Cisco Switching/Routing :: WRT54G / 3660 For Home Cable Broadband Use?
May 26, 2013
I have a good working knowledge of TCP/IP networking. I have a Cisco 3660 router I'm wanting to use in place of a WRT54G router with my Charter cable internet service. I saw a youtube video where a guy demonstrated how to use a Cisco 2600 series router with home broadband service. I followed the video to setup my 3660 router. I can ping the LAN side (192.168.1.1) with no problem, the DHCP functions as it should. I can see activity on the on the WAN port indicator but no internet access. I have attached .doc file that shows the "sho run" info. My network will be setup as follows Charter Cable Motorola Surf Modem - ethernet to MM fiber converter - MM fiber over to Sun Microsystems cabinet fiber closet - MM fiber card (on Cisco 3660 router FA6/0 WAN interface) - LAN interface FA0/0 - Cisco 3524 managed switch. One of the gigabit MM fiber ports on the Cisco 3524 feeds a 3Com Superstack 12 port gigabit fiber managed switch. My two Dell 2950 servers will be on the Superstack gigabit fiber backbone. The Cisco 3524 10/100 ports will have a Cisco access point, two IP addressible battery backup units, two Dell Desktops, and a LG Blu Ray player.
How filter inbound routes in Cisco ASA OSPF? Because Cisco ASA has no "distibute-list" command for OSFP process configuration, I try to use "filter-list" command in area definition. So, I try to use next configuration:
I am using cisco c3660 to act as Terminal Server for the communication of production machines in my company, recently there is a communication lost issue happen and its due to physical cable unplug from the machine. to troubleshoot for this issues i have to physically go inside my production area to check on it, as i understand from vendor we can check on the physical machine to see whether the LED light on the module is green or not, but in case of need to troubleshoot at night time, its time consuming as i need to travel back to company. is there any command that i can issue in the router c3660 to check on the physical connection between c3660 router and the production machine? the IOS version is IOS (tm) 3600 Software (C3660-I-M), Version 12.1(4)
i have an ARRIS TM822 cable modem provided by comcast, in addition i have a linksys e3000 wireless router. what i am trying to accomplish is to bridge the cable modem over to the router. i messaged comcast about this issue and i have attempted what they told me to do, but im not getting any where.
I just picked up a 24 port Catalyst 2950 to expand my home network and learn a bit more about networking. Having just upgraded the IOS software 'm now trying to get this to work as required on my network but I'm having a few issues.
My intentions are to plug my cable router/modem wan connection which is set up as the dhcp server to fa 0/1, then use fa 0/2 - 24 for the rest of my wired network. So essentially all on the same subnet interfacing with the router 192.168.0.1.
So far I have set up all of the security on the switch, and have all switch ports assigned to vlan1 with no IPs. My laptop connected to fa0/2 however is not assigned an ip address. Looking at a few posts I ahve rightly or wrongly played about with dhcp snooping.
Config Current configuration : 2205 bytes ! version 12.1 no service pad service timestamps debug uptime service timestamps log uptime service (code)
Recently I connected a Linksys wrt54g broadband router so that my daughter could also be online. the problem i have developed is that while I have the router connected to my network, my internet keeps kicking me off. When I disconnect the router my internet stays on and I have no problems with it. I am working with a custom built PC with quad core processor, 4 gigs of RAM, nvidia graphics card
I work from home and host quite a few machines within my home network which are all accessible internally, however I have a requirement to be able to access multiple services externally.I have standard home broadband with a SKY ADSL Router Modem and have the ability to set a DMZ, however i can only put 1 IP address as the DMZ destination. This means that from externaly, I can only access a single machine, obviously I can RDP from there but I need other services, for example SSH to another machine. Anything that I can buy which I can set as my DMZ, but can have rules which will redirect me once in the internal network to different services?
I am wanting to take my cable internet connect and give it to the other to networks and be able to communicate between the two networks. I believe this can be accomplished by IP routing, but have no clue on how to do it. What I would need to input into the 3660 to make it work? Right now the 3660 has the factory default setup, I haven't configured anything on that yet.
I'm currently in the process of buying the new property, which is in the build process and would like to put some cables across 3 floors, which would be connected to the router downstairs.
I have been using a Cisco 877 to connect to BT broadband and it was working fantastically with no issues. For reasons outwith my control we have moved to 02 and I cannot get the cisco router to connect (the supplied router works fine). O2 support is limited as they say they will not assist in the config of third party routers but they have supplied the below (the line has a static IP). I have also included my current config which was working fine with BT. I have attempted to write in the updated info but have been unable to get the line to connect. [code]
I am using a Linksys Wireless-G Broadband Router(Model WRT54G). I am trying to set up a desktop computer to have a wireless usb adapter running so I can connect to the Wireless-G Broadband Router. When I run the setup CD for the wireless usb adapter it asks me to push the Wi-Fi Protected Setup Button on the Linksys Wireless-G Broadband Router.
