Cisco Firewall :: Possible To Convert Pix 501 Configuration Running Version 6.3(5) To New ASA5505

Jan 9, 2012

I am wondering if it's possible to convert a Pix 501 configuration running version 6.3(5) to a new ASA5505 which we just purchased? We have site to site VPN on this device and i am just trying to save some time. I believe Cisco TAC might have a tool to do this but i am not sure.

View 4 Replies


ADVERTISEMENT

Cisco Firewall :: Restore Configuration To New ASA5505 On Different ASDM Version

May 27, 2013

so we have been using our current ASA5505 for a long time. Since it only support up to 10 VPN licenses, so we buy a new ASA5505-SEC-BUN-K9(support up to 25 users).
 
the old ASA are running: 8.0.3 and ASDM 6.0.3
the new ASA are running: 8.2.5 and ASDM 6.4.5
 
I thought it would be simple as export and import the config file, but when i tried to restore, the new one is looking for a zip file but the old one doesn;t backup file in ZIP. It  looks like i need to update the ASA version or/and ASDM?
 
I am pretty new to this and never upgrade any of these versions since I am aware of the upgrade may mess things up. So do I need to upgrade both the ASA version and the ASDM in order to restore my config?  any effect if i do the upgrade? I also read some articles, we need to upgrade on the version one by one, like 8.0 to 8.1 then 8.2?

View 4 Replies View Related

Cisco Switching/Routing :: 6513 - Convert CatOS Running Configuration To IOS?

Oct 14, 2012

I have a new 6513 with 2 sup32's with IOS. This chassis will replace a working 6513 with 2 sup2's with CatOS.I would like to convert my CatOS running configs to IOS, and I know there used to be a tool for this.
 
I have searched around and found many broken links to an old Cisco tool to convert my former configs, is there any way to get this tool today?  I have tried over 20 links and not been able to find a working one yet.

View 2 Replies View Related

Cisco Firewall :: Convert ASA 8.2 Version To 8.4?

Jun 17, 2012

I try to convert a CISCO ASA 8.2 version to 8.4 BUT, I have a small or "little" problem :On Cisco ASA 8.2.x, i have a possibility to create multi-line global with different subnet.Example :
 
global (outside) 2 217.1.x.65-217.x.x.66 netmask 255.255.255.240
global (outside) 1 interface     <--  Ip interface is other subnet : 217.3.x.3
global (outside) 2 217.1.x.67 netmask 255.255.255.240
nat (inside) 1 0.0.0.0 0.0.0.0
nat (dmz2) 2 192.168.4.0 255.255.255.0
 
What is the method or solution to translate multi-global in 8.4 ? with static translation in 8.4 : i try to use different server in inside's zone, but not in same network on outside. In 8.2 Firmware, it's very easy to use that, but in 8.3-8.4 version, i don't have some idea to manipulate ...
 
interface Vlan1
description Lien vers reseau Interne Client
nameif inside
security-level 100
ip address 192.168.0.1 255.255.255.0

[code]....

View 16 Replies View Related

Cisco Firewall :: ASA5505 How To Convert 3 Group Mac Address To 6

Apr 16, 2013

Recently i bought asa 5505 to practice for my exams and i failed to connect to internet since my internet provider binds IP and mac for every users and  supports only 6 group mac address (xx-xx-xx-xx-xx-xx) format. because asa 5505 has  3 groups (xxx-xxx-xxx) mac address they are unable to provide me the connection.So my question is how can i assign 6 group mac address to asa5505.

View 2 Replies View Related

Cisco Firewall :: Configuration Migration From ASA 5540 Running 7.2 To 5525X Running 9.1

May 7, 2013

I need to replace an existing ASA 5540 with a new ASA 5525X. I would like to pre-stage and configure the new box with the existing config, migrate license and export certificate files before swapping it with the old one during a change window. The new firewall will run 9.1 on deployment. Now the same 7.2(4) cannot just be copied over to 5525X running the minimum 8.6 version. There is a Web based tool available at [URL] according to Cisco documentation but the page does not load for me (Cisco intranet only tool ?). Is there another tool for automatic conversion ?

View 3 Replies View Related

Cisco Firewall :: Convert Configuration From ASA 8.2 To 8.6?

Jun 19, 2012

Is there an script tool to convert the configuration from a  Cisco ASA 8.2 to 8.6 ?

View 1 Replies View Related

Cisco Firewall :: ASA5505-UL-BUN-K9 / By Default Device Comes With Which IOS Version

Apr 20, 2011

I am ordering  ASA5505-UL-BUN-K9. By default device comes with which IOS version?

