we have a pix 515E firewall with software version Cisco PIX Security Appliance Software Version 7.0(4) and ASDM version Device Manager Version 5.0(4). we are in a process of upgrading the software. Kindly suggest the software and ASDM version most fit for the device. Also the software should be compatilbe for the current configuation running.
View 3 Replies
What would be the command to clear the df-bit on a PIX-515e running 6.3? I have tried the following:
conf t crypto ipsec df-bit clear-df inside and it doesn't take it.
I need to replace an existing ASA 5540 with a new ASA 5525X. I would like to pre-stage and configure the new box with the existing config, migrate license and export certificate files before swapping it with the old one during a change window. The new firewall will run 9.1 on deployment. Now the same 7.2(4) cannot just be copied over to 5525X running the minimum 8.6 version. There is a Web based tool available at [URL] according to Cisco documentation but the page does not load for me (Cisco intranet only tool ?). Is there another tool for automatic conversion ?
View 3 Replies View RelatedI have DSL, a firewall, patch panel and hubs.The network was already in place by three previous techs. I am not sure how the current setup is done there is no configuration map.The users in office 1 are all connected to a patch panel that then connects to hubs The second office users connect to a hub that then connects to the patch panel then connects to another hub.The internet is connected to a router that will be replaced with a firewall. Should it be setup like thisdsl modem > firewall > patch panel > hubs > Nodes
View 3 Replies View RelatedI am trying to set the PIX firewall to transparent mode.After I set it to transparent firewall, I allowed all icmp, tcp, udp traffics.Currently, any devices in the inside network can get the ip automatically from DHCP server in the outside network but cannot ping to any servers in the outside network either access the internet.Do I need additional confiration on the firewall?
Here's the configuration:
PIX Version 7.0(1)
firewall transparent
names
!
interface Ethernet0
[Code]....
I dint have any experience in Using cisco pix firewall. i got this for home lab practice.the pix can be accessed and configured by web based and CLI mode right. basic configuariton tto configure pix 515e in cli mode.
as of now im using console( hyper terminal) to access the pix. in cli based commands i need the following
1. how to assign ip address to inside ethernet and outside ethernet
2. how to enable telnet and after enabling it , can i connect my pc directly to the pix inside ethernet and do telnetting or if at all possible with (https enabled)web based config. any of these are ohk.
went at browsing to find these all i could find is web based configs. i need cli commands.
I just got my PIX515e configured and thought I had it working correctly, but on my 3745 router, the line protocol is down, I've looked through the configs for bot the PIX and the 3745 and can't seem to figure out why I don't have access.
Pix515E config:
pixfirewall# show run
: Saved
:
PIX Version 8.0(4)32
!
hostname pixfirewall
domain-name home.jkkcc.com
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
As part of my course, I have to install a brand new network, including cabling, setting up equipment etc in a room whilst ensuring that the current network system for that room is still running without any issue. How to do this as it includes taking out/changing the infrastructure in relation to cabling?
View 5 Replies View RelatedI need to redo the configuration on the new one?
View 11 Replies View RelatedI am wondering if it's possible to convert a Pix 501 configuration running version 6.3(5) to a new ASA5505 which we just purchased? We have site to site VPN on this device and i am just trying to save some time. I believe Cisco TAC might have a tool to do this but i am not sure.
View 4 Replies View RelatedI have 30 switched in my corporate network it’s all up and running all switches running by default configuration and connected to WS-C4506 core switch our dhcp server pooling 192.168.100.1/27 network. Now we need to configure new Vlan for finance department this department has more than 200 users. If my server distributes 192.168.200.0 range ip can vlan2 automatically assign ip 200.0 addresses to finance department.All switches running default config no ip address assigned.
View 9 Replies View RelatedI need to configure a Cisco pix 515e as vpn concentrator. Now the network has 2 Cisco pix in fail over - May I add a new Cisco pix in parallel and redirect the vpn tunnel on it? How do I need to make the configuration in order to work?
View 2 Replies View RelatedI have an Pix 515E firewall with Pix724-33.bin IOS. I just want to know that does this IOS support SNMPV3 or I will have to upgarde it with some other version.
View 1 Replies View RelatedIve got a problem with passing traffic through a Cisco 515e firewall.im trying to telnet to devices on the inside net, 172.16.x.x fom an outside net 10.x.x.x? ive configured a group called infrastructure and added the 10.x.x.x addresses.ive configured acl 101 inbound on the outside interface:
access-list 101 permit tcp object-group INFRASTRUCTURE any eq telnet
theres a route to the inside net:
inside 172.16.0.0 255.255.0.0 172.16.163.1
and theres a translation:
static (inside,outside) 10.4.4.34 10.4.4.34 netmask 255.255.255.255
when i try and connect, using a packet capture I can see traffic from 10.4.4.34 to the inside device 172.x.x.x on the inside interface but i cant see the traffic leave the outside interface ive used the same group infrastructure group before to connect to VM machines on the 172.x.x.x net on RDP and this wrks ok. access-list 101 permit tcp object-group INFRASTRUCTURE object-group VMs eq 3389
I have an AT&T Router that is my gateway to the internet, I have no access to it. I do have the inside ip address of it which is on my private LAN. Just for shiggles we will call it 10.25.240.1 255.255.248.0. That is my gateway address for all of my current devices.I have this shiny new ASA that I want to throw in there to eliminate a proventia and a sidewinder.
The diagram shows two stacks, these are my virtual server clusters with 3560X switches with the vlans configured, and several more switches all configured with vlan 832, connected to a 2950, which is connected to my internal 2600 router. I have 4 Vlans running on 4 different ip ranges, all controlled by the internal router, with only one vlan, let's say 832 that is trunked to the outside world. That vlan has 172.16.1.x 255.255.0.0 network attached to it. All is well, and traffic is routing behind the internal router, but I cannot seem to figure out how to get the traffic to pass thru the ASA. [code]
I have an ASA 5520 with a DMZ with private addresses that I SNAT to my outside network. From inside the DMZ I can reach servers by both the internal private IP and the public IP, except if the IP is from the server trying to connect. So, say I have server1 and server2. I can connect from server1 to server 2 with both public and private, but can't connect from server1 to server1' using the public IP. ASA logs show that packets are being denied due to land attack. DNS doctoring is not an option for me.
View 1 Replies View RelatedIs there any way of showing the currently assigned ip address for an interface configured to use DHCP on an ASA 5505?
View 2 Replies View RelatedI have a ASA 5540 VPN Premium with 2 Client-less licenses.How many anyconnect users can i accommodate with current sessions ??
View 5 Replies View RelatedI have Pix firewall 515e on inside interface its has configured with IP 192.168.0.254.And Global Nating is configured.
global (outside) 1 interface
nat (inside) 1 192.168.0.0 255.255.255.0 0 0
I want i configured Global nating only for only specific IP address E.g 192.168.0.0-192.168.0.30 and 192.168.0.200-192.168.0.254?How i do this?
I have the following network.2 WAN links termination on my PIX 515e and all internal users connected to third interface.
Problem I am facing is that I have assign manual IP to users with some have full access to Internet while others have limited.
The users are changing their IP address while others are offline and I want to restrict them.
The only way I can think off is by binding IP to MAC as e.g ( Active wall software). But can it be done on PIX 515e and if so how?
I have erased the Cisco image from my PIX 515E, and while i tried to load a new image its asking for activation key. I tried its old key. but no use.
View 1 Replies View RelatedI have a PIX 515 Ewhich does authentication for SSH via RADIUS protocol and fails over to the local database if radius server goes offline. But when the radius server comes back online, authentication still takes place through LOCAL and not the radius server. Following are the commands:
aaa-server RADIUS protocol radius
aaa-server RADIUS max-failed-attempts 3
aaa-server RADIUS deadtime 10
[Code].....
\I just configure my PIX 515E with version 7.0(4) and having problems to get traffic out on eth0 (if name outside). There is no problems between different VLAN ,all VLANs are configure on eth1. It is also possible to accass services on VLAN 10 (DMZ) from outside. The only thing I see in syslog is "Built Outbound" and "Teardown".
View 11 Replies View RelatedI have a Pix 515E running PixOS version 8.0.4 with two interfaces, inside and outside.On the inside interface, I have a Redhat Enterprise Linux 5.4 64 bits machine as an NFS server version 4 (NFSv4).On the outside interface, I have three (3) Redhat Enterprise Linux 5.4 64 bits as NFS clients.I am looking for the exact UDP and TCP ports to be added to the ACL in order to accomplish
View 1 Replies View RelatedI need ot upgrade a Cisco PIX 515 E to A Cisco ASA (not sure what type and modle yet!). the PIX currently has about 80 lines of ACLs and no VPNs. So only inside and outside interfaces and 80 lines of ACLs to be transferred over to the ASA.I was wondering if the ACLs can be transferred over to ASA as is?is there anything that I need ot watch for?
View 1 Replies View RelatedI have an issue in the Cisco PIx 515e series. The IOS is 6.1(2).I have set sepecific access-list to allow incoming traffic to inside interface. But still the TCP 3-way handshaking is dropped here. [code]
View 6 Replies View RelatedWhat would be the access-list entry to allow protocol 97? I am setting up foreign-anchor controller and need to allow protocol 97.
View 1 Replies View RelatedWould it be possible to change output style of "sh running-config" in SF-300 switches to Cisco IOS-like format (eg.: options related to the specific interface put together, add tabs) in the next release?
View 24 Replies View RelatedThere are some troubles in my 7206 vxr . The process of this problem below.
LOG:
Self decompressing the image : ####################################################################################################################################################################################################################################################################################################################################################################
[Code]...
We just switched over from a T1 line to 50/4 Mbps cable Internet. The speed was fine with the T1, but when we switched over to cable, the download speeds didn't increase. I'm getting 2-3 Mbps up and still only 1.5 Mbps down. I inherited this network a few years ago, so I didn't configure the Pix initially but I have been managing it and can't find a setting limiting the bandwidth for the liffe of me. I know it's not the Internet because when I connect a computer straight to the modem, the speed is great. As soon as I put it through the Pix though, it slows way down.
View 8 Replies View RelatedI'm trying to use port redirection to allow outside access to a internal web server. As far as I can see, everything is configured properly. The Open Port Checker tool from yougotsingle.com says that the port (80) is open. However when I goto access it the connection times out. The external address is static from my ISP, and I will call it xxx.xxx.xxx.xxx. The server is at 10.1.1.20, and is functioning properly over the LAN.
View 7 Replies View RelatedI have Cisco PIX 515E for my Lab and can't recover the password. It is not connected to the network. I have configured server, address, gateway from the monitor mode and tftp not seeing my laptop. best way to reset or recover password.
View 7 Replies View RelatedI've been struggling to get ASDM (PDM) installed and running on my PIX 515e. The PIX IOS version is 7.2.4(30) The ASDM version I've copied to flash is 524.
I've followed the Cisco documentation verbatim, however I still cannot connect via the Java ASDM client or via http. When I try to connect via http, my PIX shows the following error: "tcp access denied by acl from..." I do not this this is a security (ACL) issue as I've tested after opening everything up and still no luck.
Here's my running config (w/ the relevant statements prepended with ">>>"):
show run
: Saved
:
[Code]....
