Cisco Wireless :: AIR-CAP2602I-E-K9 Command Is Disabled
Nov 5, 2012
I'm configuring AIR-CAP2602I-E-K9 out of the box, literally, and I want to configure it with a static address. I paste in the following commands. [code]After the host name line is pasted in I get "ERROR!!! Command is disabled" but the rest of the commands are accepted. I do a sh capwap ip config and the get the output below which looks like that config has been taken but why not my hostname? [code] I know or hoping that the APs will contact the wireless controller since I've the ip in there for it. It just means I'll be renaming all the APs, all 18 of them!
View 6 Replies
ADVERTISEMENT
Jan 21, 2012
I have a lwapp 1130 here and it's no longer associated with the controller. I issued the clear lwapp private-config, it went through and cleared the config. Now when I try to issue the lwapp commands to set the ip and such i get ERROR!!! Command is disabled. I read that this means the static configuration is locked, but it did not say how to "unlock" it. how to get this re-enabled.
View 31 Replies
View Related
Jun 11, 2013
How are certain settings/config transfered across to the AP's from the WLC, e.g. username and passwords, snmp strings etc.... I assume this is when the AP joins the WLC.More to the topic of the original question I had in mind, is it possible and if so, how? - to configure snmp read and write string from the WLC and push this config out to AP's. I can't believe someone will have to sit down (me) and SSH to 150+ AP's per WLC to configure SNMP.
One of the buildings lost connectivity to the WLC's breifly a couple of days ago and all seemed to have lost their SNMP settings. Connectivity was restored, but couldnt poll the APs. When I SSH'd on to a couple of AP's, and manually configured the snmp-server community xxxx ro - SNMP started working again. Since there are many, there must be an easier way of doing it.I've tried resetting the AP from the WLC and also powering down AP's and bringing them back up.
Using WLC 5508 on 7.4.100
Using AP's 2602 on IOS 15.2(2)JB$
View 1 Replies
View Related
Jan 19, 2012
ive got some problems with my HP pavilion dv6000...i have recently reinstalled pc with windows xp home edition..installed drivers recommended on the HP official webpage and in HP wireless assistent still states that Wireless and bluetooth is disabled..but in device manager is enabled. also with my audio driver .already installed but dont make any sound.
View 2 Replies
View Related
Dec 28, 2011
Currently Being Moderated Wireless users getting disabled
View 6 Replies
View Related
Jan 28, 2011
I tryed going into bios and disabled it and reabled it still its not working, tryed to uninstall it and reinstalled it still not working
View 1 Replies
View Related
Feb 16, 2013
I have a westell DSL modem/router supplied by Frontier. It connects only to the telephone line and via cat5 to my main router, a cisco EA6500. Everything seems to be working fine, I just would like to understand a few things.I disabled wireless radio on the westell, enabled it on the cisco, so I have just one WIFI network active.I know I am not supposed to have two DHCP servers active, but I did not know how else to be sure the CISCO would get a good address, so I left DHCP active on the WESTELL, and also enabled it on the CISCO to provide service for the rest of the net.The WESTELL admin interface is at 192.168.1.1, and assigns addresses in this range.According to the WESTELL, the CISCO is at 192.168.1.27, which I assume was assigned by DHCP.The CISCO has an admin interface at 10.144.224.224, and assigns addresses in this range to all the other devices on my net.As I say, everything works.I can access both router admin pages with a browser on my main 10.144.224 network, and can ping both.But I don't understand why it works.What rules allow me to talk to the WESTELL admin page from the CISCO private network, but do NOT propagate the DHCP access which is at the exact same IP address.
It is great that it works. But should I really have disabled DHCP on the WESTELL and assigned a static address to the CISCO? Or is this situation actually provided for in the rules, not just a lucky accident that it works?Why does the scanner say that the CISCO DHCP is "Unknown" rather than Authorized or Unauthorized? Is there something I can or should do to get it to be "Authorized"? I can ping 192.168.1.1, but not the 192.168.1.27 (times out), and yet when I ping a non-existent 192.169.1.3 I get "Reply from 192.168.1.27: Destination host unreachable".
View 4 Replies
View Related
Apr 17, 2011
my laptop can't connect to a wireless network, so I have to keep it in one room connected to the modem. When I unplug it, even with the wireless switch on, it loses the connection. When I use ConfigFree, it says the wireless network device is disabled. I went to device manager and updated the driver for the network adapter, and it still said it was disabled. What should I do now?
View 6 Replies
View Related
Sep 26, 2012
I connected AP 1522 to AC power source and this is the message that i received on the console port.
%CDP_PD-2-POWER_LOW: All radios disabled - AC_ADAPTOR (0000.0000.0000)
Why this message apear ?This is not sufficient power to bring up radio interfaces?
View 5 Replies
View Related
Jul 6, 2005
When I view web page of 1410 radio is show ethernet enabled and up but radio as disabled and down. I have tried to enable but to no avail. Is this a sign my radio has gone bad?
