Cisco Switching/Routing :: 1456 Does MSS Get Increased With Ip Tcp Adjust-mss Command
May 6, 2012
I just needed more insite into the function of the ip tcp adjust-mss command which can be used to adjust the MSS value in the tcp syn packet which passes that interface. But here is a question which I had. Consider that i have two sets of systems in my LAN one with an MTU value of 1300 ( MSS 1260 ) and with a MTU of 1500 ( MSS -1460 ). If I go ahead and put an ip tcp adjust-mss 1456 (for reducing the packet size from 1500 to 1496) on the WAN . Does the command only lower the MSS for the set of systems which have 1460 or will it also increase the MSS in the tcp syn packets send by systems with MSS of 1260 ( which can potentially break some communication ).
View 1 Replies
ADVERTISEMENT
Jun 20, 2012
I came across a interesting symptom. Refer to the following topology.
host 1 <-> R1 <-> R2 <-> FW<-> host2
host 1 is configured to send syslog to host2, however due to firewall ACL is not configured, this has caused a spike to 99% in R1 which already has 70% - 80% cpu.
My questions are :
1) Even if the firewall is sending RST back to host 1, it should not caused an 20% cpu increase in R1 cpu. Why this is so? Router model is 3620.
2) How do i prevent this from happening in future? This could potentially allow someone to send random traffic to hosts and cause network performance issue. Is there a way to turn off the RST response from the Firewall? This is an Cisco ASA.
View 1 Replies
View Related
Apr 13, 2011
I was wondering about command of Linkset subcommand at ITP7613.I have been using the Cisco7613 chassis for the ITP(SIGTRAN) service.
However, i know that the "tx-queue-depth" command is used for sctp multihoming buffersize that between primary and secondary path at the Link sub-command mode. but i can't adjust the changeover buffersize(retrieval buffer) that between link and another link at the Linkset subcommand mode.
It's above my comprehension.
My guess is that related to "plan-capacity-rcvd" command. it's right?I want to know command that adjust the buffersize of Link changeover.
View 0 Replies
View Related
Dec 8, 2011
The last few days I've been exploring options in getting rid of some old routers accross a wan connections. I have a cat 3560 to play with and I thought I would try and use the no switchport command test out routing with switch. I've got some type of route issue and I tried a few things which I thought would fix the issue but had no effect. I'll post the config and a few commands so you can see what the basic setup is.
Here we can see in the arp that it knows about both 10.7.1.2 (PC unable to ping 10.3.3.254) as well as 10.3.3.254 (ASA).I tried adding in a ip route of 10.7.0.0 255.255.0.0 10.3.3.110 as well as 10.3.3.254. Neither produced the results I wanted allowing 10.7.1.2 (PC) to ping the ASA (10.3.3.254). [code]
View 4 Replies
View Related
Feb 25, 2013
We have two catalyst 3560 switches running c3560-ipbasek9-mz.122-58.SE2.bin They are connected using etherchannel using gi 0/21 - 24 interfaces.
on 3560-1 switch, there isn't any ip-default gateway or ip route configured. It only have 1 interface vlan configured.
on 3560-2 switch, there is ip default gateway configured along with 1 interface vlan.
What i dont understand here is that, i can reach out to other subnets from 3560-1 switch in which the routing is not enabled?
View 4 Replies
View Related
Jun 2, 2012
I used to "ip routing" command in order to enable inter-vlan routing, for example with 3750 cisco. I have a 6503 cisco with SUP720 MSFC3. I was able to create some vlans but I can not configure inter-vlan routing.
sw#conf t
Enter configuration commands, one per line. End with CNTL/Z.
swsur(config)#ip routing
[Code]....
View 3 Replies
View Related
Feb 27, 2013
I have just bought two Cisco 3750 and stacked them. When in global config mode, The IP Routing Command does not exisit.
See Version below
Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 12.2(55)SE3, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Thu 05-May-11 15:40 by prod_rel_team
Image text-base: 0x00003000, data-base: 0x02800000
View 5 Replies
View Related
Mar 16, 2013
Where is the "ip routing" command in Cisco switch 6500 series?
is the ip routing enable by default accoridng to the: [URL]
View 3 Replies
View Related
Oct 28, 2012
What is the command to shutdown a cisco 1841 (say, to add a module)? I know how to reload / reboot, but does not seem to find any command with an obvious name.
