Cisco WAN :: 7200 STM4 Port Adapter
Jul 30, 2012I'm using PA-SON-OC3 on 7200VXR (NPE-G1). I want to upgrade the link to OC12 with same wavelenght. I found PA-SRP-OC12SMI for this purpose but I'm not sure about compatiblity.
View 2 RepliesI'm using PA-SON-OC3 on 7200VXR (NPE-G1). I want to upgrade the link to OC12 with same wavelenght. I found PA-SRP-OC12SMI for this purpose but I'm not sure about compatiblity.
View 2 RepliesIs there a Port Adapter (PA) with Synchronous/Asynchronous Serial Ports, for Cisco 7200?
View 1 Replies View RelatedWe are running ISP and now a days we have many spam in our network, we want block the SMTP port 25 block on Cisco router 7200. So we can block the spam in our network.
View 3 Replies View RelatedI have been using the Cisco7613 and FlexWAN with PA-8E1-IMA PortAdapter.It has been used for ITP (SIGTRAN) Today, I attemted to enter the Port Adapter 13 1 module with using command that "attach" command.But I couldn't that. and I could see the Error Message below." RTTYC_ ATTACH_ REQ Failed with return code 2 , aborting". This Module (13 1) is working normal. but why cannot enter to the PA ?
View 3 Replies View RelatedI am using 3660 Router, all cards are working fine as expected but NM-2FE2W is booted & then down. Following error is occurred in show diag "Port adapter is disabled deactivated".I have reset the card as well as router, changed the slot of card, but the problem is not resolved.
View 8 Replies View RelatedFrom what I have found the VPN (WS-IPSEC-3) port adapter (on a WS-SSC-600) is not supported if you decide to turn the 6509-E into a VSS system.
View 2 Replies View RelatedIs there any solution for automatic switching between wired and wireless network connection?
In my work we have two option for connection to network. Wired for working but with blocked pages like youtube and other streaming media. And wireless for visitors which haven't blocked any pages but I can't do my work on it. Can I by connected to both and some utility will doing switching between them? I want to use streaming and be connected to wired network which has blocked streaming.
I use Dell vostro 3550 as wireless spot but I'm have a problem with "WiFi mini port adapter". , when i try to enable "Intel My WiFi technology" . it's enable but WiFi card die after few minute, i can't see any signal of wireless network.....and of course,
my phone not see the signal wireless by my laptop. This problem appeared two months ago, before I use it very normal. I try reinstall driver wireless, window but ---> nothing change. My card wireless: Intel(R) Centrino(R) Wireless-N 1030.
I am having a problem getting serial interfaces to show up with a NM4A/S card in a 3745 router. It worked at first but now the serial interfaces don't show up in running-config but show diag shows the card is present but says "Port adapter is disabled deactivated". I have tried the card in 3 different slots and of course turned off power when moving card around (left power cord in for grounding). Again, it was once working (serial interfaces were showing up in running-config) so if I damaged the slot somehow, however I was very careful when seating card. Have been searching the learning network and google for days now to no avail. Have tried to find something similar to the card type command thinking the port adapter needs to be activated but have not found any documentation about that. Hope card isn't bad all of a sudden but really don't think it is since it worked before and it seems to be recognized just not showing serial interfaces in running-config/sh ip int b (on ios/cli). Really think it's something along the lines of activating card, but not sure.
View 1 Replies View Relatedi have an issue for collect data on adapter 1, that don´t collect data but see that adapter 2 if collect data on module 4.
monitor session 1 source vlan 102 rx
monitor session 1 destination analysis-module 4 data-port 1
monitor session 2 source vlan 106 rx
monitor session 2 destination analysis-module 4 data-port 2
I reconfigured newly monitor and continues with that issue. Always ok by data-port 2.
- show version Cisco 6513
Cisco IOS Software, s72033_rp Software (s72033_rp-ADVENTERPRISEK9_WAN-M), Version 12.2(33)SXH7, RELEASE SOFTWARE (fc3)
. show version NAM
NAM application image version: 3.5(1b)
- sh module
Ports Card Type Model
----- -------------------------------------- ------------------
8 Network Analysis Module WS-SVC-NAM-2
Hw Fw Sw Status
------ ------------ ------------ -------
2.0 7.2(1) 3.5(1b) Ok
Just purchased an Asus K532-BBR9 laptop. Everything works fine, except on college campus the internet is very slow, and disconnects every few minutes.My fellow students laptops do not seem to have this problem.I figured it may be a driver issue, so I am trying to update everything.Under Network Adapters in Device Manager. The Microsoft Virtual WiFI Miniport Adapter is not up to date when I do a driver update scan.Then it says "Windows can't verify the publisher of this driver software.." with options to install anyways.
View 2 Replies View RelatedOn the WAN port, there are 4 pins that are traced to the internal serial traces. Where can we get the cable that will fit into the WAN RJ-45 port and have a serial connector on the back end. It may be called a Cisco Debug Adapter, but we haven't been able to find?