View 3 Replies View Related

Cisco Firewall :: Upgrade Path ASA5505 From Version 7.2 To 8.4?

May 9, 2013

what the upgrade path is for 5505 ASA . I have one which is version 7.2 and need to upgrade it to 8.4(5). I have read that it needs to upgraded btwn major release versions.Not sure if I need to upgrade from 7.2 - 8.0  , then form 8.0 - 8.2, then from 8.2 - 8.3 and finally 8.3 to 8.4 or can I just upgrade from 7.2 - 8.2  and then from 8.2 - 8.4 .Also what is the minimum memory requirements for vers 8.4 .my ASA running on vers 7.2 currently has 256Mb Memory and I will be upgrading this to 512MB  before I do the upgrade the image above?

View 4 Replies View Related

Cisco Firewall :: Basic Port Forwarding ASA5505 Version 8.4 ASDM 6.4?

Nov 24, 2012

configuring the ASA particulary after the change to how NAT is implemented.  What I am trying to accomplish logically seems fairly simple, yet I cannot get it to work.  I have a Synology NAS at home that I am trying to reach via the internet.  Prior to using my ASA, I had Verizon's FIOS router as my gateway and everything forwarded with no issues.  The ports I need forwarded or reachable via the internet are TCP port 80 and 5000.I can also configure it via command line if that's the easier/preferred method.

View 11 Replies View Related

Cisco Firewall :: ASA5505 Lose Configuration If Upgrade Firewall

May 17, 2011

i have asa 5505 with the asdm v5.2 (4), and the asa v7.2(4). This platform has a base license. if i upgrade adsm and asa on v6.2(1) and v8.2(2) if I lose my license and that you need to activate them? i configured site to site vpn (this firewall and the another) that i lose my configuration if i upgrade my firewall.

View 2 Replies View Related

Cisco Firewall :: NAT Configuration On PIX 506 Version 6.3(1)?

Jun 23, 2011

I try to setting up a PIX firewall to server as firewall end point for a small network for Internet access.  I had include PIX configuration setup, I had replaced IP address information by sentence which describe them since IP Address is sensitive information in our network.
 
For some reason NAT process doesn't work in log I always receiving this kind of messages :

106011: Deny inbound (No xlate) tcp src inside:INTERNAL_HOST_IP/2490 dst inside:HOST_PUBLIC_INTERNET_IP/80
106011: Deny inbound (No xlate) tcp src inside:INTERNAL_HOST_IP/2490 dst inside:HOST_PUBLIC_INTERNET_IP/80
106011: Deny inbound (No xlate) tcp src inside:INTERNAL_HOST_IP/2491 dst inside:HOST_PUBLIC_INTERNET_IP/80PIX Configuration

[code]...

View 1 Replies View Related

Cisco Switching/Routing :: 6509 Convert CatOS Configuration To Native IOS Configuration

Jul 17, 2012

I am position to migrate from CatOS 6509 switch to native IOS 6509 switch. long time ago, there was some site to convert automatically based on copy and paste onto the tool, but i can not find.
 
Does anybody know how to convert CatOS configuration to Native IOS configuration ? It is not IOS change, but it is configuration convert.

View 1 Replies View Related

Cisco Firewall :: Object To Twice NAT Configuration ASA5505 8.4?

Dec 18, 2011

We have an ASA5505 that we need to enable hairpinning on.... In the old firmware versions, we used to be able to configure a public to private static mapping along with hairpinning by using
 
static (inside,outside) outside_ip inside_ip netmask 255.255.255.255
static (inside,inside) outside_ip inside_ip netmask 255.255.255.255
 
In 8.4, if I use object nat, the hairpin functionality works perfectly,
 
object network obj-insideip
  nat (inside,inside) static publicip
 
however, since object nat only allows a single nat statement, I was attempting to use a twice nat to enable the hairpin functionality, but have been unsuccessful in coming up with the right combination of parameters for the functionality.
 
nat (inside,inside) source static private_object public_object destination static public_object private_object
 
allows hairpinning to successully work from the same machine.  Meaning on any given host, I can ping itself using the private or public ip, but I can't get the right combination for hairpinning from any private host to another private host via the public ip.  Other combinations have yielded icmp responses, however, they specify the private IP as the source of the reply instead of the public ip.

View 1 Replies View Related

Cisco Firewall :: NAT Configuration In ASA 5510 IOS Version 8.3

Mar 8, 2011

Will give configuration of NAT for my internal users with 192.168.1.0/24 with single public IP.
 
I new to configure IOS version 8.3.