View 1 Replies
View Related
Dec 10, 2012
I have a 6509 witch a sup vs-Sup2T, and I´m very confuse for to configure QoS. is diferent in the old supervisor..What is the command similar to map cos to DSCP.. look
This is a configuration in a sw 4507
qos map dscp 56 to tx-queue 1
qos map cos 1 to dscp 10
qos map cos 2 to dscp 18
qos map cos 3 to dscp 26
qos map cos 4 to dscp 34
qos map cos 5 to dscp 46
qos
In 6509 with sup2T and version 15.0.SY2 Im no sure.. I see two command
platform qos map cos-mutation testmap 4 5 6 7 0 1 2 3
and
table-map cos-discard-class-map 0 1 2 3 4 5 6 7
View 1 Replies
View Related
Mar 22, 2013
I created new VDCs. Since I have done so, there is not switchport command under the interface configuration.
The interesting this is that it is available on the admin VDC, but not the new VDC I created. I cannot create a peer VPC Peer link between my 2 Nexus switches. I did allocate ports to the new VDC and I did verify the enabled feature are the same.
why the switchport command is not available?
View 3 Replies
View Related
Nov 12, 2012
Trying to configure netflow on a 3750-X. I'm sort of copying my config from a router but, it seemd that the commandes below don't work.
Is there different set of commands to configure the source and destination.
ip flow-export source Tunnel0
ip flow-export destination 172.20.X.X 9995
View 1 Replies
View Related
Sep 23, 2012
Cisco IOS 12.4 Basic check to see if the command "ip nat pool" is available?We have 12.2 basic and I know it is in the 12.4 Advanced and 15.1 Basic versions (too large of a jump in version for management). Our budget is very limited so I am hoping that 12.4 Basic has this command.
View 2 Replies
View Related
Apr 18, 2013
I have 3560g with 15.0(2)SE2 version. I try to give different default gateways for different interfaces.I've already changed the sdm, run "ip routing" and made interest interfaces in "no switchport" with ip addresses.
my route-map is "
route-map ABC permit 10
set ip next-hop 192.168.77.3"
and it is applied on the interface with "ip policy route-map ABC" but when I try to apply it says "%PLATFORM_PBR-3-UNSUPPORTED_RMAP: Route-map ABC not supported for Policy-Based Routing" everything is fine if I change from "set ip default next-hop" to "set ip next-hop" but it is not I need in the guide of the version it is said this statement is not in unsupported list of route-map commands.[URL]
View 4 Replies
View Related
Apr 4, 2013
I am using cisco packet tracer to configure the hsrp on 3560 (c3560-advipservicesk9-mz.122-37.SE1.bin) but the standby ip Command is not available on the interface the problem in that IOS or in config
View 1 Replies
View Related
May 16, 2012
I was working on adding a Cisco 6513 to TACACS but ran into trouble. While I work on the issue offline (recreate and test another switch), I wanted to place this switch on radius temporarily.
For some reason i cant undo/delete the AAA commands in order to point to my radius server. Below was done via console: [code]
I disabled my telemetry port on the Cisco 6513 as a precaution. The IOS im using is "s72033-advipservicesk9_wan-mz.122-33.SXI5.bin".how to remove the AAA authentication statement. Hope its not intrusive cause i have a customer on the box.
View 8 Replies
View Related
Feb 18, 2013
Could some one explain what the command . ip route 10.0.0.0 255.255.255.0 0.0.0.0 . will result in?
View 8 Replies
View Related
Jan 1, 2012
Are any of the following commands supported on Nexus 5K switches when deployed with L3 card:
ip helper addressip forward-protocolip directed-broadcast
View 2 Replies
View Related
Feb 6, 2012
I am trying to use the following commands on the switch but it is not supported:
ip route-cache flow
ip flow-export destination
Attached is the output for show version and show module commands from the switch.
View 9 Replies
View Related
Dec 12, 2012
Is there a command to globally invoke rw or ro feature of SNMP on a 356024P switch?
View 2 Replies
View Related
Nov 14, 2012
i just want to ask whether i should do some configurations or not on my cisco switch 4500 L3 regarding the error of 500 invalid port command when host try to access FTP active on to FTP server, i just did static route on gig interface with no switchport mode to that host network, all traffic type was allowed except the FTP with active mode?
View 7 Replies
View Related
Nov 19, 2011
I'm trying to configure my C3550 with fast ethernet port 0/48 assigned to vlan 2 in static access mode and SVI vlan 2 configured as dhcp client.
But I see command ip address dhcp is not available on interface vlan 2:
Cat3550(config-if)#ip ad
Cat3550(config-if)#ip address ?
