Cisco VPN :: ASA5505 - Bad Cryptochecksum Ignored And Setting Default Startup Configuration
Jan 9, 2012
There are two issues which are testing my resolve.
1) Bad Cryptochecksum Ignored error
2) Unable to boot to a save startup-config file.
I want to take the configuration from one ASA 5505 and move it to another ASA 5505. I copied the startup-config file from an ASA 5505 running asa821-k8.bin to an ASA running 8.222-k8 to flash using tftp. I set the boot config parameter on the new asa to flash:/startup-config which is the location of the startup file. If I use copy run start command, I over write the startup file. When I copy the startup configuration to the running configuration I get a Bad Cryptochecksum Ignored error and the startup file does not copy over to the running file. How can I resolve this issue?
View 1 Replies
ADVERTISEMENT
Nov 19, 2012
don't have an option to connect a console cable to my cisco router. The usb to serial converter will not work in windows7 only on XP.have physical access to my 881 Cisco Router. If I remember correctly these routers have a default ip address. This router is brand new, out of the box. I am thinking I can access it with the correct IP via network instead of console.
View 7 Replies
View Related
Dec 16, 2012
I am running the Startup Wizard from my browser as I do not have a Console Access for a brand new CISCO ASA and I am stucked with the User? Password ? I tried many combination and nothing worked.
View 1 Replies
View Related
Jan 18, 2012
I have a Cisco 850 router that whas having problems getting an ip address via DHCP. I did some stuff on it but that didn't work, so I rebooted the router to go back to my last saved startup config. When I turned it back on and connected t othe CLI console I got the "Would you like to enter the initial configuration dialogue?" message. Thinikng I just forgot to save anything to the startup config I went through the initial set up again and made sure to save everything to the startup config. After going through the intial config and setting up a vlan to assign DHCP to clients I saved the config and rebooted, upon reboot and connecting to the CLI console I got the same "Would you like to enter the initial configuration dialogue?" message. Tryign the setup once more and making sure everything was saved to startup config I rebooted again just to make sure the changes would stick, and sure enough they didn't. Whay is the config not saving to the startup config?
View 3 Replies
View Related
Feb 3, 2013
I'm running LMS3.2 and RME 4.3.1. I deployed a netconfig job to our network which consisted of approximately 800 devices.The report said that the job completed successfully however some of the devices didn't save thier running config to startup.
Is it possible to add a command or issue another netconfig job just to save the running config, so I can identify if the job fails on some devices? Using the tick box in the netconfig job doesn't seem to alert you if its not successful.
View 2 Replies
View Related
Mar 21, 2012
We were having a discussion in my group about startup vs running configs, and how often some network managers forget to "click save" when they configure a switch. Is there a way to configure Ciscoworks to copy the running config to the startup?
View 2 Replies
View Related
Aug 14, 2012
I was working on a Cisco 2600 series router earlier today running IOS 12.4. I ran into an issue where I could not clear the startup-config. I tried:
router#erase startup-config
router#reload
router#erase nvram
router#reload
[code]....
each time IP addresses and things got cleared but other aspects did not which should have been. In the nvram there were several files:
Router#dir
Directory of nvram:/
126 -rw- 2143 <no date> startup-config
127 ---- 5 <no date> private-config
128 -rw- 2143 <no date> underlying-config
1 ---- 49 <no date> persistent-data
2 -rw- 0 <no date> ifIndex-table
View 1 Replies
View Related
May 21, 2012
I messed up the IOS on the flash of CISCO881-SEC-K9. On reboot it booted to ROMMON which allowed me to tftp up a working IOS c880data-universalk9-mz.151-4.M3.bin. Unfortunately somewhere in my playing around the default startup configuration factory loaded on the routerhas been erased. I can load a new a config on the device but as I'm using the router to learn its useful to have the original config load when I factory reset the device. What is the factory start up config?
View 3 Replies
View Related
Jun 17, 2012
I have pair of ASA 5550 and I am trying to copy a new config to my member1 (active) as the new configuration I want to use for the pair. I want to copy this to start-up config on member1 and then reload member1 and have it copy the same config to member2 (stdby). I guess I am trying to understand if I copy the configuration to member1 and reload it, member 2(stdby) will have become active and try to copy the old configuration to member1 which I do not want.
get the commands straight that I need to execute to make sure the new startup config gets to both members without being overwritten?
View 1 Replies
View Related
Jun 12, 2013
I have reconfigured the FEX numbers attached to a Nexus 5548 running on NXOS5.2 If I do show running-config the interfaces are not there anymore. But if I do show startup-config the old Fex interfaces still shows up. I did try write erase then saved the running-config and its still there.
