Cisco Routers :: Sa520w - Set The Port Number For Syslog?
Mar 19, 2011Is is possible to set the port number for syslog eg 192.168.75.50:20514 ? i presume the protocol would stay udp
View 3 Replies
ADVERTISEMENT
Cisco Routers :: SA 500 - Ability To Send Syslog Events To Multiple Syslog Servers
Jul 7, 2012Add the ability to send syslog events to multiple syslog servers in the SA500 Series routers. I know the functionality is currently in the RV220W because we utilized it. It would be great if you could configure the syslog servers by event type as well. For example, being able to send the kernel events to syslog server A, and all other events to syslog server B.
View 0 Replies View RelatedRouters / Switches :: What Port Number Does Ping Use
Apr 13, 2011what port number does ping use?
View 3 Replies View RelatedCisco Firewall :: SA520W LAN Port Don't Work Correctly
Nov 20, 2012I have a problems with one SA520W.The LAN port don't work correctly. If i connect PC directly via ethernet cable (i try 2 different cable and 2 different PC) the DHCP don't assign an IP. If i reset to factory default and manual insert IP (192.168.75.1) don't work.
View 2 Replies View RelatedCisco Routers :: SA520W Does Not Get IP On Optional WAN
Feb 9, 2012We are using a SA520W as our primary router and have a fiber connection attached to the default WAN interface. We would like to improve our uptime using a secondary internet connection on the optional WAN interface.
We have bought a dovado tiny 4g router for this other connection. It acts as a dhcp server but the Cisco router does not get an IP from the dovado router. The router works as expected when connected to a normal computer. But somehow the cisco router doesnt get an IP.
I have also tried to set a static IP for the Cisco router but that didn't work either. The dovado router is setup do deliver ip in the range 192.168.0.2-254
Cisco Routers :: Can Connect SA520W To RV082
Sep 25, 2012I wanted to know if you can connect a Cable modem to a SA520W, then connect a RV082 to the SA520W?
View 5 Replies View RelatedCisco Routers :: SA520W IPSec With VPN Client
Dec 14, 2009I have a problem to configure a IPSEC VPN on the SA520W ( 1.0.39) with Cisco VPN Client (5.0.05.290). In the logs are following error:
ERROR: Could not find configuration for x.x.x.xERROR: Could not find configuration for x.x.x.xERROR: Could not find configuration for x.x.x.xERROR: Could not find configuration for x.x.x.x
Cisco Routers :: SA520W Bridging Between To Private Lans
Jun 28, 2012connecting to separate private lans:
A) 192.168.1.x
B) 192.168.0.x
A is behind a Watchguard XTM25 11.5.3
B is behind a CISCO SA520W
Both have static public facing IP's.
B only has a IP based PBX system attached to it over a SIP ALG. (originally it was hooked up to the watchguard but they didn't play nice, but works great with the Cisco. Problem is the Cisco don't have all the features of the Watchguard)
A has all my users workstations attached. The issue is that computers on A need to talk to server on B for a desktop application to work. Since they are on separate subnets, it isn't working. The app itself still doesn't work by port forward/sNats, etc.
A & B are right next to each other, so cabling between them is not an issue.
Currently, I have a cable between the watchguard and the Cisco. The watchguard end is configured with a static private ip on the subnet A (the cisco side), and plugged into the lan on the cisco side. I have a policies to let all traffic flow freeley, and from the logs on the Watchguard, all A subnet traffic is correctly going to the Cisco via said cable.
But, nothing is coming back from the Cisco. So my question is, how can I get the Cisco to play nice with the other subnet and send traffic back to the B subnet?
Cisco Routers :: SA520W - Can't Access SSLVPN Corporate Connection
Feb 27, 2013A new Windows 8 computer can't access the SSLVPN corporate connection.
When we try to access the SSLVPN website to download the launcher (you have to download the VPN launcher everytime for our configuration), you can log in and that's fine, and then you can click on the VPN Tunnel link, a popup shows up but it doesn't actually download the launcher. Solutions we've tried so far:
1) Reinstalling C++ Redistirbutable
2) Adding the site to trusted sites and allowing unsigned ActiveX controls
3) Removing all internet objects through internet options.
Is there anything else we can try?
Cisco Routers :: SA520W Response Time In Replacing A Defective Unit
Apr 17, 2013Our company just recently bought a CISCO SA520W Security Appliance from a distributor here in the Philippines. Unfortunately, after a month of use, the LAN ports on the appliance started losing power. We reported this to the distributor and they sent a CISCO engineers to check on the unit. The engineers found the unit to be defective and need to be replaced.
