I have an ASUS G71gx laptop with Windows Vista 64 bit. I noticed upon start up my wireless connection would not automatically connect. I hit diagnose and repair, and it stated that I did not have wireless connectivity turned on. I tried flipping the wireless switch on and off a few times to no avail. When I would turn it on and off, the blue LED light was OFF. Also, each time I switched it on and off, it said on the screen that the wireless LAN adapter was OFF (even if the switch was turned on). Then, I restarted the windows explorer bar a few times as well as flip the switch again. This time, the blue LED turned ON. However, the internet was still turned off. I hit diagnose and repair again and it said the same thing as previously stated. It gave me the option to repair it by turning on wireless compatibility/connectivity, so I hit that. After that it turned on and I could use it with no problem.
I have an ASUS Z77 Motherboard and when I install the AI Suite II which comes on the installation disc it blocks my internet connection. When I uninstall the software my connection is fine. I am using an Ethernet connection by the way. I think it is being blocked by the component called Network iControl. As soon as that component is uninstalled my Internet connection comes back. I want to have the software, but I also want to have my connection.
I recently moved into a larger 2 story house, and for the first few months I was using a Linksys E1000 I've had for about 2 years now. It's a fine single band router, but the people upstairs and the xbox/PS3 in the living room didnt have the strongest connection.
I shopped around and finally got a ASUS RT-N66U for a really good, strong dual band router that would supposedly give better range and performance than my old E1000.
Unfortunately, since I got it everyone is having issues they never had before, namely:Signal dropping all around the house and having to search for the network much slower performance than before the xbox/PS3 cant hold a stable connection even for a few minutes now, when before you could watch Netflix HD programs easily
I've upgraded the Firmware to 3.0.0.3.178 since I heard earlier firmwares had issues, but other than that and opening my ports for qTorrent it is relatively stock settings.
My old wireless card I took out demands these files when I log onto administrator. I have a new usb wireless card and I want the old card to stop bothering me when I restart/start/logon my cpu.the filert61.sys on ralink wireless lan installions disk is neededthere is a browse button set to c:program filesmsimsi wireless lanardinstallerwinxpI no longer have an msi folder in program files. I don't see it show up under add/remove programs in control panel. Under device manager there are three network adapters: my current wireless usb
I seem to have a problem with my Dell DW1520 wireless LAN card installed on a Studio 1747 laptop.The LAN card seems to have a mind of its own and is rarely enabled at start up. Repeatedly restarting the laptop a few times somehow magically enables the network card though.When disabled, I can see the red cross on the task bar (network connection). The network card is not even detected and is not visible in device manager. However, when I restart the laptop a few times, the bars appear, the LAN card appears in device manager and I can connect to the wireless network.
I logged a call with Dell Technical support for this and a different issue (BSOD and restart). They replaced my motherboard and asked me to monitor the situation. While the BSOD/restart issue seems to have disappeared with the motherboard replacement, the wireless LAN card issue still remains. The person that came to install the motherboard also tried installing new drivers for the LAN card but that hasn't worked. Dell tech support now say that I must reinstall the whole Operating System (Windows 7), drivers etc from scratch.
Ive been reading the forums up and down about this device and i notice other threads with users having the "Exact" problem im having. Only problem is im noticing a simaalar theme to ech of those threads. The issue doesnt have a resolution.
With that said i figured i would give this a try regaurdless. The problem i have is very simple.
Windows 7 Yltimate 64 bit. Motherboard: ASUS M4A785TD-V EVO Proc: Phenom x6 Ram: 8 Gb
Ive tried all USB ports (2.0) on the computer and they all exibit the same said behavior. This being that when you turn the computer off, restart it, or put it to sleep...the AE1000 will not power on and has to be unseated from the USB port and then reseated before the device is seen by the system and then and only then does it fire up, connect and work perfectly.
The drivers i have used have been the ones off the CD, Then i removed those and downloaded the ones from the website. These drivers have been installed after removing the entry from device manager manually after attempts to use the normal method resulted in the same behavior.
Also i have installed this device on my Dell E6400, Dell D620 Running Windows 7 Ultimate 32 bit and 64 bit and they also exibit the same exact behavoir.
Region : Philippines Model : TL-WR740N Hardware Version : V4 Firmware Version : 120320 ISP : Smart Bro
i have a problem with my tp-link wr740n.everytime i restart or power up may computer. my internet is no internet access and the ip address is autoconfiguration ipv4 : 169.254.x.x but when i unplug the cable on router and plugin again. the internet is back. everyday is happening this no internet access and the ipv4 : 169.254.x.x?
ive got some problems with my HP pavilion dv6000...i have recently reinstalled pc with windows xp home edition..installed drivers recommended on the HP official webpage and in HP wireless assistent still states that Wireless and bluetooth is disabled..but in device manager is enabled. also with my audio driver .already installed but dont make any sound.
I have a westell DSL modem/router supplied by Frontier. It connects only to the telephone line and via cat5 to my main router, a cisco EA6500. Everything seems to be working fine, I just would like to understand a few things.I disabled wireless radio on the westell, enabled it on the cisco, so I have just one WIFI network active.I know I am not supposed to have two DHCP servers active, but I did not know how else to be sure the CISCO would get a good address, so I left DHCP active on the WESTELL, and also enabled it on the CISCO to provide service for the rest of the net.The WESTELL admin interface is at 192.168.1.1, and assigns addresses in this range.According to the WESTELL, the CISCO is at 192.168.1.27, which I assume was assigned by DHCP.The CISCO has an admin interface at 10.144.224.224, and assigns addresses in this range to all the other devices on my net.As I say, everything works.I can access both router admin pages with a browser on my main 10.144.224 network, and can ping both.But I don't understand why it works.What rules allow me to talk to the WESTELL admin page from the CISCO private network, but do NOT propagate the DHCP access which is at the exact same IP address.
It is great that it works. But should I really have disabled DHCP on the WESTELL and assigned a static address to the CISCO? Or is this situation actually provided for in the rules, not just a lucky accident that it works?Why does the scanner say that the CISCO DHCP is "Unknown" rather than Authorized or Unauthorized? Is there something I can or should do to get it to be "Authorized"? I can ping 192.168.1.1, but not the 192.168.1.27 (times out), and yet when I ping a non-existent 192.169.1.3 I get "Reply from 192.168.1.27: Destination host unreachable".
my laptop can't connect to a wireless network, so I have to keep it in one room connected to the modem. When I unplug it, even with the wireless switch on, it loses the connection. When I use ConfigFree, it says the wireless network device is disabled. I went to device manager and updated the driver for the network adapter, and it still said it was disabled. What should I do now?
The IT department in my university has installed enternet 300 on all of our pc's - we have to use this to log into the inter/intranet on the campus. According to them, it is not possible to have the computer automatically log onto the system. I looked into the program, however, and found a place to put ip addresses, account and password. Note: the IT department in my school works hard but it not known for developing complete knowledge about the platforms they work on - there are many.
Is this correct is it possible to put the program in the startup folder and let the computer log on automatically? To be honest, even though most systems on campus us win 2000, I thought win 2000 had the ability to do this (log on to a network) natively, so I am a little puzzled as to why they have this on the computer.
When I fire up my PC, I cannot connect to the internet. Everything is plugged in properly, and I can ping my router and get a reply. I can even get on the internet just fine wirelessly with my netbook. To get the internet to work on my desktop, I have unplug my cable, disable my adapter, plug it back in and enable it.
On my Toshiba A105, the wireless adapter (Intel PRO/Wireless 3945ABG) is disabled. When I ask it to be Enabled, it goes through the motions but then immediately disables it again.
I have a windows 7 laptop and when I connect it the a wired connection it disables the wireless & 3G connections, but when I unplug the cable it doesn't renable the connections, I have to go into the network connections and select each one and renable it again.
ok i got a toshiba a15-s129 and yet its not enabled the wifi .. the light is amber and i got the module drivers and the function keys .. i hit the function + f8 yet nothing and i also have the software for atheros and yet it says wireless network interface disabled? any clue on how to enable this wireless or how to disable the hotkeys so it will not find any settings for it ...?
I cannot connect to the internet on my laptop using wireless. It was working fine for a while and it just stopped. This is not the first time this has happened. Although i cannot remember if i caused it to start working again. My laptop wireless hardware has disabled itself. I've tried enabling/disabling and troubleshooting from what i know how to do but its still not working. This problem started yesterday.