I have looked at the Linksys router found an obscure button on the front with the Cisco Systems Copyright logo on it. I pushed this but the wireless usb adapter failed to locate the wireless network. There is also another button on the back of the Linksys Router that is a Reset button.
I thought I saw a post/question in regards to "how to" configure a Broadband backup for a MPLS circuit.. What I am trying to do is use a cable/dsl/ broadband (secondary) connection as a backup to a MPLS circuit (primary). I have EIGRP and BGP configured on both the branch endpoint and the tunnel headend. The tunnel is used by the interface that connects to the secondary circuit. The branch location router is a 1841 and the "headend" tunnel router is a 3825. I am wondering about the configuration/syntax of a "weight" or static route that can be used to have data flow over the tunnel when the MPLS circuit goes down - and then switch back to the MPLS circuit when it comes back on line.
I want to connect my home phone to the pc and make aqlls through voip. I do not want to use the headphone as it is not good to be used in the office.Or if I have a modem, can that be converted to make voip calls on a pc?
our windows PC's will connect to the home (wireless) network briefly (~15 sec) and then lose the internet connection. The wireless connection seems to stay strong. During that period any browser activity will result in a DNS error message and the Win7 network signal shows strong but not connected to the internet. We tried setting static IP addresses on the PCs but no luck. A number of PC's all running Win7 exhibit this issue.After 5-10 min it reconnects and everything is normal.Network is a 20 mbs cable based system.
I have just moved into a new home and there appear to be ethernet lines running to several rooms, all converging in a wiring box. However, I can't figure out how to make this thing work properly.
The blue cables I'm holding in this picture apparently run to the other rooms of the house. The yellow cable goes to my WRT54G router. A cable modem is plugged into the router. Wireless networking is functioning properly.
If I plug my laptop directly into this box, and disable wireless networking, I can reach the router from the laptop, and the light for the yellow cable going into the router turns on. However, if I plug any of the blue cables into any of the ports on this box, the laptop loses connectivity and the link light on the router turns off, as though the router were not plugged into the box at all.
The cables are cat 3e. There is an alarm system, but it is not active, and I don't think it's actually connected to the box at all. The top-left port is marked "RJ31X Line Intercept", and there is a jumper that can be plugged in there, but it doesn't seem to matter whether it is or is not plugged in.
I's studying for my Network+ exam, and I somewhat confused when reading up on internet protocol. Is PPP only used for Dial Up connections, or also with Broadband? And what type of encryption if any does it use?
I have a general networking question regarding VLANS, multiple broadband connections and accessing PC's on both setups from each other.What I would like to do is have 2 broadband connections, one a cable connection and one a DSL connection. I would like to run them both through a Netgear FS-726T switch. Since the cable connection will go through a Linksys router giving out I.P.s in the range of 192.168.1.x and the DSL will probably use the same range, I would like to keep specific PC's connecting through the DSL connection and some other PC's specifically through the cable connection. I THINK that this can be done via the use of VLAN's set up on the Netgear switch but I am unfamiliar with setting them up. I've read through the manual and researched it online but I must be missing something. Just can't seem to figure it out so it's time to ask the experts. Due to the bandwidth limitations on the Comcast connection, I would like to avoid any data coming from the PC's on the DSL connection from going out through the cable connection (I do customer support for my business and want customers to be able to access files on my file server and also be able to back up their PC's online to my backup server but on the DSL connection. I will eat up my cable bandwidth in a hurry just from the backups alone. I would like to set up all the PC's with static I.P. addresses if possible. Now, I also need to be able to remotely access any of the PC's from outside my network (which I can do now) but I need to be able to access the cable connected PC's from the DSL connected PC's and vice versa.
I need to use the company laptop to connect to home broadband. However, when it is connected, it shows "no or limited connectivity".All the other laptops/computer at home can connect without any problem.When I try to use my iPhone as hotspot. My company laptop can connect and browse websites (but extremely slow because is 3g speed).
I am trying to figure out how I can see what my monthly total bandwidth usage is. I have been trying to find a way to monitor my internet usage so I can make an informed decision on ISPs. one has a cap but allows ESPN3, the other is the opposite on both accounts. everything I have been finding look like good products however they all look like they are for an individual device. I have about ten devices and not all would have the ability to have these programs on them. I have and old xp machine that really is only good as a paper weight, If I had to I could make it a proxy but before I do that and create a major bottleneck I wanted to see if there were any other options
i have triple storey house. in all three floors a broadband connection point (rj45 jack) is there. i have connected one wireless router in 3rd floor. but the signals are not coming on second floor. can i connect netgear wireless access point with one ethernet point in the 2nd floor broadband connection jack (Rj 45), to access wirelessly my internet?
