I am wanting to take my cable internet connect and give it to the other to networks and be able to communicate between the two networks. I believe this can be accomplished by IP routing, but have no clue on how to do it. What I would need to input into the 3660 to make it work? Right now the 3660 has the factory default setup, I haven't configured anything on that yet.
View 3 RepliesHow filter inbound routes in Cisco ASA OSPF? Because Cisco ASA has no "distibute-list" command for OSFP process configuration, I try to use "filter-list" command in area definition. So, I try to use next configuration:
R1 (Cisco 3660):
skip
!
router ospf 1
[Code].....
I have a good working knowledge of TCP/IP networking. I have a Cisco 3660 router I'm wanting to use in place of a WRT54G router with my Charter cable internet service. I saw a youtube video where a guy demonstrated how to use a Cisco 2600 series router with home broadband service. I followed the video to setup my 3660 router. I can ping the LAN side (192.168.1.1) with no problem, the DHCP functions as it should. I can see activity on the on the WAN port indicator but no internet access. I have attached .doc file that shows the "sho run" info. My network will be setup as follows Charter Cable Motorola Surf Modem - ethernet to MM fiber converter - MM fiber over to Sun Microsystems cabinet fiber closet - MM fiber card (on Cisco 3660 router FA6/0 WAN interface) - LAN interface FA0/0 - Cisco 3524 managed switch. One of the gigabit MM fiber ports on the Cisco 3524 feeds a 3Com Superstack 12 port gigabit fiber managed switch. My two Dell 2950 servers will be on the Superstack gigabit fiber backbone. The Cisco 3524 10/100 ports will have a Cisco access point, two IP addressible battery backup units, two Dell Desktops, and a LG Blu Ray player.
View 21 Replies View RelatedI am using cisco c3660 to act as Terminal Server for the communication of production machines in my company, recently there is a communication lost issue happen and its due to physical cable unplug from the machine. to troubleshoot for this issues i have to physically go inside my production area to check on it, as i understand from vendor we can check on the physical machine to see whether the LED light on the module is green or not, but in case of need to troubleshoot at night time, its time consuming as i need to travel back to company. is there any command that i can issue in the router c3660 to check on the physical connection between c3660 router and the production machine? the IOS version is IOS (tm) 3600 Software (C3660-I-M), Version 12.1(4)
View 3 Replies View RelatedI have two LANs in my house, one 10/100 base and the other 10/100/1000, but one internet connection that I would like to have access to on both networks. Right now I have two Belkin routers for each network. In addition I have a Cisco 2600 and 3660. I know they are old, but they seem to be in operational order. Can I use those to combine to two networks? The only thing I want to maintain is the speed on the gig network, from the router to the PC's and devices.
View 6 Replies View RelatedI need data sheet ( technical sheet) for Cisco3660-MB-2FE router.
View 6 Replies View RelatedI think I might have a problem with how my network is set up.
Cable Modem --->ASA5505--->Cisco 3660--->Switch For some reason if I use the ASA as a DHCP server too, the internet is much faster. Could the 3660 be slowing down the netwok? The 3660 has 2 FE ports, so it should be running good at 10/100 correct? Is there another setup I should consider to speed up the network? [code]
I am having a problem with my cisco 3660 router. I have installed a wic 2T interface card and every time i set it to "no shutdown" the interface always went down and keep getting the following message " %FECPM-2-SCCFAIL: Init of SCC2 for int 0/0 failed to do fecpm_dma_init" .
View 2 Replies View RelatedI am using 3660 Router, all cards are working fine as expected but NM-2FE2W is booted & then down. Following error is occurred in show diag "Port adapter is disabled deactivated".I have reset the card as well as router, changed the slot of card, but the problem is not resolved.
View 8 Replies View RelatedI am facing low relaiblity issue in one of the ethernet port even no link is connected to that port.
Router model : cisco 3660
IOS - c3660-ik8s-mz.122-24a.bin
Ethernet1/2 is up, line protocol is down
Hardware is AmdP2, address is 0007.85fb.c312 (bia 0007.85fb.c312)
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
[Code]...
I am troubleshooting interface resets on a 3660 connected to a 3550 over Fast Ethernet. I have hard coded both sides for full duplex and 100Mbit. The 3660 is incrementing interface resetes about 4-6 times a day and the 3550 is clean. I have noticed this in other similar configurations as well.
View 4 Replies View RelatedI am position to migrate from CatOS 6509 switch to native IOS 6509 switch. long time ago, there was some site to convert automatically based on copy and paste onto the tool, but i can not find.
Does anybody know how to convert CatOS configuration to Native IOS configuration ? It is not IOS change, but it is configuration convert.
In 3750 switch,I have configured intervlan routing.I have three vlans Vlan 10,vlan 20,Vlan 30 and I have assigned IP address for that Vlan.In vlan 10,I have connected one systen gigabitethernet 0/1 interface.From my system I am able to ping vlan 10 ip address but I can't able to ping other vlan ip address (vlan 20,vlan 30).Is it possible to up the protocol for all that time.
