Cisco Switching/Routing :: 3750 - Explanation Of Command
Feb 18, 2013Could some one explain what the command . ip route 10.0.0.0 255.255.255.0 0.0.0.0 . will result in?
View 8 Replies
ADVERTISEMENT
Cisco Switching/Routing :: IP Flow Command On 3750-X?
Nov 12, 2012Trying to configure netflow on a 3750-X. I'm sort of copying my config from a router but, it seemd that the commandes below don't work.
Is there different set of commands to configure the source and destination.
ip flow-export source Tunnel0
ip flow-export destination 172.20.X.X 9995
Cisco Switching/Routing :: 3750 / IP Routing Command Not Existent
Feb 27, 2013I have just bought two Cisco 3750 and stacked them. When in global config mode, The IP Routing Command does not exisit.
See Version below
Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 12.2(55)SE3, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Thu 05-May-11 15:40 by prod_rel_team
Image text-base: 0x00003000, data-base: 0x02800000
Cisco Switching/Routing :: Command To Debug Packets On 3750 Switch
Apr 18, 2012What other command can be used to debug packets on a 3750 switch ?
View 2 Replies View RelatedCisco Switching/Routing :: 2911 / NAT And Match Detailed Explanation?
Dec 8, 2011we have bought 2911 router recently has to set up VOIP line seperately for the network we have two two broadband service provider:
1. how can i use 1 line as an active and other line as a failover(when 1 line is down other line should automatically bear the traffic).clear config will be useful. NATTING using MAtch address objects( roughly )
broadband service provider 1: 97.89.X.X 255.255.252.0
broadband service provider 2: 10.0.x.x 255.255.240.0
2. there are only 20 users to set up a voip line now. here we have telecom provider where they should route the traffic to make any international calls( say telecom public ip 200.200.109.110)from lan - wan everything is allowed from wan -lan we have to allow only telcom provider IP(200.200.109.110)
Cisco Switching/Routing :: Nexus 7000 Log Entry Explanation?
Dec 4, 2011I have some error messages in the Nexus 7000 log, after searching i cannot find an adequate explanation, pretty much the only thing i can find is below and i don’t think it is very relevant to my situation. The device is in production and so reloading and pulling card willy nilly is the last resort.
Device = Nexus 7018
IOS version = 5.1(2)
Log messages=
2011 Dec 2 14:52:35 IAS01LVSWIPC01 %OC_USD-SLOT8-2-RF_CRC: OC2 received packets with CRC error from MOD 6 through XBAR slot 1/inst 1 and slot 2/inst 1 and slot 3/inst 1
[code]....
Cisco Switching/Routing :: Copy Flash Tftp Command Failed On 3750 Switch
Oct 5, 2010I have a cisco 3750 swicth which i want to load a new ios to but unfortunately there's no enough space on the flash. This means that i need to backup the cureent (old) ios to my tftp server but the command keeps failing. It always gives 'No such file or directory' error .The free space on the flash is 8mb and my new ios is about 11mb.I also went inside the directory where the old is and inputed the same copy command but to no avail.Below are some of the command failure on the swicth:
[code]....
Cisco Switching/Routing :: 2955 Explanation Needed For FCS Error Hysteresis Threshold
Feb 5, 2012One of my clients is using Cisco catalyst 2955 industrial switch.I am doing the configuration for them and come across one setting of FCS Error Hysterasis Threshold. I know FCS is Frame Check Sequence.
I do not understand is what is the meaning the setting of Hysteresis in term of percentage stand for what purpose?For example, the default is 10 percent. If I set the value to be lower 5% and what is the impact on that? Is this more stringent than default of 10% or less stringent than default of 10%?
Cisco Switching/Routing :: 3750 Switch - Eigrp Stub Static Redistributed Command Executable?
Feb 29, 2012On 3750 switch with IOS c3750-ipbasek9-mz.122-55.SE4.bin "eigrp stub static redistributed" command will be executable ?
View 1 Replies View RelatedCisco Switching/Routing :: Perform STFTP On 3750 Or 3750-X?
Jun 30, 2012Do I need the Universal image to perform stftp on a 3750 or 3750-X?
View 8 Replies View RelatedCisco Switching/Routing :: Cat 3560 No Switchport Command Test Out Routing With Switch
Dec 8, 2011The last few days I've been exploring options in getting rid of some old routers accross a wan connections. I have a cat 3560 to play with and I thought I would try and use the no switchport command test out routing with switch. I've got some type of route issue and I tried a few things which I thought would fix the issue but had no effect. I'll post the config and a few commands so you can see what the basic setup is.