Currently I am hosting a 7 day mountain retreat, for about 90+ people. Clearly they are dependent on the internet teet as am I I am trying very hard to provide internet to our friends, but I just can't seem to figure it out I have a Mobile Broadband Router (MBBR) which limits connected devices to 6, so I figured that if connect a home router with wifi (WIFI) that allows 253 connections problem solved right? So I put a short LAN cable from the LAN port on the MBBR to the WAN port on the WIFI and presto! The WIFI gets a IP address, but does not allow other users of the WIFI to get internet. I've even killed all security on the WIFI and put the WIFIs IP in the DMZ on the MBBR. I noticed the DNS was the same as the gateway on the WIFI, so I changed that to the DNS on the MBBR still nothing.
PS Yes I have a connection on the MBBR I am on it now.Connecting the LAN cable from the MBBRs LAN to the WIFIs LAN extends the range, and grants internet to the WIFI users... but uses the MBBRs DHCP to give IP addresses, which limits to 6.I guess the goal here is bypass the limitation of the MBBR by using the WIFIs DHCP to issue IPs?
I have a god-knows-which brand broadband router through which I access the net. This router has 4 ethernet ports. I have 2 laptops (with wifi obviously) & a desktop connected to the router by the standard LAN cable. I was wondering if I could network all the three through the router
Guys I want to connect most of my home to a single router located in basement.I got the router from ISP and hooked it with one of those devices that transmit Ethernet via electricity and in the ground floor I hooked WRT54g to the other device (electricity transmitter) and configured WRT with the following:Disabled DHCP so it will be done by the router.
On the first floor I hooked the WAP54g and configured it as wireless bridge with the same as above and entered the MAC address of WRT device. The only difference is the channel is 6.In ground floor the signal is great but on first is not because it doesn't get an IP and even if it gets one it losses is soon. So I turned WAP device and I got stale connection but very poor.
I have two LANs in my house, one 10/100 base and the other 10/100/1000, but one internet connection that I would like to have access to on both networks. Right now I have two Belkin routers for each network. In addition I have a Cisco 2600 and 3660. I know they are old, but they seem to be in operational order. Can I use those to combine to two networks? The only thing I want to maintain is the speed on the gig network, from the router to the PC's and devices.
I think I might have a problem with how my network is set up.
Cable Modem --->ASA5505--->Cisco 3660--->Switch For some reason if I use the ASA as a DHCP server too, the internet is much faster. Could the 3660 be slowing down the netwok? The 3660 has 2 FE ports, so it should be running good at 10/100 correct? Is there another setup I should consider to speed up the network? [code]
Remove PPPoe settings on Vista. I uninstalled the att software but the pppoe settings remain and my computer says my network is unidentified and will only allow local connection. My XP computer had no problem making the change but the Vista one keeps saying it is an unidentified network. I have tried turning everything off and then restarting the cable and then the computer but it does not work. I have a wireless adapter and can connect the Vista machine to the network with no problem but need a wired connection for games I play so I need to fix the wired problem. I am sure the settings the ATT software changed is the problem but I don't know how to get into the system to fix the problem. There is no router involved. The router is built into the cable modem.
I am having a tough time connecting these two routers wirelessly, i had connected a WRT54G Linksys software to the WRT54G DD-WRT router with no effort. But these two will just not connect.
I am having a problem with my cisco 3660 router. I have installed a wic 2T interface card and every time i set it to "no shutdown" the interface always went down and keep getting the following message " %FECPM-2-SCCFAIL: Init of SCC2 for int 0/0 failed to do fecpm_dma_init" .
I am using 3660 Router, all cards are working fine as expected but NM-2FE2W is booted & then down. Following error is occurred in show diag "Port adapter is disabled deactivated".I have reset the card as well as router, changed the slot of card, but the problem is not resolved.
It's about a Linksys WRT54G with Firmware: DD-WRT v23 SP2 (09/15/06) std it started resetting it's admin panel settings once every few months, lately it does that every few days, like name of LAN network, name encryption and password of the wireless AP, IP filter setting and so on
I am facing low relaiblity issue in one of the ethernet port even no link is connected to that port.
Router model : cisco 3660 IOS - c3660-ik8s-mz.122-24a.bin Ethernet1/2 is up, line protocol is down Hardware is AmdP2, address is 0007.85fb.c312 (bia 0007.85fb.c312) MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, [Code]...