View 2 Replies View RelatedI've one Cisco 3750G-12S with ip routing enable, the swtich is with IP Service firmware, with PRR support.Currently set my default static route 0.0.0.0 0.0.0.0 10.1.18.71 to my Firewall A Currently all of the VLAN for will be routed to 10.1.18.71
I've created a new VLAN 2 for my 10.1.2.0/24 network with the VLAN interface 2 ip address 10.1.2.10, my intention is to route 10.1.2.0/24 traffic to my 10.1.2.1 by creating the access list and route-map.
I've configure my test pc with a static ip and my gateway pointing to 10.1.2.10 (VLAN 2 gateway) , i'm not able to route to 10.1.2.1.
Why does mine show this and NOT all 4 ports and 1 wan port?
Manases#sh verCisco Internetwork Operating System SoftwareIOS (tm) C831 Software (C831-K9O3SY6-M), Version 12.3(2)XA7 [code]...
How do I make it show all my ports? when I plug in something to port 1-4 it shows me on the log that I plug in to e0. I got port1-4 and 1 wan port.
I was recently given a PIX 501 router. I am very new to the world of Cisco, but want to learn. I got a few things setup on the router but, am not sure how to get it to use my DSL connection. My DSL modem IP is 192.168.2.1. Below is my router config. What more do I need to do? Also, is the outside IP not the IP of the DSL modem?
PIX Version 6.3(1)
interface ethernet0 100full
interface ethernet1 100full
nameif ethernet0 outside security0
[Code]...
i have the asa5505. the configuration of asa 5505 is:
: Saved
Code...
i analyzed this traffic i see problem with the nat- Asymmetric NAT rules matched for forward and reverse flows. where i made error?
how to backup the configuration of ACS 5.3 then restore it on the secondary ACS 5.3 Appliance in order to save time without configure the 2nd Appliance?
View 1 Replies View Relatedi have linksys modem which already running for differents vlans i cerated another different vlans 10 amd 20 for 10 and 20 i need internet how should i configure internet on another core switch3750
View 0 Replies View RelatedI have been using a Cisco 877 to connect to BT broadband and it was working fantastically with no issues. For reasons outwith my control we have moved to 02 and I cannot get the cisco router to connect (the supplied router works fine). O2 support is limited as they say they will not assist in the config of third party routers but they have supplied the below (the line has a static IP). I have also included my current config which was working fine with BT. I have attempted to write in the updated info but have been unable to get the line to connect. [code]
View 6 Replies View Relatedi have a router 2921 with the aproprieted voice card for E1 and licenses. I would like to know how to configure it for incoming and outgoing calls. I already configured the ephone and SIP phones for internal calls. now i just need to configure it for send and receive external calls.
Router:
IOS: c2900-universalk9-mz.SPA.153-1.T
CME: 9.1
ISP from Brazil:
type: E1
signal: R2 Digital
Channels: 32
Phone Number Iniital: XXXX-9250 (main)
ephones-dn numbers: 9250 to 9280
I have a network behind an 861 and users are unable to access e-mail from the local exchange server from their iPads using the 802.11wireless network. The wilrelss network is working fine and the iPad users connect fine.I was told that that i need to configure "hairpin DNS".
View 2 Replies View RelatedAny configuration example to build a vpc b/w 5ks and 7ks? i have total 4 links between them . If not, I am assuming to have the following config for the port-channels:- (Provided the vpc domain is configured).
N5k1 and 2:
int eth1/10-11
channel-group 10 mode active
switchport mode trunk
int po10
switchport mode trunk
switchport trunk allowed vlan a-d
[code]....
So, its basically vpc 10 that has 4 physical links b/w the vpc domain of 7ks and vpc domain of 5ks.
I'm currently trying to get up to speed on a 1941W ISR. I belive i have most of the configuration correct based on reading the documents on this site. However, i'm noticing that my lan to lan network performance is very slow. Peaking out about 3mbs. I was reading some documentation that suggested MGF (MultiGigabit Fabric) might resolve this problem.
I have a basic setup in my test environment trying to emulate a branch deployment. 1941W connected to a access switch (3400).
- I'm getting slow perfomance (thoughput) between the vlans 66,30,10. Will MGF fix this problem? How do i configure it?
Building configuration...
Current configuration : 7474 bytes
!
! Last configuration change at 09:26:04 PCTime Fri Dec 28 2012 by xxx
! NVRAM config last updated at 09:26:05 PCTime Fri Dec 28 2012 by xxx
[Code]......
We recently switched a faulty N5548UP with a replacement and everything went fine, with the exception of one minor thing.
We're currently unable to authenticate using tacacs+.
When trying to enter the command 'aaa authentication login default group [groupname]', the following msg appears: too big pss key or value size could not update aaa configuration
We're running 5.0(3)N2(2b).
I currently work in the IT field part-time as a end-user support technician while I am finishing my Bachelor's Degree in Network Administration. I'm not completely new to networking at this point, but I am by no means a master of it either. The basics of small networks (less than 10 PCs) and the lower-end of small business grade Cisco equipment are not unfamiliar to me. Up until this point however, I have had very little experience with any higher-end Cisco networking equipment.