Here we can see in the arp that it knows about both 10.7.1.2 (PC unable to ping 10.3.3.254) as well as 10.3.3.254 (ASA).I tried adding in a ip route of 10.7.0.0 255.255.0.0 10.3.3.110 as well as 10.3.3.254. Neither produced the results I wanted allowing 10.7.1.2 (PC) to ping the ASA (10.3.3.254). [code]
Cisco Switching/Routing :: Catalyst 3560 - Routing Enabled With / Without Default Gateway Or IP Route Command
Feb 25, 2013We have two catalyst 3560 switches running c3560-ipbasek9-mz.122-58.SE2.bin They are connected using etherchannel using gi 0/21 - 24 interfaces.
on 3560-1 switch, there isn't any ip-default gateway or ip route configured. It only have 1 interface vlan configured.
on 3560-2 switch, there is ip default gateway configured along with 1 interface vlan.
What i dont understand here is that, i can reach out to other subnets from 3560-1 switch in which the routing is not enabled?
Cisco Switching/Routing :: 6500 MSFC No IP Routing Command
Jun 2, 2012I used to "ip routing" command in order to enable inter-vlan routing, for example with 3750 cisco. I have a 6503 cisco with SUP720 MSFC3. I was able to create some vlans but I can not configure inter-vlan routing.
sw#conf t
Enter configuration commands, one per line. End with CNTL/Z.
swsur(config)#ip routing
[Code]....
Cisco Switching/Routing :: IP Routing Command In 6500?
Mar 16, 2013Where is the "ip routing" command in Cisco switch 6500 series?
is the ip routing enable by default accoridng to the: [URL]
Cisco Switching/Routing :: Stacking 3750-X With Universal Image With 3750-G Running BIN Image?
Oct 10, 2011I'm looking at adding a Cisco 3750-X switch running c3750e-universalk9-mz.122-55.SE1 (IP base license) into a stack of 3750-G switches running c3750-ipbasek9-mz.122-55.SE1.bin Given that the version and feature sets are the same I don't forsee any compatibility issues. Would there be any reason why a universal image wouldn't stack correctly with other switches running the single .bin file?
View 9 Replies View RelatedCisco Switching/Routing :: What Is The Command To Shutdown 1841
Oct 28, 2012What is the command to shutdown a cisco 1841 (say, to add a module)? I know how to reload / reboot, but does not seem to find any command with an obvious name.
View 1 Replies View RelatedCisco Switching/Routing :: Command QoS In VS-Sup2T Of 6509
Dec 10, 2012I have a 6509 witch a sup vs-Sup2T, and I´m very confuse for to configure QoS. is diferent in the old supervisor..What is the command similar to map cos to DSCP.. look
This is a configuration in a sw 4507
qos map dscp 56 to tx-queue 1
qos map cos 1 to dscp 10
qos map cos 2 to dscp 18
qos map cos 3 to dscp 26
qos map cos 4 to dscp 34
qos map cos 5 to dscp 46
qos
In 6509 with sup2T and version 15.0.SY2 Im no sure.. I see two command
platform qos map cos-mutation testmap 4 5 6 7 0 1 2 3
and
table-map cos-discard-class-map 0 1 2 3 4 5 6 7
Cisco Switching/Routing :: Nexus 7K No Switchport Command Available?
Mar 22, 2013I created new VDCs. Since I have done so, there is not switchport command under the interface configuration.
The interesting this is that it is available on the admin VDC, but not the new VDC I created. I cannot create a peer VPC Peer link between my 2 Nexus switches. I did allocate ports to the new VDC and I did verify the enabled feature are the same.
why the switchport command is not available?
Cisco Switching/Routing :: Does IOS 12.4 Basic Have (IP NAT Pool) Command Available
Sep 23, 2012Cisco IOS 12.4 Basic check to see if the command "ip nat pool" is available?We have 12.2 basic and I know it is in the 12.4 Advanced and 15.1 Basic versions (too large of a jump in version for management). Our budget is very limited so I am hoping that 12.4 Basic has this command.
View 2 Replies View RelatedCisco Switching/Routing :: 3560g And Set Ip Default Next-hop Command?
Apr 18, 2013I have 3560g with 15.0(2)SE2 version. I try to give different default gateways for different interfaces.I've already changed the sdm, run "ip routing" and made interest interfaces in "no switchport" with ip addresses.
my route-map is "
route-map ABC permit 10
set ip next-hop 192.168.77.3"
and it is applied on the interface with "ip policy route-map ABC" but when I try to apply it says "%PLATFORM_PBR-3-UNSUPPORTED_RMAP: Route-map ABC not supported for Policy-Based Routing" everything is fine if I change from "set ip default next-hop" to "set ip next-hop" but it is not I need in the guide of the version it is said this statement is not in unsupported list of route-map commands.[URL]
Cisco Switching/Routing :: 3560 Ip Command Is Not Available On Interface
Apr 4, 2013I am using cisco packet tracer to configure the hsrp on 3560 (c3560-advipservicesk9-mz.122-37.SE1.bin) but the standby ip Command is not available on the interface the problem in that IOS or in config
View 1 Replies View RelatedCisco Switching/Routing :: 6513 Removing AAA Command
May 16, 2012I was working on adding a Cisco 6513 to TACACS but ran into trouble. While I work on the issue offline (recreate and test another switch), I wanted to place this switch on radius temporarily.