View 1 Replies
View Related
Feb 4, 2013
I was wondering if I can force catalyst 2960 to skip startup config stored in NVRAM and boot with no config everytime it is powered. I tried to find it on google and in cisco white papers but still no luck. I found only commands that begin with "set boot config-register ... ", but switch acts like it does not know these commands.
View 7 Replies
View Related
Jan 4, 2012
I have an 877W router that I would like to have a 2nd pre-configured backup for. I was thinking of getting another 870 series (probably an 877) router, as the more expensive wireless option is not actually required. Am I right to assume that I could simply copy the contents of my current config.txt file onto the second router?
View 4 Replies
View Related
Mar 16, 2011
We have a network consisting of a central site and a few remote offices. The sites are all connected via MPLS and also have VPNs over ADSL / internet connections as a backup. The remote offices have Cisco 837 routers for the ADSL connections which we can manage but the MPLS routers are managed by the service provider providing the MPLS connections. At the central site we have a Cisco 891 for the the MPLS connection (which we manage) and a Cisco ASA5505 for the backup VPNs.
In order to implement failover from MPLS to VPN in the event of any MPLS line going down I have tried to use ip sla monitors and tracked objects on the 891 as per Cisco's documentation. The problem that I am finding is that I can't set the number of ICMP echo failures required before the tracked route is dropped. Whenever the ip sla monitor fails to get a response the tracked route is dropped immediately. This is too sensitive as packets are occasionally dropped which results in the routes bouncing back and forth between MPLS and VPN too frequently (disconnecting users in the process).
I have tried different threshold types and values, tried configuring ip sla monitor reaction-triggers (although I don't understand what little documentation that I can find on this) and have even looked at event manager. I have been working on this for a few weeks now and am getting nowhere.
The Cisco ASA5505's implementation of ip sla monitor is much better in that it is possible to specify the number of packets but unfortunately we can't use the ASA as the default gateway for the LAN as the asymmetrical routing that occurs does not work with the firewall function of the ASA.
Any issue with ip sla monitor on IOS and managed to get it working?
View 2 Replies
View Related
Apr 20, 2011
I am ordering ASA5505-UL-BUN-K9. By default device comes with which IOS version?
View 3 Replies
View Related
Mar 4, 2012
I have a cisco asa 5505 firewall, and I have a normal home ADSL broadband router, the router currently connects via wireless to my pc.What I would like to do is basically connect the asa to my pc, then my router to my firewall.what the best thing to do here, run the aa in transparent mode, OR routed mode and do NAT on the firewall to the private ip address range of my router.
OR, would it be possible to get the outside interface of my asa to get DHCP from my broadband router so it will use a 192.168.1.x address on the outside, and then turn NAT off?
View 2 Replies
View Related
Sep 15, 2012
Any info on successfully resetting an light weight 1130 AP to the factory settings? I tried the method described in the doc for 1130 on how to reset 1130 AP to the default settings, but it was not successful. I tried shutdown the AP, and plug in the power while press and holding the Mode button for about 3 seconds.This AP has lost it association with the WLC, is there anyway i can reset the AP to factory default and put in the correct IP address again?
View 3 Replies
View Related
Jun 7, 2011
I'm trying to set up a S2S VPN between two ASA5505 SP units running ASA Version 8.2(1). I've ordered additional ADSL2 lines to handle this traffic and I'm having troubles with the configuration for the additional PPPoE connection. Here is are extracts from my current config; First the interface vlans
!
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
[code]....
The result being that I can ping the OUTSIDE interface, but get no reply from the VPN interface. I've checked ADSL lines, they are up. The two PPPoE sessions are logged in and active. I can even see the ICMP packets hit the VPN interface, but there is no reply.
View 1 Replies
View Related
Feb 23, 2013
Can I receive an answer to how can I remove the default smtp.cwjamaica.com from my Windows Outlook Account. This is a pop-up server that I wish to disconnect so I can use other facilities. This is the default server and it is no longer relevant to my location our current
View 1 Replies
View Related
Aug 27, 2012
I have bought EA4500 router recently in preparations for the Singapore fibre broadband upgrade.
But for the time being I'm using it to connect to my current Linksys WAG200G ADSL Wireless Gateway.
Here's the issue I'm currently facing. I have set my EA4500 router default IP address to 192.168.1.10 to aviod conflicts with my gateway which is using 192.168.1.1. But everytime when I connect my router to the gateway, the router's default IP address changes to 10.179.159.126 or some other random IP address by itself whenever I try to change to back. However, I'm still able to surf the internet and stuffs with that current settings.
Is there something that I could do to prevent the IP address from changing by itself? And will the same thing happen again when I upgrade to fibre broadband?