View 5 Replies View Related

Cisco Firewall :: Best Practice For Log Configuration And Backup In ASA5505

Feb 20, 2011

I like to take log backup in ASA.. and i like to check whether any attack pattern is there?? how could i do this...?Also how could i do a best practise for this?

View 12 Replies View Related

Cisco Firewall :: PIX 515E Software Should Be Compatible For Current Configuration Running

Jun 26, 2011

we have a pix 515E firewall with software version Cisco PIX Security Appliance Software Version 7.0(4) and ASDM version Device Manager Version 5.0(4). we are in a process of upgrading the software. Kindly suggest the software and ASDM version  most fit for the device. Also the software should be compatilbe for the current configuation running.

View 3 Replies View Related

Cisco Firewall :: ASA5505 DMZ Configuration Versus Linksys E4200 DMZ

May 11, 2013

I am using a Cisco E4200 router today but I am moving to a ASA5505.   I have a device that sets up a VPN tunnel that I want to put in my DMZ.   It's called the ATT Gateway.  I have attached the diagram.   When I use a Cisco E4200 all I do is put the outside private ip address of 192.168.0.99 of the ATT Gateway into the DMZ of the E4200 and the VPN tunnel of the ATT Gateway comes right up. I cannot configure the DMZ to do the same with the ASA.   I also need to have the laptop behind the gateway access the printers in the inside network. 

View 15 Replies View Related

Cisco Firewall :: Trunk Configuration Between ASA5505 And 3750 Switch

Sep 28, 2011

I am trying to configure a trunk between the above two devices. I like to have vlan11 on ASA. Then I like to connect a host to my switch, and have it communicate with other devices in VLAN 11 or other vlans that reside on the ASA. Below is the config that I currently have.

ASA:
ciscoasa# show run interface Ethernet0/1
!
interface Ethernet0/1

[Code].....

View 5 Replies View Related

Cisco WAN :: Running All Switches Running By Default Configuration And Connected To WS-C4506

Jun 11, 2013

I have 30 switched in my corporate network it’s all up and running all switches running by default configuration and connected to WS-C4506 core switch our dhcp server pooling 192.168.100.1/27 network. Now we need to configure new Vlan for finance department this department has more than 200 users. If my server distributes 192.168.200.0 range ip can vlan2 automatically assign ip 200.0 addresses to finance department.All switches running default config no ip address assigned.

View 9 Replies View Related

Cisco Firewall :: ASA5505 - Configuration To Allow Inbound / Outbound Mail Communications

Dec 26, 2011

I’m trying to configure my ASA 5505, in order to allow my inbound and outbound mail communications. Here with this mail I’ve attached a diagram which illustrates my exact network setup along with ip addresses.

In this setup I’ve enabled port forwarding on my ADSL router (port 25 and 110) and configured the ASA accordingly, and my mail server is located inside my network.

My problem is currently I can send mails from my inside network to outside but my not receiving any mails which originate from outside. I’ve attached my current ASA configuration as well,

C:UsersSuthakarDocumentsOffice_DocsThakralABC Computers

Final config on ASA5505

host name Cisco
enable password 8Ry2YjIyt7RRXU24 encrypted
password 2KFQnbNIdI.2KYOU encrypted
names
!interface Vlan1
nameif inside
security-level 100
ip address 192.168.155.201 255.255.255.0
[Code] ......

View 3 Replies View Related

Cisco :: To Tell Which Ssh Version Is Running

Apr 19, 2011

I'm not sure how to tell if I'm running ssh version 1 or ssh version 2, or both.I thought a show run would show a line like, "ip ssh version 2" or "no ip ssh version 1", but I don't see these anywhere.

View 4 Replies View Related

Cisco VPN :: How To Convert 881 Configuration To 1921

May 31, 2013

Here is a copy of my cisco 881 easy vpn config. What I need to modify so this will work on a cisco 1921.
 
 hostname BTLvpn
boot-start-markerboot system flash:c870-advipservicesk9-mz.124-11.T3.binboot-end-marker
no logging bufferedenable secret 5 XXXXXX
no aaa new-modelclock timezone EASTERN -5
crypto pki trustpoint TP-self-signed-733417695enrollment selfsignedsubject-name cn=IOS-Self-Signed-Certificate-733417695revocation-check nonersakeypair TP-self-signed-733417695
crypto pki certificate chain TP-self-signed-733417695certificate self-signed 01  30820244 308201AD A0030201(code)

View 9 Replies View Related

Cisco VPN :: ASA5505 PC Running VPN Client Is Disconnected

Feb 24, 2011

I use VPN Client 5.0.06.0110 to connect my home computer to my office, which has an ASA5505.  If my immediate network connection to the PC client is  lost while the VPN is active, I get a BSOD.  There's no problem if my DSL drops or a cable beyond my router is unplugged.  It only (and always) fails if the network cable to the PC running the VPN Client is diconnected (or if my router loses power) while the link is connected. 