For some reason i cant undo/delete the AAA commands in order to point to my radius server. Below was done via console: [code]
I disabled my telemetry port on the Cisco 6513 as a precaution. The IOS im using is "s72033-advipservicesk9_wan-mz.122-33.SXI5.bin".how to remove the AAA authentication statement. Hope its not intrusive cause i have a customer on the box.
Cisco Switching/Routing :: IP Helper Command On Nexus 5K
Jan 1, 2012Are any of the following commands supported on Nexus 5K switches when deployed with L3 card:
ip helper addressip forward-protocolip directed-broadcast
Cisco WAN :: 3750 - Command To Find Optical TX / RX
Aug 7, 2012Is there a command to find your optical tx/rx power (dBm) on a 3845? On a 3750 you can do a show int transceiver; looking for a comparable command for ISRs.
View 2 Replies View RelatedCisco Switching/Routing :: NetFlow Command Support On C4503?
Feb 6, 2012I am trying to use the following commands on the switch but it is not supported:
ip route-cache flow
ip flow-export destination
Attached is the output for show version and show module commands from the switch.
Cisco Switching/Routing :: 1456 Does MSS Get Increased With Ip Tcp Adjust-mss Command
May 6, 2012I just needed more insite into the function of the ip tcp adjust-mss command which can be used to adjust the MSS value in the tcp syn packet which passes that interface. But here is a question which I had. Consider that i have two sets of systems in my LAN one with an MTU value of 1300 ( MSS 1260 ) and with a MTU of 1500 ( MSS -1460 ). If I go ahead and put an ip tcp adjust-mss 1456 (for reducing the packet size from 1500 to 1496) on the WAN . Does the command only lower the MSS for the set of systems which have 1460 or will it also increase the MSS in the tcp syn packets send by systems with MSS of 1260 ( which can potentially break some communication ).
View 1 Replies View RelatedCisco Switching/Routing :: 3560 AP - Command To Globally Invoke RW
Dec 12, 2012Is there a command to globally invoke rw or ro feature of SNMP on a 356024P switch?
View 2 Replies View RelatedCisco Switching/Routing :: 4500 L3 / 500 Invalid Port Command
Nov 14, 2012i just want to ask whether i should do some configurations or not on my cisco switch 4500 L3 regarding the error of 500 invalid port command when host try to access FTP active on to FTP server, i just did static route on gig interface with no switchport mode to that host network, all traffic type was allowed except the FTP with active mode?
View 7 Replies View RelatedCisco Switching/Routing :: IP Address DHCP Command Not Available On C3550
Nov 19, 2011I'm trying to configure my C3550 with fast ethernet port 0/48 assigned to vlan 2 in static access mode and SVI vlan 2 configured as dhcp client.
But I see command ip address dhcp is not available on interface vlan 2:
Cat3550(config-if)#ip ad
Cat3550(config-if)#ip address ?
A.B.C.D IP address
Cat3550(config-if)#ip address
Could it be a problem related to the version running on the equipment (see below the output of sh version command not sure of what EA1 stands for)? I read here [URL] that this command was introduced in version 12.1(2)T
If it is a version problem is there any possibility to download upgraded version for free?
Cat3550>sh ve
Cisco Internetwork Operating System Software
IOS (tm) C3550 Software (C3550-I5Q3L2-M), Version 12.1(20)EA1, RELEASE
[Code].....
Cisco Switching/Routing :: IP Igmp Filter Command On 2960G?
Jun 21, 2012I am unable to configure an interface using the "ip igmp filter <profile #>" command on a 2960G running 12.2(58)SE2. The switch allows me to create a profile using the "ip igmp profile <profile #>" global configuration command. It also lets me enable filtering with the global "ip igmp filter" command (which I didn't see in the documentation). But, the command is not accepted when configuring an interface. "ip igmp ?" does not even show "filter" as a valid auto-complete when in configure interface mode, and the command is rejected if I try to enter it.
I verified the command worked on a much earlier version of IOS, so it must have broken somewhere along the line. I'm wary of moving up to 15.0(1)SE. Is that a major IOS change?
Cisco Switching/Routing :: 6506E Switch Command Meaning
Feb 5, 2012I see the command "vlan access-log ratelimit 2000" and wonder what it is that it does.
View 2 Replies View RelatedWant Clear Explanation Of NAT?
Aug 11, 2011I want clear explanation of NAT.
View 1 Replies View RelatedCisco LAN :: 3750 - Range Command / Session Hang
Oct 18, 2012I've noticed that when using the range command to configure multiple interfaces on a 3750 the SSH session oftens hangs. It's seems the more interfaces in the range command the more often it hangs. I have a feeling it also spikes up the CPU. Doesn't seem to be related to a specific version of code.
View 6 Replies View Related