Put Enternet 300 In My Startup Folder?

Mar 8, 2011

The IT department in my university has installed enternet 300 on all of our pc's - we have to use this to log into the inter/intranet on the campus. According to them, it is not possible to have the computer automatically log onto the system. I looked into the program, however, and found a place to put ip addresses, account and password. Note: the IT department in my school works hard but it not known for developing complete knowledge about the platforms they work on - there are many.

Is this correct is it possible to put the program in the startup folder and let the computer log on automatically? To be honest, even though most systems on campus us win 2000, I thought win 2000 had the ability to do this (log on to a network) natively, so I am a little puzzled as to why they have this on the computer.

View 1 Replies


ADVERTISEMENT

Using A Linksys Wireless-n Wrt160n With Envoy To Have Enternet Connection

Jan 12, 2013

I have been using a Linksys wireless-n wrt160n with my envoy to have enternet connection but no longer have cable internet. The envoy connects by rj45. I now have at&t air card for my internet connection. I am using Windows7 on my PC. I ned to know what hardware I need to connect the envoy to connect wireless to At&t air card.

View 7 Replies View Related

Ralink Wireless LAN Upon Startup?

Apr 21, 2012

My old wireless card I took out demands these files when I log onto administrator. I have a new usb wireless card and I want the old card to stop bothering me when I restart/start/logon my cpu.the filert61.sys on ralink wireless lan installions disk is neededthere is a browse button set to c:program filesmsimsi wireless lanardinstallerwinxpI no longer have an msi folder in program files. I don't see it show up under add/remove programs in control panel. Under device manager there are three network adapters: my current wireless usb

View 1 Replies View Related

Cannot Connect To Internet Upon Startup

Apr 22, 2012

When I fire up my PC, I cannot connect to the internet. Everything is plugged in properly, and I can ping my router and get a reply. I can even get on the internet just fine wirelessly with my netbook. To get the internet to work on my desktop, I have unplug my cable, disable my adapter, plug it back in and enable it.

View 19 Replies View Related

After Each Startup Can't Connect Wirelessly To Internet?

Sep 8, 2012

My hp pavilion g6 has always had the problem of not connecting to internet after i restart it. It shows excellent signal but cant connect to internet. This has been the case on two different routers/modems with two seperate service providers, however the problem gets fixed by turning off then back on the modem/router.

View 8 Replies View Related

Unable To Automatically Connect On Startup?

Oct 1, 2012

Ive got a wireless router and until just recently my desktop was able to connect to my network automatically. I went into network settings and made sure the "connect automatically" was checked but it did nothing. I have to manually go in and connect every time even though it recognizes that there is a network to connect to.

View 1 Replies View Related

Network Connection Hangs PC On Startup?

Dec 29, 2012

My PC boots fine (via SSD) but as soon as it passes the login screen and brings me to the desktop, the network connection icon has a circle going around it for about 30 seconds. Except the circle isnt moving, or rotating as if it's frozen and when i click on it to go into the network and sharing settings, it hangs. While this happens i can access anything else fine except internet based apps. Once it connects, everything is normal.

I use a Netgear Power line Adapter and have been for years, and have never had a problem with it. I am running Windows 7 Enterprise 64 bit.

View 1 Replies View Related

Cisco WAN :: 881 Default Ip Configuration For Startup

Nov 19, 2012

don't have an option to connect a console cable to my cisco router.  The usb to serial converter will not work in windows7 only on XP.have physical access to my 881 Cisco Router.  If I remember correctly these routers have a default ip address.   This router is brand new, out of the box.  I am thinking I can access it with the correct IP via network instead of console.

View 7 Replies View Related

Cisco :: How To Enable Automatic Startup On LMS 4.1

Feb 18, 2012

i wanna ask a question regarding automatic startup on lms 4.1, i have installed my LMS 4.1 on esxi  4.x . but recently my server sometimes down because the electricity problem. and when my friend push the power button to start the server, the LMS is not automatically active. is it possible to make it automatically active soon after my server power up ?

View 3 Replies View Related

Unable To Clear Startup Configuration / NVRAM

Aug 14, 2012

I was working on a Cisco 2600 series router earlier today running IOS 12.4. I ran into an issue where I could not clear the startup-config. I tried:

router#erase startup-config
router#reload
router#erase nvram
router#reload

[code]....

each time IP addresses and things got cleared but other aspects did not which should have been. In the nvram there were several files:

Router#dir
Directory of nvram:/
126 -rw- 2143 <no date> startup-config
127 ---- 5 <no date> private-config
128 -rw- 2143 <no date> underlying-config
1 ---- 49 <no date> persistent-data
2 -rw- 0 <no date> ifIndex-table

View 1 Replies View Related

PC Hangs At Startup / Waiting For Network Connection?

Nov 10, 2011

I'm running Win7 and have recently had problems at startup. Initially I thought this was a Skype issue as removing it seemed to work, but alas the problem remains with it uninstalled. The PC boots ok and I can open programs quickly enough, but if they need internet access they hang for 5mins or so before the block clears and all is well. I have recently changed ISP provider to BT Broadband (UK) and have a new router which sets itself up and had been working fine.

View 9 Replies View Related

Network Adapter Not Found On Startup - Windows 7?

Jan 28, 2011

Recently, nearly every time I start up my computer, I can't connect to the internet. I have internet, as says my modem, what I don't have is an internet adapter. I've checked the device manager, and network and sharing center, and it just doesn't exist. I restart a few times and by chance it finds the adapter and I can connect. I have no idea what's going on, as Googling has not worked much at all.[CODE]

View -1 Replies View Related

Computer Started Connecting To Internet On Startup

Oct 31, 2012

My computer has started connecting to the internet on startup, I do not want it to do this, the answer i have already seen on here for this does not work, so how can I stop this?

View 1 Replies View Related

After Startup Computer Takes About 15 Seconds To Identify LAN

Dec 20, 2012

After startup, the computer takes about 15 seconds for it to identify the LAN.

View 1 Replies View Related

Enabling Network Adapter At Startup In Windows 7

Jul 22, 2011

My network adapter is always disabled at startup. When I go to network and sharing centre - it shows that it is enabled. I dsable it, then enable it, and I can then go online. It is just annoying that I should have to do this each time before I can access the internet?

View 1 Replies View Related

ASUS G71gx - Wireless Disabled Upon Startup

Sep 14, 2012

I have an ASUS G71gx laptop with Windows Vista 64 bit. I noticed upon start up my wireless connection would not automatically connect. I hit diagnose and repair, and it stated that I did not have wireless connectivity turned on. I tried flipping the wireless switch on and off a few times to no avail. When I would turn it on and off, the blue LED light was OFF. Also, each time I switched it on and off, it said on the screen that the wireless LAN adapter was OFF (even if the switch was turned on). Then, I restarted the windows explorer bar a few times as well as flip the switch again. This time, the blue LED turned ON. However, the internet was still turned off. I hit diagnose and repair again and it said the same thing as previously stated. It gave me the option to repair it by turning on wireless compatibility/connectivity, so I hit that. After that it turned on and I could use it with no problem.

View 3 Replies View Related

PC Splits LAN Into 2 Networks / Won't Connect To Internet At Startup

Apr 6, 2011

I have been running my new PC for about 2 weeks now, absolutly fine, until last Saturday.When I started it up, it would not connect to the internet; so I looked into it, and found it had 'split' (is the best word I can describe it), the LAN connection into 2 seperate networks, (one of them, an Unidentified Public LAN) and couldn't connect to the internet on either of them. I figured after a few minutes of fiddeling, that the only way to prevent this from happening was to disable the Network Card and restart it.This is to say, when I go to the Network and Sharing Center, it will show two active networks, both of which cannot access the internet, both LAN. To get around it, I click on the Local Area Connection link for any of the networks, and click the 'Disable' button in the Status window.I then click connect/disconnect, and follow the troubleshooting to re-activate the connection, and it is fine.

View 8 Replies View Related

Cisco :: LMS 3.2 CiscoWorks Daemon Manager Does Not Startup

Dec 20, 2010

When trying to start CiscoWorks Daemon Manager i get the following message:"The CiscoWorks Daemon Manager service on local computer started and the stoped. Some services stop automatically if they are not in use by other services or programs."I have tring starting the service from DOS also and get,E:Program FilesCSCOpxsetupsupport>net start crmdmgtdThe CiscoWorks Daemon Manager service is starting.The CiscoWorks Daemon Manager service could not be started. The service did not report an error. More help is available by typing NET HELPMSG 3534.

View 11 Replies View Related

Dell :: DW1520 Wireless Lan Is Not Enabled On Startup

Jan 14, 2011

I seem to have a problem with my Dell DW1520 wireless LAN card installed on a Studio 1747 laptop.The LAN card seems to have a mind of its own and is rarely enabled at start up. Repeatedly restarting the laptop a few times somehow magically enables the network card though.When disabled, I can see the red cross on the task bar (network connection). The network card is not even detected and is not visible in device manager. However, when I restart the laptop a few times, the bars appear, the LAN card appears in device manager and I can connect to the wireless network.

I logged a call with Dell Technical support for this and a different issue (BSOD and restart). They replaced my motherboard and asked me to monitor the situation. While the BSOD/restart issue seems to have disappeared with the motherboard replacement, the wireless LAN card issue still remains. The person that came to install the motherboard also tried installing new drivers for the LAN card but that hasn't worked. Dell tech support now say that I must reinstall the whole Operating System (Windows 7), drivers etc from scratch.

View 16 Replies View Related

Cisco WAN :: 887VA-W Startup Wizard Missing?

Nov 17, 2012

Ive just started up a new cisco 887va-w and the startup wizard doesnt start. Is there a way to make this manually start?
 
What i tend to do is run the wizard for the basic settings then run 10-15 lines from the client (depending on adsl or vdsl config) to configure the router. But for some reason this one doesnt fire it after loging on with cisco cisco to 10.10.10.1 and changed the username and password. I just get the bebased cisco cp 'basic'. Cant see anyware on it to launch the wizard either.
 
Ive tried reset button on the back and reset to factory from cisco cp?

Software running on the unit is c800-universalk9-mz.spa.151-4,m4.bin

View 1 Replies View Related

Cisco Firewall :: PIX 506e - Cannot Browse Startup

Mar 11, 2013

I just got a PIX 506e from a friend that was not longer using it. I'm trying to get started with the configuration page. I've reset it to factory defaults, rebooted and connected up ethernet. I can ping the device at 192.168.1.1 and access it via console. I browse the site https://192.168.1.1/startup.html, get the invalid ssl certification, get a login prompt (user/pass) and as the document says I leave it blank. As soon as I hit ok it goes to the 404 error Page Not found.

View 4 Replies View Related

Dell :: XPS L502x / Intel Wi-Fi Utility Will Not Startup

Dec 6, 2012

Recently I've noticed that Intel My WIFI Utility is not starting up after reboot. I reinstalled WLAN drivers (downloaded the newest version from support.dell.com) but the problem persists. Is there any way to start it manually?I'm using Dell XPS l502x, Intel® Centrino® Wireless-N 1030, Windows 7 x64.

View 1 Replies View Related

Cisco :: Catalyst Won't Booting Up After Erase Startup-config?

May 15, 2012

i have an urgent situation that my catakyst C3550 wont booting up after i reset the startup-configuration using "erase startup-config" command. now everytime i connect to the catalyst it show me "switch: " not "switch>", i have try using "boot" command in the "switch: " session but it said"Loading ""...: permission denied"error Loading ""

View 2 Replies View Related

Windows Always Reports IP Conflict On Startup Router Often Needs To Be Restarted?

Apr 7, 2013

I have an issue that started showing up since I bought a new computer. The old computer ran XP, the new one runs Windows 7. Almost every time I start the computer I get an error message telling me Windows has detected an IP conflict. Sometimes when I click okay I get the message a second timeAbout half the time, I have no internet connection when I start up and have to restart my router, which fixes the problem (after restarting the modem, I do not need to do anything like renew with ipconfig; it just starts working). I do this so often I attached it to a power switch to make it easier than unplugging.My setup is this. My PC is connected to a router connected to my cable modem. The router is also connected to a wireless hub. This hub is used by only one device, my Wii U. I can get the error message even if my Wii U is turned off.

View 3 Replies View Related

Cannot Access The Startup Menu - Belkin F7D2301 Router?

Jan 22, 2011

I have a belkin f7d2301 and I cannot access the startup menu it says startup not found I have remove program and reinstalled it. is the disc bad. i also cannot do auto updates because it can't find startup location.

View 2 Replies View Related

Wireless :: Windows 7 Hp Netbook Wifi Not Launched On Startup?

Nov 27, 2011

my net book does not launch WiFi on startup. Wireless assistant button's light is not on. when i launch my comp it says me module(701) error.

View 1 Replies View Related

Linksys Wireless Adapters :: AE1000 Does Not Connect On Startup?

Dec 30, 2010

Ive been reading the forums up and down about this device and i notice other threads with users having the "Exact" problem im having. Only problem is im noticing a simaalar theme to ech of those threads. The issue doesnt have a resolution.
 
With that said i figured i would give this a try regaurdless. The problem i have is very simple.
 
Windows 7 Yltimate 64 bit.
Motherboard: ASUS M4A785TD-V EVO
Proc: Phenom x6
Ram: 8 Gb
 
Ive tried all USB ports (2.0) on the computer and they all exibit the same said behavior. This being that when you turn the computer off, restart it, or put it to sleep...the AE1000 will not power on and has to be unseated from the USB port and then reseated before the device is seen by the system and then and only then does it fire up, connect and work perfectly.
 
The drivers i have used have been the ones off the CD, Then i removed those and downloaded the ones from the website. These drivers have been installed after removing the entry from device manager manually after attempts to use the normal method resulted in the same behavior.
 
Also i have installed this device on my Dell E6400, Dell D620 Running Windows 7 Ultimate 32 bit and 64 bit and they also exibit the same exact behavoir.

View 9 Replies View Related

Cisco Switching/Routing :: 850 Not Saving Startup Configuration

Jan 18, 2012

I have a Cisco 850 router that whas having problems getting an ip address via DHCP. I did some stuff on it but that didn't work, so I rebooted the router to go back to my last saved startup config. When I turned it back on and connected t othe CLI console I got the "Would you like to enter the initial configuration dialogue?" message. Thinikng I just forgot to save anything to the startup config I went through the initial set up again and made sure to save everything to the startup config. After going through the intial config and setting up a vlan to assign DHCP to clients I saved the config and rebooted, upon reboot and connecting to the CLI console I got the same "Would you like to enter the initial configuration dialogue?" message. Tryign the setup once more and making sure everything was saved to startup config I rebooted again just to make sure the changes would stick, and sure enough they didn't. Whay is the config not saving to the startup config? 

View 3 Replies View Related

Cisco :: LMS 3.2 / RME 4.3.1 - Netconfig Job Not Saving Running Configuration To Startup?

Feb 3, 2013

I'm running LMS3.2 and RME 4.3.1. I deployed a netconfig job to our network which consisted of approximately 800 devices.The report said that the job completed successfully however some of the devices didn't save thier running config to startup.

Is it possible to add a command or issue another netconfig job just to save the running config, so I can identify if the job fails on some devices? Using the tick box in the netconfig job doesn't seem to alert you if its not successful.

View 2 Replies View Related

Dell :: Wi-Fi Limit Connection And Power Startup On XPS L322X

Feb 1, 2013

I got my XPS L322X yesterday, and this problem occured from the first time I turned on my laptop. Everytime I turned on or restarted my computer, I could connect to my wifi router, and everything works well in the first 3-5 minutes. But later the wifi connection turned to "limit", and if I searched for the networks again, all wifi hotspots disappeared!

And if this problem popped up, there would be a follow-up problem -- I could not turn off my computer nor restart it! If I tried to restart the computer, it stayed on the "restarting" screen for 5 minutes, and a "power_start_up_failour" error warning later. If I then restarted the computer by pushing the power button for 5 seconds, it showed that the network adapter was disabled. Enableing the adapter would start this whole problem all over again!

View 2 Replies View Related

Cisco :: Copy Running Configuration To Startup - Ciscoworks LMS 4

Mar 21, 2012

We were having a discussion in my group about startup vs running configs, and how often some network managers forget to "click save" when they configure a switch.  Is there a way to configure Ciscoworks to copy the running config to the startup? 

View 2 Replies View Related

Gigaset SE567/8 - Computer Doesn't Connect To Internet On Startup

Sep 19, 2011

I'm running Vista on my Desktop, and the router is a Gigaset SE567/8 Series. Whenever I turn my computer on, it will connect to the network, but not to the internet. I get the caution symbol in the task bar with the network icon, and it show the "identifying ( mySSID )". I have to unplug the router for 30 seconds in order to make it work correctly. This router was just installed by my ISP the other day and its been acting this way since then.

View 1 Replies View Related

TP-Link 150Mbps Wireless :: TL-WR740N No Internet Access On Startup

Dec 7, 2012

Region : Philippines
Model : TL-WR740N
Hardware Version : V4
Firmware Version : 120320
ISP : Smart Bro

i have a problem with my tp-link wr740n.everytime i restart or power up may computer. my internet is no internet access and the ip address is autoconfiguration ipv4 : 169.254.x.x but when i unplug the cable on router and plugin again. the internet is back. everyday is happening this no internet access and the ipv4 : 169.254.x.x?

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved