8636 Has Only One Box To Enter Port Number Under Each Heading?
Feb 15, 2013
I changed my router from Belkin F5D 7633-4 (G) to Belkin F5D 8636-4 v2 (N) on the 7633 I was able to set up virtual server page and access my CCTV cameras remotely with no problem but on the 8636 with the same info into virtual servers page I get "No 1 WAN address is invalid".The format of the page is slightly different the 7633 required "inbound Port" number to be put in twice in different boxes side by side and the same with "Private Port".The 8636 has only one box to enter the port number under each heading.
View 3 Replies
ADVERTISEMENT
Mar 22, 2012
I have a Cisco 2811 with an additional HWIC-4ESW card. [code] I need to NAT anything heading out of the WAN port. [code] I can ping anything connected to my other private networks from my 10.0.24.0 network but nothing on the Internet. [code]
View 3 Replies
View Related
Feb 13, 2011
I have been using the Cisco7613 and FlexWAN with PA-8E1-IMA PortAdapter.It has been used for ITP (SIGTRAN) Today, I attemted to enter the Port Adapter 13 1 module with using command that "attach" command.But I couldn't that. and I could see the Error Message below." RTTYC_ ATTACH_ REQ Failed with return code 2 , aborting". This Module (13 1) is working normal. but why cannot enter to the PA ?
View 3 Replies
View Related
Mar 26, 2013
N-Wireless modem Router F5D-8636 will not let me change the lease time from half an hour?
View 1 Replies
View Related
May 28, 2012
How to know port number of any URL, for example what is port number used by google.
View 19 Replies
View Related
Apr 13, 2011
what port number does ping use?
View 3 Replies
View Related
May 31, 2012
I have a ACS 5.1, My mailing server does not run on standard port number of smtp (25). Need to know if i can customize the port number suiting my mailing server requirement.
View 0 Replies
View Related
Dec 23, 2012
I would like to understand how public IP works in remote access. I do have belkin router and when I access it remote I type my public IP and after it the port number for example xxx.xxx.xxx.xxx:80 and if I would like to access an IP cam remotely in the same network i would do the same thing xxx.xxx.xxx.xxx:5656 (public IP). I do know my Public IP is unique.Thus, its quite logical I can access my devices remotely. my understanding of the port number is application specific that addresses packets in different applications in the same computer. For example port 80 is for HTTP connection used browsing the web, for chatting in MSN i will use different port number specifically for MSN...etc. my question is how I can access my belkin router remotely by typing the public IP and the port number knowing that the port number is application specific not device specific? My second question is, is it possible to access two routers in the same network remotely?
View 7 Replies
View Related
Apr 19, 2012
End user has APs config with Radius server, working fine
-server 10.42.1.21 auth-port 1645 acct-port 1646
-server 10.36.1.46 auth-port 1645 acct-port 1646
In some weeks all APs will be migrated to WLC. My doubt is regarding the config in RADIUS Athentication Server port number field. There is only one option for adding.Which port number should I use? , When a new server is added always show 1812 port number; documentation states that is for authentication and 1813 for accounting.
View 8 Replies
View Related
Mar 19, 2011
Is is possible to set the port number for syslog eg 192.168.75.50:20514 ? i presume the protocol would stay udp
View 3 Replies
View Related
Oct 30, 2012
We have IP device on the farm switch(cat6500, which is an access layer siwtch), with the gateway on the core switches (Nexus7000), on the core when I do show ip arp, I found the mac.But when I do sh mac add add of that mac there is no port attached to that mac.
Since that particular vlan only resides on the cat 6500 and two cores, so I logged in to the 6500, and when I show mac- in that vlan, I didn’t find that mac addresss. Instead, I found another mac address with last 8bit are the same of that mac.
Is it some kind VIP of the mac? How so, if no port, how can the switch forward the frame? [code]
View 1 Replies
View Related
Nov 26, 2011
With basic "Wizard" setup I got DHCP and port 80 for the camera. It was working just fine with MyDLink and locally with DLink-ViewCam software and some local test web pages. However, we have a wireless printer on that router which also uses port 80, so when it was installed we set up a "port forward" for port 80 traffic to it for administration from other subnets. How MyDLink website is able to tunnel through our hardware firewall and the wireless routers firewall to communicate with the camera is not clear to me (perhaps someone can send me a link to an explanation??), but it works...Thus, to allow access to the camera from other subents, I wanted to change the camera's port from 80 to another, say 8181 and set up the appropriate "port forwarding for TCP and UDP. All of the steps below were from a PC within the camera's subnet/router so port forwarding is not an issue
View 5 Replies
View Related
May 12, 2012
I have configured the following access-list on routers fa0 interface (i am using 1801)
access-list 111 permit ip any any log
and applied it in "in" direction on Fa0 interface.
Now when i am sending ssh packets to this interface its showing below
*May 14 05:09:00.104: %SEC-6-IPACCESSLOGP: list 111 permitted tcp 172.18.128.2(0) -> 172.18.128.146(0), 1 packet
why its not showing any port number ?
View 1 Replies
View Related
Apr 22, 2013
Where can you set the port numbers for auth and accounting on a WAP321?I can see where to set up to four IP addresses for the servers themselves, shared secret etc - but nowhere can I see where the port number is configured.
In a day and age of exceptionally limited IP resources, cloud hosted services and even just a little "security through obscurity" there are many reasons for needing to set a non-standard port number for the radius server.I'm at a loss how it could be in residential products, but not small business devices?
View 1 Replies
View Related
Apr 19, 2012
Background: currently have a WRT320N, thinking of upgrading to an EA4500 assuming ONE feature has been improved: Port Forwarding.
Scenario: Currently I have a WRT320N router, and while it "does everything we need" it has one limitation that is now getting in the way: limitation on number of forwardable ports. In the port forwarding panel, it has 15 total rows: the first five rows can be enabled for specificaly named services (SMTP, FTP, etc). The last 10 rows are fully customizable in that we can set the name, ports and protocol.
The problem is that of the 13 total ports I currently need to forward, only ONE of them is listed in that fixed list. So, sadly, I can only use one of those first five rows. I've now filled the remaining ten custom rows, and still have need for two additional ports (for now, may need more down the road).
Trying to get creative, I figured maybe I could just spill over to the Port Range Forwarding page and add a row or two there. The only problem: it's buggy. I've found that if the Single Port Forwarding list is filled, then the Port Forwarding Range entries don't work properly. For example, if I wanted ports 12345 and 12346 forwarded to 192.168.1.5, they work fine with two single port forwarding entries. However, if I delete those, add two other port lines I need forwarded (the single list being full again), and add a port forwarding range 12345..12346, they don't work properly, ports just are closed. Only the singles work, the ranges don't.
Question: Has the EA4500 resolved this issue and allow for either more lines (i.e. 20 customizable entries instead of 10), or, better, does it just have an [Add Entry] button to allow for additional rows to be created? In today's day and age, where one single device (such as an Xbox) can take four rows, a 10-row limit is pretty sparse. Comparing it to some competitors, for example the D-Link DIR-825 (aging, but still great) allows you to add as many as you want.
I realize "expensive" firewalls like SonicWall's have virtually unlimited customization, but I don't need many of the additional features and don't want to spend $350 on a "high-end" firewall to solve the problem of needing two more ports open.
View 4 Replies
View Related
Jan 1, 2012
Clarifying whats the correct # of port asic in WS-X6704-LC?According to the following link (Catalyst 6500 Architectural white paper): [URL]
"In the WS-X6704-10GE line card, there are two port ASICs each supporting 2 x 10 Gigabit Ethernet ports"
While in the document: Understanding Quality of Service on the Catalyst 6500 Switch: [URL]
Table 10.
WS-X6704
Number of 10 GE Ports 4
- QoS on 10-Gigabit Ethernet Line Cards (WS-X6704-10GE)
So whats correct? 4 port asic or 2 port asic?
# Port ASIC’s on the linecard 4
# Physical Ports per Port ASIC 1
View 1 Replies
View Related
Apr 23, 2013
Are you only able to have two sessions for port mirroring on a Cisco 4510?
View 1 Replies
View Related
Dec 2, 2012
I'm developing a project where I use the SNMP protocol to discover the network. By discovering the network I mean go through all the routers and switches and retrieve the IP routing table from routers and the forwarding table from switches. With the routers I have no problem. For the switches I need to know for each port the MAC addresses and the Vlans. Basically it's use SNMP to find a port number from a MAC address. To do that i followed this tutorial: [URL]
The problem is that I'm using a Cisco 3725 Router with IOS 12.4 (21) and a NM-16ESW module to work as a Switch and when I use the OID .1.3.6.1.2.1.17 corresponding to the BRIDGE-MIB as it follows:
snmpwalk -v2c -c myrouter 10.1.1.5 .1.3.6.1.2.1.17
it returns:
SNMPv2-SMI::mib-2.17.1.1.0 = Hex-STRING: 00 00 00 00 00 00
SNMPv2-SMI::mib-2.17.1.2.0 = INTEGER: 0
SNMPv2-SMI::mib-2.17.1.3.0 = INTEGER: 4
From this I guess there's no information on the router about Vlans or anything. Other thing is that when I use community string indexing it returns a timeout. My theory is that this version doesn't support indexing but I don't know.
how can I get the Port Number from a MAC address from this "switch" (it's a router working as a switch) using SNMP?
View 2 Replies
View Related
Jan 3, 2012
I'm in the middle of a Nexus 5000 project and recognized today while configuring port-channels, that some of the interface numbers are reserved for internal use.
Is it possible to change or configure which port-channel interface numbers are allocated for internal use by NX-OS?
Unfortunatly I wasn't able to find a solution for this issue in the offical Nexus documentation, the search function of this forum or Google. If I did miss something or didn't look careful enough at the Nexus docs, I'm also happy with RTFM (... fine manual) responses and links to the info :-)
Additional info:
Nexus5k(config)# interface port-channel 128 ignored port-channel128: internally used, configuration not allowed
Port-Channels 111, 113, 115, 119, 121, 200, 211, 222 were created manually, but 127 - 129 were not.
Nexus5k# show port-channel usage
Total 11 port-channel numbers used
============================================
Used : 111 , 113 , 115 , 119 , 121 , 127 - 129 , 200 , 211 , 222
Unused: 1 - 110 , 112 , 114 , 116 - 118 , 120 , 122 - 126 , 130 - 199
201 - 210 , 212 - 221 , 223 - 4096
[Code]......
View 3 Replies
View Related
Apr 26, 2012
I want to be able to gather some time metrics based on source IP, and destination port. Is it possiable to track how much time a user spends using a service based on it's port number. I have figured out how to capture all the data, and I can then look at timestamps, but I would like a better way if possible. Can this be done at the firewall, or do I need a different appliance?
View 1 Replies
View Related
Mar 26, 2011
I have some tunnels which terminate to my home router. I'm allowing the other ends of the tunnels to use my voice setup. I need to prepend *67 to all called numbers which don't originate from my house. I don't want people calling my home number based on the caller-id number they see when someone across one of the tunnels calls.
So if 5008 calls 212-333-4444 I want it sent to my provider as *672123334444. If 5001 calls a number, I don't want it touched. Can I do this? I can use IOS or CUCM here.
View 13 Replies
View Related
Sep 26, 2012
The first time I tried to connect to a new secured wireless network, I was prompted to a WPA key but didn't have it to hand so clicked away. Now when I click on any secured network that is showing up as in range, I get an error message saying Windows cannot connect and the selected network may be out of range.
I can connect to an unsecured network and to the desired network via ethernet cable. Secured WiFi was working fine when I was at home but I'm now in a different country, don't know if that could affect it somehow.
View 1 Replies
View Related
Jul 5, 2011
my son's laptop suddenly stopped being able to conect to internet.My daughters and my laptop still work find.I thought if i could just re-enter wireless key it would work again.he has windows 7
View 2 Replies
View Related
Apr 20, 2011
The combination of the two line are successful and the internet is working with double speed. I can access all router from my PC but sometimes I have hard time accessing the modem pages. I am not sure the reason but I thing that when I request 192.168.2.1. the request might be sometimes taken to m2 modem , that's why the modem m1 is not found.
View 3 Replies
View Related
Jun 24, 2011
Lost my wifii security code - How to re-enter network security key
View 5 Replies
View Related
Jun 21, 2012
Why I can enter router login interface through 192.168.0.1 but can not enter through 192.168.1.1?
View 1 Replies
View Related
Nov 3, 2012
how to enter the 168,192,1,1 to set a passward to my wireless router
View 1 Replies
View Related
May 2, 2011
Not able to enter 10.12 series address in LAN PC
View 12 Replies
View Related
Feb 13, 2011
when I start the router , I can't enter the IOS , and it enther the ROMMON mode , the error display probably is : the flash is invalid.I want to import an new IOS into the flash, but it says the space is not enough.how I confirm the flash is broken?It's any other ways to solve this problem except to change the flash?
View 2 Replies
View Related
Aug 12, 2011
how to enter dos mode in a windows pc without still remaining in windows interface.
View 8 Replies
View Related
Feb 17, 2012
I've been through pages and pages of Google and Bing searches, and I've found plenty who have this issue, but none who seem to get it solved. Three computers, all running Windows 7 Home Premium 64-bit, are members of a Homegroup that functioned perfectly for more than a year until Tuesday of this week. On Tuesday, I installed Windows updates and also updated from Norton 360 v5 to v6.Computer A and B don't have password protected logins to Windows; Computer C is password protected. Until Tuesday, A and B have never been required to enter a password to access shared files and folders on C. Computer A still communicates fine in both directions with B and C, without having to enter C's Windows login credentials. B can be accessed by C, but when B attempts to access the C libraries that are shared by C to the Homegroup, the appropriate shared folders are shown (Documents, Pictures, etc.), but instead of their usual icons, the icons look like this: url... and if I try to click on them, I am prompted for a Network Password like this: url... The name following "Enter your network password to connect to:" is the name of C, and the "Domain" shown below the password block is the name of B. (Domains aren't even possible with Home Premium, are they?)
If I enter C's username and password I can access C from B, but upon rebooting B it starts all over again, even if I click "Remember my credentials." Sometimes I don't get the prompt and instead am told that I don't have permission to view
View 14 Replies
View Related
Apr 8, 2011
I have just received my RV220W Small Business Router and I do not understand the manual/UI wrt VPN. In the past, I had a PPTP server running behind a NAT and I used Pass Through to get external clients (Macs) to connect to my local LAN. But now I would like to use the Cisco Router's VPN capabilities to set up VPN and shut down the PPTP server in my LAN.I have a couple of fixed IP addresses that end up on this router, wit ISP-based 'technical' domain names (e.g. foo.static.isp.com) with reverse lookup, so using those, I should be able to connect to my RV220W from the outside.
View 0 Replies
View Related
Nov 16, 2011
I have a Snapgear 560U VPN Gateway at the main office with VPN connections to several branch offices also using Snapgear 560U. Those are no longer manufactured though, so I bought a Cisco WRVS4400N for our new office. The main office has a fixed IP but the branch office ha a dynamic one. On the Snapgear's it is very clear where I need to enter the Mandatory endpoint name on the dynamic side of the tunnel, but I can't find anything on this on the Cisco WRVS4400N. So where do I enter this information so that I can make a VPN connection between the Snapgear & Cisco boxes?
View 1 Replies
View Related