View 4 Replies
View Related
Jul 20, 2012
i have the asa5505 with asa8.4.5 and asdm 6.4.2. my asa work like site to site vpn with the other asa5505. i would be love that monitoring status of VPN. i enabled on asa logging, i puted address of smtp server, receipent email, source email, the problem is because my smtp server require authentication, TLS. how set configuration on asa5505?
configuration of logging for send notification on email.
View 3 Replies
View Related
Aug 22, 2012
Our client has a vendor who needs to establish a VPN tunnel to their own router which sits behind our Firewall.
VPN Concentrator (Vendor) <------> ASA5505 Client (7.2) <-------> 3750 Switch <-------> VPN ASA outside Interface - 208.64.1x.x4 DG - 208.64.1x.x3
ASA Inside Interface - 172.20.58.13/30
3750 Switch Interface Connected to ASA - 172.20.58.14/30 and DG - 172.20.58.13
3750 Switch Interface connected to VPN router - 172.20.58.21
VPN Router Interface connected to the 3750 - 172.20.58.22/30 DG - 172.20.58.21
I have also attached a Visio for this and the running configuration from the ASA and 3750. We don't have access to the TNS VPN router. Our responsibility is to just to make sure the tunnel comes up.
1) Create a static NAT on the ASA for Public to Private IP of the VPN router
Public - 208.64.1x.x5 / 28
Private - 172.20.58.21 / 30
Will the ASA automatically ARP for this address or do i have to configure another interface on the ASA with this public IP?
2) What would the access list look like on the ASA?
3) The client gave us some config to copy the stuff on the ASA so that they can create the tunnel but i couldn't put those commands in the ASA. How would this be applied and on what interface?
Firewall Access: The following information pertains to access between the VPN router and the
VPN concentrator. If a firewall/router is present in front of the VPN the following services need to be
allowed:
permit esp host 208.224.x.x any
permit gre host 208.224.x.x any
permit udp host 208.224.x.x any eq isakmp
permit udp host 208.224.x.x any eq non500-isakmp(code )
View 2 Replies
View Related
Mar 8, 2011
I would like to configure a cisco ASA5505 IPSEC VPN. I used the wizard and tried to connect to the outside .. does not work .. The network is configured in this manner: - ADSL router with public address and internal address 192.168.2.1 -> firewall interface inside and outside 192.168.2.2 192.168.3.1 (my network is 192.168.3.0). I used a VPN to the pools ranging from 192.168.4.1 to 192.168.4.100.
INTERNET ----- ROUTER ------ ASA5505 -------LAN
What should I change? there could be problems between the router and firewall?
View 6 Replies
View Related
Mar 17, 2012
i have the asa5505. the configuration of asa 5505 is:
: Saved
Code...
i analyzed this traffic i see problem with the nat- Asymmetric NAT rules matched for forward and reverse flows. where i made error?
View 0 Replies
View Related
Mar 22, 2012
We have had an ASA5505 for close to two years. About a year ago, we added a second ISP ("BOB") which became our primary and our old one (SBC) became our backup. I successfully modified the config for this and it's been working well.
Now we're changing our primary ISP to Comcast and getting rid of BOB, so right now we actually have 3 ISPs coming into our building.
I removed the BOB interface and routes, then added an interface for Comcast using an IP address from the range they provided as well as a static route to the gateway they provided - everything is analagous to the previous interfaces and routes, but it doesn't work. If I physically disconnect the Ethernet cable going to the Comcast cable modem, then the ASA does fail back to the SBC interface as expected. If I put the BOB interface & route back in there, it works again through BOB.
If I connect a PC to the Comcast cable modem and use an IP/Gateway they provided, the Internet connection *does* work. Using this same exact IP info in the ASA doesn't work.
Is there some other configuration item besides interfaces and static routes that I should be modifying? Is there some way I can dig deeper into the ASA to see exactly what is failing?
View 2 Replies
View Related
Dec 18, 2011
We have an ASA5505 that we need to enable hairpinning on.... In the old firmware versions, we used to be able to configure a public to private static mapping along with hairpinning by using
static (inside,outside) outside_ip inside_ip netmask 255.255.255.255
static (inside,inside) outside_ip inside_ip netmask 255.255.255.255
In 8.4, if I use object nat, the hairpin functionality works perfectly,
object network obj-insideip
nat (inside,inside) static publicip
however, since object nat only allows a single nat statement, I was attempting to use a twice nat to enable the hairpin functionality, but have been unsuccessful in coming up with the right combination of parameters for the functionality.
nat (inside,inside) source static private_object public_object destination static public_object private_object
allows hairpinning to successully work from the same machine. Meaning on any given host, I can ping itself using the private or public ip, but I can't get the right combination for hairpinning from any private host to another private host via the public ip. Other combinations have yielded icmp responses, however, they specify the private IP as the source of the reply instead of the public ip.