View 9 Replies View RelatedI want to use chanelized POS PA in 7200 router. I want to know can I use chanelized PA for both chanelized and non-chanelized OC3/STM1? Does the both chanelized and non-chanelized feature is supported on chanelized module or I have to use other module?
View 1 Replies View RelatedI ran across this today on a 7200 that when all the vty lines are filled, and dont release, you enter clear line vty x and it is supposed to release the line. Well in some versions it doesn't work.
Here is the work around I found. clear tcp line vty x
I want to monitor my 7200's CPU packets per second rate.Any command i can run to show this?Or any MIB so I can poll this? 7200 NPE-G1 can handle 1mpps. And i want to verify the actual rate.
View 1 Replies View RelatedI want to know a number of maximum tcp connection at same time on interface of my 7200 router, how I'll do that?
View 3 Replies View RelatedI am having issues with frequent bgp flaps on the Cisco 7200 series router from past 1 week. I have raised a ticket with ISP but couldn't get any resolution from them as the flap is for about 2min.When ever we see BGP flap, we are not able to ping the remote end IP, Also at that point we drops on the interface connected to ISP.
View 1 Replies View RelatedI was recently given a Cisco 7200 VXR and told to erase the stored configurations in it. how to do erasing of Cisco 7200 stored config else I might have to delete them line by line.
View 4 Replies View RelatedWe have network consisting of approx. 8 7200's running LNS/MPLS/BGP and we provide predominantly private networks to clients(Majority of client networks are a mix of Ethernet tails and DSL).We have received a request from one client to support multicast - Having never implemented multicast, have a few questions:
1. Is is supported/possible to provide multicast within a vrf on 7200's?(From initial investigations, it appears to be)
2. Is it possible to only enable mutilcast in a vrf(i.e. not globally)?
3. Any recommended guides/best pratices?(Googling has revealed nothing really that is similiar to what we want to do)4. What are the potential ramifications?(Resource overhead, Security implications, anything else?)
I am planning to provide a redudnt link to our customer. The setup as below:
One link over wireless while the other link over wired link, I want to make sure that I should maintain the same public IP addresses for the customer therefore, I am looking for L2 failover for my customer.
If the wireless down the customer should migrated to wired and vis versa. I have 7200 CISCO Router as Core.
I am trying to configure a dynamic failover with IP SLA on a Cisco 7200 using 12.2(33) IOS. I would like to have something similar as the following configuration:
ip sla monitor 1type echo protocol ipIcmpEcho x.x.x.xfrequency 3ip sla monitor schedule 1 life forever start-time now!!track 10 rtr 1 reachability
access-list 101 permit icmp any host X.X.X.X echo!route-map LOCAL_POL permit 10 match ip address 101 set ip next-hop Y.Y.Y.Y set interface Null0!ip local policy route-map LOCAL_POL
!
ip route XX.XX.XX.XX 255.255.255.0 YY.YY.YY.YY track 10ip route XX.XX.XX.XX 255.255.255.0 ZZ..ZZ.ZZ.ZZ 254
My questions are the following
Question 1: What is the equivalent of ip sla monitor in 12.3 for dynamic failover with IPsla Should I used
ip sla ethernet-monitor 1 type echo domain name ?
or
ip sla 1 path echo X.X.X.X or ethernet mpid echo domain name or icmp-echo time out 1000 frequency 3 threhsold 2
I do not know if I have to used ethernet-monitor or ip sla. What is the domain name and the mpid associated to the ethernet-monitor ip sla.In the case where I have to used ip sla 1, shoud I used a path-echo, ethernet mpdi or icmp-echo for dynamic failover
Question 2: In 12.3, what is the equivalent to ip sla monitor schedule 1 life forever start-time now.I have found thec command ip sla schedule 1 start now but it does not seems that we could configure the duration.
Question 3: Should I also enable ip sla responder
I have a 7200 router with a 12.2.(46a) IOS and I am trying to activate Netflow on a subinterface. From the documentation of Cisco, I should be able to do it since the ios 12.2.(14)S but the command is unavailable.
[URL]
I have tried also to enter the command in the subinterface directly but it doesn't recognize it.
We have a Cisco 7204 G1 running c7200-advipservicesk9-mz.122-33.SRE7.bin and we're having a lot of difficulties getting a VTI working to a Cisco 2921 with adv. security. I've ruled out that the 2921 is at fault by successfully establishing a VTI to another 2921 and a 7200 running a different IOS release.
We see the tunnel come up, but when I sent a ping from the 2921 to the 7204 there isn't a reply. When I look at the results on the 7204 from a 'sh crypto engine connection active', I see the decrypt counters increase, but I don't see the Encrypt counters increase as it's trying to reply to the ping. I'm not sure if this is because there is an issue with the encryption or whether there might be a more fundamental issue with the router not replying to the pings.
I've tried the following IOS releases (c7200-advipservicesk9-mz.122-33.SRE7 & c7200-advipservicesk9-mz.122-33.SRE6) and they all behave the same way - this makes me think it might be a config issue rather than and IOS bug which is what I first thought. c7200-advipservicesk9-mz.122-33.SRE7.bin.
sh crypto engine connections active
Crypto Engine Connections
ID Interface Type Algorithm Encrypt Decrypt IP Address
1 Tu10 IPsec 3DES+SHA 0 31 10.5.5.1
2 Tu10 IPsec 3DES+SHA 19 0 10.5.5.1
1001 Tu10 IKE SHA+3DES 0 0 10.5.5.1
Here is a copy of my config on the 7204 - the other end (Cisco 2921) is configured in the same way.
crypto isakmp policy 1
encr 3des
authentication pre-share
[code].....
I have two 7204VXR with NPE-G2 and 1Gb of ram. One router has 2 eBGP peers and the other has 3. The routers receive all internet routes from the 5 peers and send 2 internal routes. There is an iBGP peering between both routers. On all peers I have a route-map to send only our routes.
All was working fine since a couple of months when I suddenly saw an increase of memory on one of the router (router B), 1 hour later the memory was 100% and router crash and reboot. The other router (router A) with the same hardware capacity, same ram and same amount of routes was working good. After router B restart, I shut all eBGP peering on it, keeping only iBGP with router A, ram used was the same as router A (about 50% used) but CPU was about 30% used by process Router BGP whereas router A which has active traffic and active eBGP is only 20% and bgp process i almost 0%. Restarting peers one by one on router B cause the same issue, increase of memory then crash, even with only one peer.
What I suspected :
- A peer on router B but I can't isolate one because the problem appears with each taken one by one
- Not enough memory, but router A has the same number of routes and don't have any problem
- IOS version ? same on both 12.4.(15)T1
- Why process router BGP use 30% on router B when all eBGP peers are shut except iBGP and no traffic pass.
- A routing loop but I only send internal routes to peers and only have one iBGP session with no sync nor redistribution with an IGP
Of course I can't run any debu ip bgp on routers as the number of routes is very large (300K).
OSPF-4-ERRRCV: Received invalid packet: Bad LLS Checksum with one of our tunnels
View 1 Replies View RelatedMy router is running with BGP (One eBGP and One IBGP session). I have filterdown the BGP roting table by using prefix-List and default route to upstream router.But still found the CPU process is high (80%/80% with 60MB traffic).
Sh Proc CPU
-------------------
CPU utilization for five seconds: 88%/88%; one minute: 87%; five minutes: 87%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
[Code].....
I am having a weird issue with my Cisco 7200 router. From the router i am able to ping and reach out to the internet but from the client i am able to reach out to the internet but unable to ping I am not sure where is the issue but when i traceroute to it my packets are dropped at my routers interface. All my pings from the client time out. I checked the Access list to make sure ICMP is not blocked. Following is my running conf
ip audit notify log
ip audit po max-events 100
ip ssh break-string ~
ipv6 unicast-routing
no ftp-server write-enable
[code]....
My company has a spare 7200 VXR, originally planned to be placed on our TDM network. This plan was not followed through, but I'd like to switch it's function to work as a core router on our BGP network. I'd like for this 7200 to be able to handle full routes from our eBGP peer, something the SUP module in my 6500 isn't capable of doing. What kind of SUP module should i look at replacing this 7200 VXR with?
View 5 Replies View RelatedPrimary optical link between CPE and PE, and backup 3G/ADSL link between CPE and PE.I am considering link failure detection on primary link (after which backup link should take over). Which method is the least CPU intesive:
1) BGP protocol between CPE and PE
2) RIP protocol between CPE and PE
3) BFD on static routes on PE
Is there difference in terms of CPU load between above mentioned methods or they are more or less the same?Hardver platforms are sup720 BXL and Cisco 7200 G2.
how many GRE tunnels (without IPSEC) can 7206 router supported. I have low bandwidth 2000 links & i want to configure GRE tunnels for them.
View 1 Replies View RelatedI have set a tunnel between Cisco pix 6.3 and Cisco Router 7200. Show Isakmp sa showing below detail on Pix
Total : 1
Embryonic : 0
dst src state pending created
xx6.x71.x29.x68 x2.1x7.52.1x1 QM_IDLE 0 0
Is tunnel is UP ? Traffice is not going throgh the tunnel . why ?
what does VXR and S means in these series?
View 1 Replies View RelatedIn my Lab environment in GNS I have connected two 7200 series router through fastethernet on router A I have given IP adress 192.168.10.54 and router B I have given IP address 192.168.10.53 and default route as 0.0.0.0 0.0.0.0 192.168.10.53 and when I run the command on router A it shows result as follows "C 192.168.10.52/24 is directly connected ,Fast ethernet 2/0".
So I need to know why it's showing the result of .52 at last why not .53 or .54 at last what is the reason it's showing .52 which I have not mentioned in my IP address.