Cisco WAN :: Forgot To Change Default Username And Password Of 1941 Router
May 23, 2013
i forgot to change the default username and password of 1941 router. I have alos performed WR memory on router. When i am trying to recover it through ROMMON mode i am not getting the initial configuration Dialouge through which i can change the password . I have gone through all documents available through internet for recovering the same but unable to recover it.
I just dug my router (wrt54g) out of the closet and hooked it up but I cant remember my name or password for the router. Is there anything I can do that doesn't involve paying linksys any sort of "fee"
I'm trying to change my username and password, but I don't know how. The manual is in Japanese, so I don't understand, what I need to do.
I have a wired router that seems to be on 192.168.1.1. When I installed the wireless router for the first time, I connected without cable, that may be the problem about the DHCP Server, but I don't know. Anyways, these IP don't work:
192.168.11.1 192.168.11.100
I don't get any access and therefore all my neighbors can use my connection right now. But the router itself works fine from the start.
i am using a D-Link 2730u, was trying to change the username and password for the router but it keeps saying that ACS URL is required, there is a place where i can put one but even after goggling it for a bit i didn't understand what should i put in there?
i want to change my username and password of my router cw-5354 of cd-r king but the default user and password doesn't work anymore so i can't access the control panel.
How do I change the username password in the router settings for the linksys ea4500? It only lets me change the password, I cant find an option to change the username.
I have a Cisco Aironet 1100 series access point (AP1120B) that after resetting to factory defaults the default username and password (Cisco and Cisco) aren't working in the web GUI. I am able to telnet to the AP's IP and log in with Cisco and Cisco but don't know the ENABLE password. I have tried Cisco and cisco and everything else i could think of with no luck.
I also have a Cisco Aironet AP1242AG that is doing the same thing.
I am resetting my Aironet 1231-G access points and cannot access the default username and password. Here is the information I am getting on the Console. I reset getting the amber light. Attempt to use Cisco as the Username and Password. It replies that authentication fails with the below log information.
*Mar 1 00:00:04.591: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed*Mar 1 00:00:05.868: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0*Mar 1 00:00:05.969: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 1025 messages) *Mar 1 00:00:06.104: status of voice_diag_test from WLC is false*Mar 1 00:00:07.156: STUB Called : crypto_ssl_init*Mar 1 00:00:08.198: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up*Mar 1 00:00:08.244: %SYS-5-RESTART: System restarted --Cisco IOS Software, C1200 Software (C1200-K9W8-M), Version 12.4(23c)JA2, RELEASE SOFTWARE (fc3)Technical [URL] Copyright (c) 1986-2011 by Cisco Systems, Inc.Compiled Wed 13-Apr-11 12:55 by
How do I change the username and password on my home wi-fi extender (Netgear). I can't remember my original username and password and it will not let me use the extender until I put it in.
I have tried to change the username and password using the following procedure but when I do so and reboot the router and try to login using the new userid and password it says Authentication failed. Complete these steps in order to recover your password:Shut down the router.Remove the compact flash that is at the back of the router.Power on the router.Once the Rommon1> prompt appears, enter this command:confreg 0x2142Insert the compact flash.Type reset.when you are prompted to enter the initial configuration, type No, and press Enter.At the Router> prompt, type enable.At the Router# prompt, enter the configure memory command, and press Enter in order to copy the startup configuration to the running configuration.Use the config t command in order to enter global configuration mode.Use this command in order to create a new user name and password:router(config)#username cisco privilege 15 password ciscoUse this command in order to change the boot statement:config-register x2102Use this command in order to save the configuration:write memoryReload the router, and then use the new user name and password to log in to the router.
Windows 7, WRT54G2 router. How do I change the default Linksys password from "admin" to something of my chosing? I appear not to have the Setup CD. Router is working well but it still has the original password.
I would like the ability to change the default password. Currently, when I change the default password and save the config via the web interface, neither the original password, or the new password work. I am forced to reset the device to the default config to regain access to the device.
Have a cisco router 1921 ,version 15.0,configuration register is 0x2102 and did not remember the password try to solve by GW-RTR>confreg 0x2142 give error translating "confreg"....domain server (196.46.100.2) (196.46.104.2) %Bad IP address or host name translating "confreg"....domain server (196.46.100.2) (196.46.104.2) %Unknown command or computer name, or unable to find computer address also tried this GW-RTR>confreg 0x2102 give error translating "confreg"....domain server (196.46.100.2) (196.46.104.2) %Bad IP address or host name translating "confreg"....domain server (196.46.100.2) (196.46.104.2) %Unknown command or computer name, or unable to find computer address what are the way forward to get to default settings?
i am unable to configure my blackberry phone to the wireless connection. I forgot the passphrase or password of my wireless router (Cisco- Linksys E1000). My laptop is already configured as it remember the password ...I would like to change the password..
WRT54G2. I forgot password , but have to reset anyway. Currently have desktop w/XP. a laptop w/Vista and will be adding a Widows 8 64 bit laptop.. Any special consideration for settup with the Window 8?