View 1 Replies
View Related
Apr 8, 2012
I teach in a High School and we've got about a 300 node MS Windows Network. Two MS2003 File Servers act as my DNS/WINS/DHCP servers. We have been using a WATCHGUARD FIREBOX III to act as the router/gateway between the outside external address and my internal (10.0.0.1) gateway address. All p.c's inside the network are routed to one of the Servers (10.0.0.2 or 10.0.0.4) for DNS/WINS/DHCP addressing. The servers point to 10.0.0.1 for gateway.
We are trying to replace the Watchguard Firebox with a CISCO ASA 5505 (eventually we'd like to implement VPN). When I connect the CISCO ASA, I get no internet passthrough at all.
View 1 Replies
View Related
Feb 20, 2011
I like to take log backup in ASA.. and i like to check whether any attack pattern is there?? how could i do this...?Also how could i do a best practise for this?
View 12 Replies
View Related
May 11, 2013
I am using a Cisco E4200 router today but I am moving to a ASA5505. I have a device that sets up a VPN tunnel that I want to put in my DMZ. It's called the ATT Gateway. I have attached the diagram. When I use a Cisco E4200 all I do is put the outside private ip address of 192.168.0.99 of the ATT Gateway into the DMZ of the E4200 and the VPN tunnel of the ATT Gateway comes right up. I cannot configure the DMZ to do the same with the ASA. I also need to have the laptop behind the gateway access the printers in the inside network.
View 15 Replies
View Related
Sep 28, 2011
I am trying to configure a trunk between the above two devices. I like to have vlan11 on ASA. Then I like to connect a host to my switch, and have it communicate with other devices in VLAN 11 or other vlans that reside on the ASA. Below is the config that I currently have.
ASA:
ciscoasa# show run interface Ethernet0/1
!
interface Ethernet0/1
[Code].....
View 5 Replies
View Related
Oct 17, 2011
Client has an ASA5505 anchoring an MPLS network. One of their branch offices is experiencing frequent circuit outages due to theft of copper lines. I am looking at an 881G with wireless aircard as a backup solution and creating a VPN tunnel to the ASA but am unsure about how to handle routing on the ASA. There will already be a route for the branch subnet for the MPLS network.
View 2 Replies
View Related
May 27, 2013
so we have been using our current ASA5505 for a long time. Since it only support up to 10 VPN licenses, so we buy a new ASA5505-SEC-BUN-K9(support up to 25 users).
the old ASA are running: 8.0.3 and ASDM 6.0.3
the new ASA are running: 8.2.5 and ASDM 6.4.5
I thought it would be simple as export and import the config file, but when i tried to restore, the new one is looking for a zip file but the old one doesn;t backup file in ZIP. It looks like i need to update the ASA version or/and ASDM?
I am pretty new to this and never upgrade any of these versions since I am aware of the upgrade may mess things up. So do I need to upgrade both the ASA version and the ASDM in order to restore my config? any effect if i do the upgrade? I also read some articles, we need to upgrade on the version one by one, like 8.0 to 8.1 then 8.2?
View 4 Replies
View Related
Jan 9, 2012
I am wondering if it's possible to convert a Pix 501 configuration running version 6.3(5) to a new ASA5505 which we just purchased? We have site to site VPN on this device and i am just trying to save some time. I believe Cisco TAC might have a tool to do this but i am not sure.
View 4 Replies
View Related
Aug 18, 2011
I recenly installed LMS 4 on a windows 2008 R2 system , I didnt change the default configuration of windows or ciscoworks.I just added devices and configured basic things on the LMS system .when I open ciscoworks on the server itself it starts a browser session on http port 1741 and then changes automatically to https even though the default config is browser security disabled on ciscoworks.I try to open a browser session on a mgmt station to the cisco server , it didnt work in https ( I did get the login screen but couldnt log on , probablly something to do with the certificate ) , so I open http on port 1741 and it worked , I was able to log in .After a few Hours for some strange reason I didnt have access any more from the mgmt station not in http nor in https , the only way was to access it from the server itself.I went and changed the default setting of the secure browser on LMS 4 hopping that would work , I was asked to restart the ciscoworks service for the changes to take affect , I tried to restart it but it was unsuccesful so I restart the whole server. when it came up ciscoworks didnt work most services didnt start ( like the web server ,tomcat and all the manual services and ciscoworks deamon)
View 1 Replies
View Related