View 6 Replies View Related

Cisco :: Managing WLC 4404 Running Version 6.0.202

Feb 27, 2013

I've downloaded Prime Infrastructure 1.2 eval and wanted to see what it looked from WCS that I am currently using to manage the wireless network and I added the WLC (4404) device but it list the device as  "Managed with Warning" and I can't find what the warning is. 

View 3 Replies View Related

Cisco Wireless :: WLC 5508 Running Version 7.2 - Redundancy

May 1, 2012

I have 2x WLC 5508 running version 7.2. 1st one is setup and running.  My questions is: If I want to setup Active-Passive redundancy, do I need to manually setup the 2nd one exactly as the 1st one and put them in the same group? Or is it a way to copy all of the configs I made on the 1st one over to the 2nd one?

View 4 Replies View Related

Cisco Switching/Routing :: SUB7-E/2 Running Version 15 IOS Will Not Support NAT

Aug 23, 2012

I need to confirm that the 4510R+E switch with the SUB7-E/2 running version 15 IOS will not support NAT.  I am 99% convinced that it does not but i am looking for confirmation, as i am a bit surprised by the lack of NAT support on this platform.

View 0 Replies View Related

Cisco Switching/Routing :: Why 2950 Model Not Running EI Version Of IOS

Jun 3, 2012

I have several older 2950's running on my network. This one in particular became of interest to me because I couldn't set up SSH on it or enable any QoS features on it, so I did some research. What I found was there are basically 2 versions of the IOS, c2950-i6q4l2 or c2950-i6k2l2q4. I also read that the c2950-i6q4l2 IOS versions (like the one in the switch I am referring to) have both the SI and EI feature sets integrated, but the one that gets enabled is entirely dependent upon the switch model you are running it on. Did I understand this correctly? Does the IOS check the hardware on the switch and then decide with feature set to use? If so, what is prohibiting the EI feature set from being enabled on this switch? Is there a way to force the EI feature set to be enabled since it is integrated in this image?

Cisco Internetwork Operating System Software
IOS (tm) C2950 Software (C2950-I6Q4L2-M), Version 12.1(22)EA12, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2008 by cisco Systems, Inc.
Compiled Mon 07-Jul-08 23:39 by amvarma
Image text-base: 0x80010000, data-base: 0x80570000

[code]....

View 8 Replies View Related

Cisco Wireless :: Using 5508 Controller With ACS Appliance Running Version 4.1 Or 4.2?

Apr 1, 2013

using a Cisco 5508 controller (code version 7.4.100.0) with an ACS appliance running version 4.1 or 4.2?I've found that the ACS constantly reports a 'Bad request from NAS' (Invalid message authenticator in EAP request). message. This usually indicates a mismatched shared secret but this isn't the case.The controller works fine opposite a Microsoft NPS Radius Server.

View 6 Replies View Related

Cisco Switching/Routing :: Convert Configuration From CatOS On 4006 To IOS On 4510?

Sep 26, 2012

I need to convert configuration from CatOS on 4006 to IOS on 4510. I am unable to find the conversion tool.

View 5 Replies View Related

Cisco Switching/Routing :: How To Convert Configuration Catos On 6500 To IOS Image

Jul 17, 2012

how to convert configuration catos on 6500 to IOS image.

View 3 Replies View Related

D-Link DIR-655 :: Version B Running Stock 2.0 Firmware - Cannot Connect To Internet

Aug 17, 2012

I have a DIR-655 Version B running the stock 2.0 firmware and a Motorola SB6120 cable modem and my ISP is comcast. I have had comcast come out and test my line and everything is fine. I have a desktop directly wired to the internet and several portable devices accessing the router.I cannot connect to the internet. My network is available and none of my devices ever indicate the network isn't available. When I try to load a website it just says "waiting for reply..." and nothing happens. The solution that always works is rebooting both the modem and the router. What is odd is that this problem comes and goes, I will go a week with zero issues, then I go all week with rebooting my stuff 5-8 times a day..What have I tried? I tried the settings that are recommended by Furrynuts to users complaining. I have also tried changing the wireless band settings to different channels as well.

View 6 Replies View Related

Linksys Cable / DSL :: WAG320NMac Mini Running Mac OS X Version 10.6.6 Won't Connect

Feb 7, 2011

I set up my new WAG320N yesterday. I have no problems connecting with my notebook running windows 7 or my IPad. My Mac Mini running Mac OS x version 10.6.6 simply won't connect.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved