warning:
Description: Gi4/0/43: Unexpected BPDU received. Port has been Disabled.
Recommendation: Check Configuration of the switch, also make sure devices connected to the switch. Enable this port again.
However, there is no thing connecting to the port Gi4/0/43 as shown this link: [URL]. Why do you get this warning?
I have an SG-200-8 which connects to a stacked pair of SG500-28P switches. It is powered by PoE from the SG500. From the SG500 the port appears Up, but at the the SG200 it is disabled and nothing I do re-enables it. I know the cable is good because I had a previous netgear switch hanging off it and working, also the power gets through.I can only connect to the switch if I disable wifi and plugin a manually configured PC - DHCP doesn't get through to it from the SG500 end.I have tried a second SG200 same problem. Have disabled RSTP/ STP thinking it might to relate to the fact that a PC connected to the switch also had a wifi connection to the same LAN, but. Don't know where to go next. looks like a bug?
View 1 Replies View RelatedI have just gotten a new touch phone that has wifi. and i wanna use it through my dlink dir-825 router. My phone is the nexus s with 2.3 andriod OS.The problem is that my phone can see the 2.4 ghz connection it just keeps reporting "deactivated" i did acess other wifi and used the internet over a router. So i know the phone works.
So my question is: 1. Can i make my router ONLY be in 2.4ghz mode, if so, can you link or explain it?
Since I moved our WLC Controller ( 5508 ) from Version 7.0 to Version 7.2.111.3 I got above failure messages. Until now I changed the radius timeout from 2 to 10 seconds and also I disabled the aggressive failover without success. What else it could be ?
View 3 Replies View RelatedI have a wap200 wireless access point configured and connected to the switch 2690 switch on vlan1, when I connect the wireless access points to the switch the port become disabled.
View 1 Replies View RelatedI've got a pair of N7010's in a vPC domain with some FEX's attach running NX-OS 6.0.2. I am experiencing port failures on my N7K-M132XP-12L module the port got shut down due to internal errors with Error Disabled status and I am not able to bring the port back up. I am getting the following errors when I try to reset it. I am hoping is not hardware related as my vPC peer-link is on this module and I only have a single N7K-M1 32 XP-12L in each N7010. Replacing the module will be painful. [code]
View 7 Replies View RelatedI've got two two 3560s switchs, (WS-C3560G-48TS-S) that I'm trying to connect to each other using the GB ports over Fibre. We purchased the following GBICs, SFP 1000SX Transceiver and when we put them in the port it shows (err-disabled). Below is some information I pulled from one of the ports, but doesn't matter what port I use they all say the same thing.
ProdSwitchSW1#show run int g0/51
Building configuration...
Current configuration : 37 bytes
!
interface GigabitEthernet0/51
end
[code]....
Configuration register is 0xF
Using a Mac running Mac OS X 10.6.8 with VPN Tracker 6.3.0.Before switching to the WAG320N I had no issues with my IPSEC VPN client. After the switch it consistently fails in Phase 1 negotiation.In the log file of the gateway I only notice: Mon, 2011-08-22 07:47:31 - [Outgoing] UDP Packet - 192.168.1.100:500 --> IP.ADDRESS.VPN.GATEWAY:500.The software itself complains about timeouts while contacting the remote gateway.VPN pass through is enabled, no port forwarding is set up, firewall is disabled.
View 6 Replies View RelatedAs the subject says, I've hooked up a Samsung BD player to a BEFSR41 router. The router has the current firmware version. When I run the connection test for the player, the local connection is good but the Internet connection fails and the message is " The HTTP port is disabled."
I've searched high and low for a solution to no avail. I did searches on the forum and couldn't find anything. As a test, I connected the BD player directly to the DSL modem and the Internet connection worked perfectly so it appears that the blockage is within the router.
I've serched through the router setup and have changed most settings to try and find something that would work. Nothing worked so I have returned my setup to its original state.
I am wanting to take my cable internet connect and give it to the other to networks and be able to communicate between the two networks. I believe this can be accomplished by IP routing, but have no clue on how to do it. What I would need to input into the 3660 to make it work? Right now the 3660 has the factory default setup, I haven't configured anything on that yet.
View 3 Replies View RelatedI have two LANs in my house, one 10/100 base and the other 10/100/1000, but one internet connection that I would like to have access to on both networks. Right now I have two Belkin routers for each network. In addition I have a Cisco 2600 and 3660. I know they are old, but they seem to be in operational order. Can I use those to combine to two networks? The only thing I want to maintain is the speed on the gig network, from the router to the PC's and devices.
View 6 Replies View RelatedI need data sheet ( technical sheet) for Cisco3660-MB-2FE router.
View 6 Replies View RelatedI think I might have a problem with how my network is set up.
Cable Modem --->ASA5505--->Cisco 3660--->Switch For some reason if I use the ASA as a DHCP server too, the internet is much faster. Could the 3660 be slowing down the netwok? The 3660 has 2 FE ports, so it should be running good at 10/100 correct? Is there another setup I should consider to speed up the network? [code]
I am having a problem with my cisco 3660 router. I have installed a wic 2T interface card and every time i set it to "no shutdown" the interface always went down and keep getting the following message " %FECPM-2-SCCFAIL: Init of SCC2 for int 0/0 failed to do fecpm_dma_init" .
View 2 Replies View RelatedI am troubleshooting interface resets on a 3660 connected to a 3550 over Fast Ethernet. I have hard coded both sides for full duplex and 100Mbit. The 3660 is incrementing interface resetes about 4-6 times a day and the 3550 is clean. I have noticed this in other similar configurations as well.
View 4 Replies View RelatedHow filter inbound routes in Cisco ASA OSPF? Because Cisco ASA has no "distibute-list" command for OSFP process configuration, I try to use "filter-list" command in area definition. So, I try to use next configuration:
R1 (Cisco 3660):
skip
!
router ospf 1
[Code].....
I have a good working knowledge of TCP/IP networking. I have a Cisco 3660 router I'm wanting to use in place of a WRT54G router with my Charter cable internet service. I saw a youtube video where a guy demonstrated how to use a Cisco 2600 series router with home broadband service. I followed the video to setup my 3660 router. I can ping the LAN side (192.168.1.1) with no problem, the DHCP functions as it should. I can see activity on the on the WAN port indicator but no internet access. I have attached .doc file that shows the "sho run" info. My network will be setup as follows Charter Cable Motorola Surf Modem - ethernet to MM fiber converter - MM fiber over to Sun Microsystems cabinet fiber closet - MM fiber card (on Cisco 3660 router FA6/0 WAN interface) - LAN interface FA0/0 - Cisco 3524 managed switch. One of the gigabit MM fiber ports on the Cisco 3524 feeds a 3Com Superstack 12 port gigabit fiber managed switch. My two Dell 2950 servers will be on the Superstack gigabit fiber backbone. The Cisco 3524 10/100 ports will have a Cisco access point, two IP addressible battery backup units, two Dell Desktops, and a LG Blu Ray player.
View 21 Replies View RelatedI am using cisco c3660 to act as Terminal Server for the communication of production machines in my company, recently there is a communication lost issue happen and its due to physical cable unplug from the machine. to troubleshoot for this issues i have to physically go inside my production area to check on it, as i understand from vendor we can check on the physical machine to see whether the LED light on the module is green or not, but in case of need to troubleshoot at night time, its time consuming as i need to travel back to company. is there any command that i can issue in the router c3660 to check on the physical connection between c3660 router and the production machine? the IOS version is IOS (tm) 3600 Software (C3660-I-M), Version 12.1(4)
View 3 Replies View RelatedI'm using PA-SON-OC3 on 7200VXR (NPE-G1). I want to upgrade the link to OC12 with same wavelenght. I found PA-SRP-OC12SMI for this purpose but I'm not sure about compatiblity.
View 2 Replies View RelatedI have been using the Cisco7613 and FlexWAN with PA-8E1-IMA PortAdapter.It has been used for ITP (SIGTRAN) Today, I attemted to enter the Port Adapter 13 1 module with using command that "attach" command.But I couldn't that. and I could see the Error Message below." RTTYC_ ATTACH_ REQ Failed with return code 2 , aborting". This Module (13 1) is working normal. but why cannot enter to the PA ?
View 3 Replies View RelatedFrom what I have found the VPN (WS-IPSEC-3) port adapter (on a WS-SSC-600) is not supported if you decide to turn the 6509-E into a VSS system.
View 2 Replies View RelatedIs there any solution for automatic switching between wired and wireless network connection?
In my work we have two option for connection to network. Wired for working but with blocked pages like youtube and other streaming media. And wireless for visitors which haven't blocked any pages but I can't do my work on it. Can I by connected to both and some utility will doing switching between them? I want to use streaming and be connected to wired network which has blocked streaming.