A.B.C.D IP address
Cat3550(config-if)#ip address
Could it be a problem related to the version running on the equipment (see below the output of sh version command not sure of what EA1 stands for)? I read here [URL] that this command was introduced in version 12.1(2)T
If it is a version problem is there any possibility to download upgraded version for free?
Cat3550>sh ve
Cisco Internetwork Operating System Software
IOS (tm) C3550 Software (C3550-I5Q3L2-M), Version 12.1(20)EA1, RELEASE
[Code].....
View 7 Replies
View Related
Jun 21, 2012
I am unable to configure an interface using the "ip igmp filter <profile #>" command on a 2960G running 12.2(58)SE2. The switch allows me to create a profile using the "ip igmp profile <profile #>" global configuration command. It also lets me enable filtering with the global "ip igmp filter" command (which I didn't see in the documentation). But, the command is not accepted when configuring an interface. "ip igmp ?" does not even show "filter" as a valid auto-complete when in configure interface mode, and the command is rejected if I try to enter it.
I verified the command worked on a much earlier version of IOS, so it must have broken somewhere along the line. I'm wary of moving up to 15.0(1)SE. Is that a major IOS change?
View 5 Replies
View Related
Feb 5, 2012
I see the command "vlan access-log ratelimit 2000" and wonder what it is that it does.
View 2 Replies
View Related
Dec 6, 2012
We're having an issue with the command "cts dot1x" when applied to an uplink interface.It basically kils the connection with this command is applied. Once you remove it, everything is back to normal, the platform is a cisco 3750x.
View 5 Replies
View Related
Sep 30, 2012
I have cisco switch 3550 IOS Version 12.1(19)EA1c.
I can configure route-map commands on that. but i can not apply that into any vlan interface. while i try to apply the following command ( ip policy route-map PBR) on VLAN int i get an error msg saying that the command is not recognized.
View 3 Replies
View Related
Apr 24, 2013
I've run into an issue with this type switch. I've a 2611xm router connected to a C2924-XL switch ((C2900XL-C3H2S-M), Version 12.0(5)WC17) Basically i configured the router as a RoTS with two sub interfaces setup with encapsulation dot1q.
View 8 Replies
View Related
Aug 29, 2012
is there a command available to run diagnostics in ASR port/SPA? the one below is from a juniper remote device. i was only able to find 'test interface' but haven't run this yet (currently in production).
View 5 Replies
View Related
Nov 15, 2012
My Nexus is a 5548-UP model, NX-OS version : 5.1(3)N2(1b)
I try to debug an OSPF and an ICMP problem using the debug ip ospf command and the debug icmp command but not output appear on the terminal. As the switch is remote, I entered the terminal monitor command of course.
SG01NX01# terminal monitor
SG01NX01# debug ip ospf 1 packets
SG01NX01# show debug
[Code].....
View 2 Replies
View Related
Apr 3, 2012
I need to enable vPC "peer-switch" command on a pair of Nexus 7018s which are currently vPC peers (primary and secondary). The STP root and Secondary root are currently configured across these switches.Can I enable the peer-switch command in this configuration without impacting services, and then modify both switches to have the same bridge priority without impacting services ? We have a few downstream 5ks which are not dual homed to both vPC peers (work in progress) so need to understand if the peer-switch command will in any way break this connectivity for now.
View 1 Replies
View Related
Jun 26, 2012
when will be the command "default interface x/x" on the Nexus 5000 platform available? Even with latest software version (5.1.3.N2.1a) it is not possible. For Nexus7000 it's working fine with 5.2 train.Is there a feature request for it? If not here it is!!It's horrible to deconfigure many interfaces especially in N5k environments with many FEXes.
View 3 Replies
View Related
Jul 17, 2012
I have a Catalyst 4500 L3 Switch Software (cat4500e UNIVERSAL-M), Version 03.02.00.XO RELEASE SOFTWARE (fc2). So I just wanted to verify that the switch only does dot1q encapsulation because the switchport trunk encapsulation dot1q command does not work.
View 3 Replies
View Related
May 3, 2013
i have 4507R with dual supervisors (WS-X4013+10GE) with IOS cat4500-ipbasek9-mz.122-46.SG.bin the supervisor module are in 3 and 4, and I want to connection port 5, but i have interface and line protocol down "inactive" error.
So I realized to use command "hw-module" to change the module to GE port. However, I am not able to use the command as" I cannot use the command "hw-module uplink" as well.
View 2 Replies
View Related