Now on to the questions, which may seem like the answers should be obvious, but let's face it, I do not have the resources to own much equipment myself at this time for experimentation purposes, nor does the school I am attending have a lot of financial resources to provide us with recent hardware to learn on. What I want to know are a few things about PoE as implemented on Cisco devices, specifically the SG200-50P small business series switch. According to the technical documentation, the switch supports PoE on 24 of its 48 ports, specifically 1 - 12 and 24 - 36; simple enough. The switch is currently installed in an office that has less than 24 connected devices, but that is currently expanding. None of the PoE ports are utilized as of yet, but going forward, there will be more than 24 connected devices. Will another switch need to be installed if the additional connected devices (PCs and printers) are not using PoE, or is the PoE an auto-sensing feature that will simply remain disabled if a device that does not require power over the network cable is connected? Is there some setting that needs to be changed through the management interface to keep devices that should not be drawing power from doing so?
There will likely be some additional questions generated by my inquiry, and I fully understand if these are completely novice questions, but I admittedly do not know the answer. When I Googled it, I was greeted by a few hundred thousand results, the first dozen or so pages of results all being for places to purchase this particular type of switch, so I thought I would try my luck on the forums of the place that made it.
On a recommendation from a network engineer, I got a used Cisco 891. Having worked with small business routers most of my working life, I thought this should not be a problem. However, I had no clue these things used a console and command line to initialize. I have the console cable, am able to console into the device, but am haphazardly issuing command lines straight out of the PDF manual but cannot get Cisco CP to discover the device.
From what I can tell, I am stuck at the point where the manual tells me to enable http server. I ran the command lines several times, executed write mem where available, but when I run the show services command, http is not enabled.
And if you do refere to command lines, I was reading some other forums and they were speaking of "run this command, run that command" but I could not make out the correct syntax, in what mode, whether it be config or config t, etc. So I might need a wee bit of handholding.
I'm hoping that once I can get Cisco CP or CPE to discover the device, I can make my way through the GUI to configure since those usually do make sense to me. As of now, I'm in the thick of it ...
I am trying to configure a 891 W to basically provide DNS from my ISP to my internal clients on the 891 W. Currently when I am on a PC I can see that I receive my IP information along with the correct ISP DNS IPs. However when I try to connect or resolve a URL it fails. Nor can I perform an ns lookup from the cli of the 891 W. I seem to be having a translation issue with DNS.
View 2 Replies View RelatedI am trying to configure Cisco SG300-52 switch for the first time and stuck without CLI configuration option. The configuration can be done using GUI, however, configuring using CLI would be more comfortable (as I am used to work with CLI of other Cisco switches)..
I was able to lo gin to switch using SSH, but the CLI appears in MENU format and was not able to find any way to go to CLI mode.
As per some blogs, in SG300 switches CLI mode can be accessed using Ctrl + Z in Menu, which did not work either in my case.
Switch is running with latest firmware version Sx300 Firmware Version 1.2.7.76.
I have a headquarters office that has recently bought a new voice system.
We have a site to site connection from the head office to 3 remote offices. All have ASA5505 firewall.
I have created 2 interface on the ASA5505: 1: inside with vlan1 and switch port port12: voice with vlan100 and switch port port2
Port1 on the asa goes to port 23 on the switch for vlan data
Port2 on the asa goes to port 24 on the switch for vlan voice
Port23 is member of vlan1 data
I added vlan100 to port 24 but by default vlan1 is member and i can't remove it. Its greyed out
All ports on the switch are member of vlan1 and vlan 100 because the port on the switch goes to the phone and from the phone there is a port that goes to the PC. Phones are getting addresses, and PC as well.
I am having a kind of loop because there is 2 exit for vlan1 (port 23 and 24) and that's slowing down my system and sometime i loose the connectivity to my servers.
When i do a show arp on my asa, i do see that some IP are beeing learned on the wrong interface. some PC addresses 192... are on the voice and some voice IP 10.10... are on the inside.
I am pretty sure that the problem comes from my switch configuration.
I've goggled and searched here, and I can't seem to find what I'm looking for. I need to make a couple changes to a clients Cisco 800 series router, enable ping replies add ip addresses to the ssh ACL.I can't seem to find any basic commands for CLI anywhere.
View 2 Replies View RelatedI have a Cisco 850 router that whas having problems getting an ip address via DHCP. I did some stuff on it but that didn't work, so I rebooted the router to go back to my last saved startup config. When I turned it back on and connected t othe CLI console I got the "Would you like to enter the initial configuration dialogue?" message. Thinikng I just forgot to save anything to the startup config I went through the initial set up again and made sure to save everything to the startup config. After going through the intial config and setting up a vlan to assign DHCP to clients I saved the config and rebooted, upon reboot and connecting to the CLI console I got the same "Would you like to enter the initial configuration dialogue?" message. Tryign the setup once more and making sure everything was saved to startup config I rebooted again just to make sure the changes would stick, and sure enough they didn't. Whay is the config not saving to the startup config?
View 3 Replies View RelatedI'm looking to do a basic QOS configuration which states that VOIP traffic has priority over anything else.
View 3 Replies View Related