Tech Support Guy System Info Utility version 1.0.0.1 OS Version: Microsoft Windows 7 Home Premium , Service Pack 1, 64 bit Processor: Pentium(R) Dual-Core CPU T4300 @ 2.10GHz, Intel64 Family 6 Model
how i can have internet connection again. here's what happened, i disabled the Broadcasting SSID and the after that my devices can no longer locate the wifi, and then when i cant configure the setting back to its original settings because i cannot establish a connection with the mf30 and my laptop eventhough it's via USB.
I'm configuring AIR-CAP2602I-E-K9 out of the box, literally, and I want to configure it with a static address. I paste in the following commands. [code]After the host name line is pasted in I get "ERROR!!! Command is disabled" but the rest of the commands are accepted. I do a sh capwap ip config and the get the output below which looks like that config has been taken but why not my hostname? [code] I know or hoping that the APs will contact the wireless controller since I've the ip in there for it. It just means I'll be renaming all the APs, all 18 of them!
My hp pavilion g6 has always had the problem of not connecting to internet after i restart it. It shows excellent signal but cant connect to internet. This has been the case on two different routers/modems with two seperate service providers, however the problem gets fixed by turning off then back on the modem/router.
Ive got a wireless router and until just recently my desktop was able to connect to my network automatically. I went into network settings and made sure the "connect automatically" was checked but it did nothing. I have to manually go in and connect every time even though it recognizes that there is a network to connect to.
My PC boots fine (via SSD) but as soon as it passes the login screen and brings me to the desktop, the network connection icon has a circle going around it for about 30 seconds. Except the circle isnt moving, or rotating as if it's frozen and when i click on it to go into the network and sharing settings, it hangs. While this happens i can access anything else fine except internet based apps. Once it connects, everything is normal.
I use a Netgear Power line Adapter and have been for years, and have never had a problem with it. I am running Windows 7 Enterprise 64 bit.
don't have an option to connect a console cable to my cisco router. The usb to serial converter will not work in windows7 only on XP.have physical access to my 881 Cisco Router. If I remember correctly these routers have a default ip address. This router is brand new, out of the box. I am thinking I can access it with the correct IP via network instead of console.
i wanna ask a question regarding automatic startup on lms 4.1, i have installed my LMS 4.1 on esxi 4.x . but recently my server sometimes down because the electricity problem. and when my friend push the power button to start the server, the LMS is not automatically active. is it possible to make it automatically active soon after my server power up ?
When I view web page of 1410 radio is show ethernet enabled and up but radio as disabled and down. I have tried to enable but to no avail. Is this a sign my radio has gone bad?
I had to re-install Windows 7 -64bit after my hard drive had crashed, but I can seem to get the Wireless to work. I tried following the installation order as per the following link but I couldn't install the NSS/DSS as I could not find this download for my Vostro 3700. I also read somewhere that it is not needed for Windows 7, so I left it.
I installed the WLAN 1501 Half Mini-Card (4313bgn) (R270598) driver as this is the wireless card that I have and it installs. The problem I have is that the wireless software and windows says my wireless card's radio is disabled and that I need to switch the radio on using the switch on the laptop. This laptop has a physical switch and no matter if I turn it on or off.. the radio remains off. Even the wireless light above the keyboard does not switch on.The thing is, before the hard drive crashed, my wireless worked fine. Is it possible that the switch broke too, or am I missing some kind of driver or software for the wireless switch.
I'm running 3 WLC 5508, 2 of them running image AIR-CT5500-K9-7-0-116-0.aes, one AIR-CT5500-LDPE-K9-7-0-116-0.aes.
On the 5508 running the LDPE-image, I have 9 WLANs (170,171,180,181,190,191,281,282,283), all defined with admin status "ENABLED". WLANs 180,181,281 belong to a defined AP-group, WLAN 190,191,282 belong to a different AP-group.
WLANs 180,181,190,191 are defined as H-REAP. The H-REAP APs registers without any problems at the backup WLC and switches back successfully to the primary controller after recovering from reboot. Unfortunately the WLANs 180,181,190,191 show status "DISABLED" every time the primary controller comes back and I have to enable them manually.
Doing exactly the same procedure with one of the other WLC, running AIR-CT5500-K9-7-0-116-0, I never face this problem.