Three weeks after the distributor pulled-out the unit, I have followed-up the status with them. They told me that they got no definite ETA from CISCO for the replacement unit. I followed-up with them again after a week. This time, they told me that the device is already in transit and it is coming from CISCO USA but they still don't have an expected time of arrival to give me.Does it really take more than a month for CISCO to replace a brand new defective unit? The serial number of our appliance is DNI1610G0G7.
Cisco Switching/Routing :: 2960 - Remote Syslog On Different UDP / TCP Port Possible
Oct 22, 2011I have a couple of Cisco 2960's sending syslog messages to a remote syslog-ng on port 514 (standard).
I need to set another Swtich so it sends traffic to the same syslog server but on another UDP port (such as 714),, is that possible,? I cannot find the option on the documentation.
Cisco Firewall :: ASA 5500 Syslog Not Getting Captured In Centralised Syslog Server
Jan 15, 2012Recently i have upgraded the IOS of ASA5550 (in HA mode) to 8.4.2 from 8.0.5, after OS upgrade we found that the syslog from thses firewalls are not getting captured/transfered to centralised syslog server. The server is reachable from the firewalls.
View 3 Replies View RelatedCisco Switching/Routing :: 9500 Is It Possible To Change UDP Port For Syslog Messages
Jun 12, 2012Is there any way to change the port that is used for syslog messages on a Cisco 9500 switch?By default this is set to UDP port 514.There doesn't seem to be a command to change the port.
View 1 Replies View RelatedCisco WAN :: Syslog Tcp Bug For Routers (12.4 IOS)?
Feb 13, 2012when we try to configure syslog to run over tcp it seems Cisco routers (12.4) do not send proper messages as syslog server does not record anything!Tested with syslog-ng (Linux) and Kiwi (windows) and both syslog servers have the same problem.These are some indications of the possible syslog tcp problems:
[URL]
Apparently Cisco ASA (8.2) seem to process this well!
Cisco Routers :: RV042 Syslog Log Location?
Oct 13, 2011We have a RV042. We have a Debian server on the network. I have activated Enable Syslog on the RV042 router and pointed to the Debian Server IP.
Where are the logs for the Router saved on the Debian Server?
Cisco Routers :: RV110W Excessive Syslog Messages?
Mar 6, 2012I bought a RV110W wireless router a couple months ago that I've been pretty happy with.
However, I have one significant problem with it. It is configured to send syslog messages to an internal server. Twice now it has gone into a mode where it starts dumping messages like,
ip_conntrack_is_ipc_allowed: ipc_entry_is_full
continuously, at a rate of about 20 per second. It otherwise seems to function normally, but of course if unnoticed my syslog file quickly grows to hundreds or thousands of megabytes. A reboot restores normal operation. It is running firmware 1.1.0.9. A search on the internet turned up no information about this problem.
It may be some corruption is occuring in the router's OS, or perhaps this is something that can be triggered externally (in which case it would be a weak form of DoS attack? Or maybe worse if in this state it is unable to properly apply the firewall rules.)
Cisco Routers :: Cannot Send Syslog To Server From A RV082
Mar 9, 2013I'm having an issue with the syslog.
My configuration is:
LAN A (RV042)<-> GW to GW tunnel <-> (RV082) LAN B
On LAN A, I got a NAS with a syslog server. On the RV042, I've set the parameters for the syslog server, and it's working fine. On the RV082, I've set the same parameters and noting is happening.
As troubleshooting, I've done the following:
-On the RV082, I can ping the NAS without problems.
-On the RV082, I've set my computer IP adress as syslog server IP and with packet analyser, I not seing any UDP packets.
How To Find Port Number Of Any Url
May 28, 2012How to know port number of any URL, for example what is port number used by google.
View 19 Replies View RelatedCisco Wireless :: 1813 Radius Port Number In WLC
Apr 19, 2012End user has APs config with Radius server, working fine
-server 10.42.1.21 auth-port 1645 acct-port 1646
-server 10.36.1.46 auth-port 1645 acct-port 1646
In some weeks all APs will be migrated to WLC. My doubt is regarding the config in RADIUS Athentication Server port number field. There is only one option for adding.Which port number should I use? , When a new server is added always show 1812 port number; documentation states that is for authentication and 1813 for accounting.
Cisco Switching/Routing :: MAC Without Port Number Cat6500
Oct 30, 2012We have IP device on the farm switch(cat6500, which is an access layer siwtch), with the gateway on the core switches (Nexus7000), on the core when I do show ip arp, I found the mac.But when I do sh mac add add of that mac there is no port attached to that mac.
Since that particular vlan only resides on the cat 6500 and two cores, so I logged in to the 6500, and when I show mac- in that vlan, I didn’t find that mac addresss. Instead, I found another mac address with last 8bit are the same of that mac.
Is it some kind VIP of the mac? How so, if no port, how can the switch forward the frame? [code]
8636 Has Only One Box To Enter Port Number Under Each Heading?
Feb 15, 2013I changed my router from Belkin F5D 7633-4 (G) to Belkin F5D 8636-4 v2 (N) on the 7633 I was able to set up virtual server page and access my CCTV cameras remotely with no problem but on the 8636 with the same info into virtual servers page I get "No 1 WAN address is invalid".The format of the page is slightly different the 7633 required "inbound Port" number to be put in twice in different boxes side by side and the same with "Private Port".The 8636 has only one box to enter the port number under each heading.
View 3 Replies View RelatedAAA/Identity/Nac :: ACS 5.1 Custom Smtp Port Number?
May 31, 2012I have a ACS 5.1, My mailing server does not run on standard port number of smtp (25). Need to know if i can customize the port number suiting my mailing server requirement.
View 0 Replies View RelatedCisco Switching/Routing :: 1801 Not Showing Any Port Number?
May 12, 2012I have configured the following access-list on routers fa0 interface (i am using 1801)
access-list 111 permit ip any any log
and applied it in "in" direction on Fa0 interface.
Now when i am sending ssh packets to this interface its showing below
*May 14 05:09:00.104: %SEC-6-IPACCESSLOGP: list 111 permitted tcp 172.18.128.2(0) -> 172.18.128.146(0), 1 packet
why its not showing any port number ?
Cisco :: WAP321 - Forgot Port Number For Radius Settings?
Apr 22, 2013Where can you set the port numbers for auth and accounting on a WAP321?I can see where to set up to four IP addresses for the servers themselves, shared secret etc - but nowhere can I see where the port number is configured.
In a day and age of exceptionally limited IP resources, cloud hosted services and even just a little "security through obscurity" there are many reasons for needing to set a non-standard port number for the radius server.I'm at a loss how it could be in residential products, but not small business devices?
Public / Private IP And Port Number For Remote Access?
Dec 23, 2012I would like to understand how public IP works in remote access. I do have belkin router and when I access it remote I type my public IP and after it the port number for example xxx.xxx.xxx.xxx:80 and if I would like to access an IP cam remotely in the same network i would do the same thing xxx.xxx.xxx.xxx:5656 (public IP). I do know my Public IP is unique.Thus, its quite logical I can access my devices remotely. my understanding of the port number is application specific that addresses packets in different applications in the same computer. For example port 80 is for HTTP connection used browsing the web, for chatting in MSN i will use different port number specifically for MSN...etc. my question is how I can access my belkin router remotely by typing the public IP and the port number knowing that the port number is application specific not device specific? My second question is, is it possible to access two routers in the same network remotely?
View 7 Replies View RelatedCisco Switching/Routing :: Correct Number Of Port Asic In WS-X6704-LC
Jan 1, 2012Clarifying whats the correct # of port asic in WS-X6704-LC?According to the following link (Catalyst 6500 Architectural white paper): [URL]
"In the WS-X6704-10GE line card, there are two port ASICs each supporting 2 x 10 Gigabit Ethernet ports"
While in the document: Understanding Quality of Service on the Catalyst 6500 Switch: [URL]
Table 10.
WS-X6704
Number of 10 GE Ports 4
- QoS on 10-Gigabit Ethernet Line Cards (WS-X6704-10GE)
So whats correct? 4 port asic or 2 port asic?
# Port ASIC’s on the linecard 4
# Physical Ports per Port ASIC 1
D-Link DCS-930L :: Changed Port Number Now Cannot Access Video?
Nov 26, 2011With basic "Wizard" setup I got DHCP and port 80 for the camera. It was working just fine with MyDLink and locally with DLink-ViewCam software and some local test web pages. However, we have a wireless printer on that router which also uses port 80, so when it was installed we set up a "port forward" for port 80 traffic to it for administration from other subnets. How MyDLink website is able to tunnel through our hardware firewall and the wireless routers firewall to communicate with the camera is not clear to me (perhaps someone can send me a link to an explanation??), but it works...Thus, to allow access to the camera from other subents, I wanted to change the camera's port from 80 to another, say 8181 and set up the appropriate "port forwarding for TCP and UDP. All of the steps below were from a PC within the camera's subnet/router so port forwarding is not an issue
View 5 Replies View RelatedCisco Switching/Routing :: Maximum Number Of Sessions For Port Mirroring On 4510
Apr 23, 2013Are you only able to have two sessions for port mirroring on a Cisco 4510?
View 1 Replies View RelatedCisco Switching/Routing :: Cannot Find Port Number From MAC Address Using SNMP With 3725
Dec 2, 2012I'm developing a project where I use the SNMP protocol to discover the network. By discovering the network I mean go through all the routers and switches and retrieve the IP routing table from routers and the forwarding table from switches. With the routers I have no problem. For the switches I need to know for each port the MAC addresses and the Vlans. Basically it's use SNMP to find a port number from a MAC address. To do that i followed this tutorial: [URL]
The problem is that I'm using a Cisco 3725 Router with IOS 12.4 (21) and a NM-16ESW module to work as a Switch and when I use the OID .1.3.6.1.2.1.17 corresponding to the BRIDGE-MIB as it follows:
snmpwalk -v2c -c myrouter 10.1.1.5 .1.3.6.1.2.1.17
it returns:
SNMPv2-SMI::mib-2.17.1.1.0 = Hex-STRING: 00 00 00 00 00 00
SNMPv2-SMI::mib-2.17.1.2.0 = INTEGER: 0
SNMPv2-SMI::mib-2.17.1.3.0 = INTEGER: 4
From this I guess there's no information on the router about Vlans or anything. Other thing is that when I use community string indexing it returns a timeout. My theory is that this version doesn't support indexing but I don't know.
how can I get the Port Number from a MAC address from this "switch" (it's a router working as a switch) using SNMP?
Linksys Wireless Router :: EA4500 Maximum Number Of Port Forwards
Apr 19, 2012Background: currently have a WRT320N, thinking of upgrading to an EA4500 assuming ONE feature has been improved: Port Forwarding.
Scenario: Currently I have a WRT320N router, and while it "does everything we need" it has one limitation that is now getting in the way: limitation on number of forwardable ports. In the port forwarding panel, it has 15 total rows: the first five rows can be enabled for specificaly named services (SMTP, FTP, etc). The last 10 rows are fully customizable in that we can set the name, ports and protocol.
The problem is that of the 13 total ports I currently need to forward, only ONE of them is listed in that fixed list. So, sadly, I can only use one of those first five rows. I've now filled the remaining ten custom rows, and still have need for two additional ports (for now, may need more down the road).
Trying to get creative, I figured maybe I could just spill over to the Port Range Forwarding page and add a row or two there. The only problem: it's buggy. I've found that if the Single Port Forwarding list is filled, then the Port Forwarding Range entries don't work properly. For example, if I wanted ports 12345 and 12346 forwarded to 192.168.1.5, they work fine with two single port forwarding entries. However, if I delete those, add two other port lines I need forwarded (the single list being full again), and add a port forwarding range 12345..12346, they don't work properly, ports just are closed. Only the singles work, the ranges don't.
Question: Has the EA4500 resolved this issue and allow for either more lines (i.e. 20 customizable entries instead of 10), or, better, does it just have an [Add Entry] button to allow for additional rows to be created? In today's day and age, where one single device (such as an Xbox) can take four rows, a 10-row limit is pretty sparse. Comparing it to some competitors, for example the D-Link DIR-825 (aging, but still great) allows you to add as many as you want.
I realize "expensive" firewalls like SonicWall's have virtually unlimited customization, but I don't need many of the additional features and don't want to spend $350 on a "high-end" firewall to solve the problem of needing two more ports open.
Cisco Switching/Routing :: Change Number Of Internal Port-channel On Nexus 5000
Jan 3, 2012I'm in the middle of a Nexus 5000 project and recognized today while configuring port-channels, that some of the interface numbers are reserved for internal use.
Is it possible to change or configure which port-channel interface numbers are allocated for internal use by NX-OS?
Unfortunatly I wasn't able to find a solution for this issue in the offical Nexus documentation, the search function of this forum or Google. If I did miss something or didn't look careful enough at the Nexus docs, I'm also happy with RTFM (... fine manual) responses and links to the info :-)
Additional info:
Nexus5k(config)# interface port-channel 128 ignored port-channel128: internally used, configuration not allowed
Port-Channels 111, 113, 115, 119, 121, 200, 211, 222 were created manually, but 127 - 129 were not.
Nexus5k# show port-channel usage
Total 11 port-channel numbers used
============================================
Used : 111 , 113 , 115 , 119 , 121 , 127 - 129 , 200 , 211 , 222
Unused: 1 - 110 , 112 , 114 , 116 - 118 , 120 , 122 - 126 , 130 - 199
201 - 210 , 212 - 221 , 223 - 4096
[Code]......
How To Know The Number Of Routers In The Network
Feb 13, 2013how to find out the number of routers in the network
View 1 Replies View RelatedCisco Firewall :: ASA 5505 / Track How Much Time User Spends Using Service Based On Port Number
Apr 26, 2012I want to be able to gather some time metrics based on source IP, and destination port. Is it possiable to track how much time a user spends using a service based on it's port number. I have figured out how to capture all the data, and I can then look at timestamps, but I would like a better way if possible. Can this be done at the firewall, or do I need a different appliance?
View 1 Replies View Related