View 3 Replies
View Related
Sep 4, 2012
I'm running 3 WLC 5508, 2 of them running image AIR-CT5500-K9-7-0-116-0.aes, one AIR-CT5500-LDPE-K9-7-0-116-0.aes.
On the 5508 running the LDPE-image, I have 9 WLANs (170,171,180,181,190,191,281,282,283), all defined with admin status "ENABLED".
WLANs 180,181,281 belong to a defined AP-group, WLAN 190,191,282 belong to a different AP-group.
WLANs 180,181,190,191 are defined as H-REAP. The H-REAP APs registers without any problems at the backup WLC and switches back successfully to the primary controller after recovering from reboot. Unfortunately the WLANs 180,181,190,191 show status "DISABLED" every time the primary controller comes back and I have to enable them manually.
Doing exactly the same procedure with one of the other WLC, running AIR-CT5500-K9-7-0-116-0, I never face this problem.
View 5 Replies
View Related
Dec 27, 2012
On my Toshiba A105, the wireless adapter (Intel PRO/Wireless 3945ABG) is disabled. When I ask it to be Enabled, it goes through the motions but then immediately disables it again.
View 2 Replies
View Related
Feb 15, 2011
I have a windows 7 laptop and when I connect it the a wired connection it disables the wireless & 3G connections, but when I unplug the cable it doesn't renable the connections, I have to go into the network connections and select each one and renable it again.
View 6 Replies
View Related
Sep 14, 2012
I have an ASUS G71gx laptop with Windows Vista 64 bit. I noticed upon start up my wireless connection would not automatically connect. I hit diagnose and repair, and it stated that I did not have wireless connectivity turned on. I tried flipping the wireless switch on and off a few times to no avail. When I would turn it on and off, the blue LED light was OFF. Also, each time I switched it on and off, it said on the screen that the wireless LAN adapter was OFF (even if the switch was turned on). Then, I restarted the windows explorer bar a few times as well as flip the switch again. This time, the blue LED turned ON. However, the internet was still turned off. I hit diagnose and repair again and it said the same thing as previously stated. It gave me the option to repair it by turning on wireless compatibility/connectivity, so I hit that. After that it turned on and I could use it with no problem.
View 3 Replies
View Related
Oct 1, 2011
ok i got a toshiba a15-s129 and yet its not enabled the wifi .. the light is amber and i got the module drivers and the function keys .. i hit the function + f8 yet nothing and i also have the software for atheros and yet it says wireless network interface disabled? any clue on how to enable this wireless or how to disable the hotkeys so it will not find any settings for it ...?
View 1 Replies
View Related
Jul 28, 2011
I cannot connect to the internet on my laptop using wireless. It was working fine for a while and it just stopped. This is not the first time this has happened. Although i cannot remember if i caused it to start working again. My laptop wireless hardware has disabled itself. I've tried enabling/disabling and troubleshooting from what i know how to do but its still not working. This problem started yesterday.
Tech Support Guy System Info Utility version 1.0.0.1
OS Version: Microsoft Windows 7 Home Premium , Service Pack 1, 64 bit
Processor: Pentium(R) Dual-Core CPU T4300 @ 2.10GHz, Intel64 Family 6 Model
[Code].....
View 12 Replies
View Related
May 5, 2012
how i can have internet connection again. here's what happened, i disabled the Broadcasting SSID and the after that my devices can no longer locate the wifi, and then when i cant configure the setting back to its original settings because i cannot establish a connection with the mf30 and my laptop eventhough it's via USB.
View 1 Replies
View Related
Sep 11, 2011
I have a cisco e1000 route. i've already set up wireless network successfully with cisco connect software. However, when i logged in web-based config, i disabled NAT with the routing table is unchanged. the problem is anyone from the network to which the Internet WAN port links can ping and receive reply from PCs inside the wireless network but it's impossible for the reverse direction and any traffic from the inside of e1000 can't be passed through.
View 6 Replies
View Related
May 2, 2013
One week ago I use a WLC 5508 to place and replace another WLC 5508 with version 6.0.199.4, when I conect the new WLC all AP´s works OK only 10 dont work and not are recognizes from the WLC with version 7.3.101.0. The fail is the radios stay disabled. All ap´s are AIR-AP1242G-AK9 . See the image below, the only difference this ten AP´s are conected in switches cisco all the rest are connected in switches of ohter vendor. If possible some command in the configuration is not neccesary and make the bad function?This is tipically config apllied by the customer in they cisco switches interface GigabitEthernet0/22description PB-RS-A22switchport access vlan 5switchport mode accessswitchport port-securityswitchport port-security aging time 2switchport port-security violation restrictswitchport port-security aging type inactivitymacro description cisco-desktopspanning-tree portfastspanning-tree bpduguard enable?
View 4 Replies
View Related
Jul 21, 2012
I have cisco wlc 2125 and external web autherthation was configured on it. When user disable the java script in browser cisco wlc do not redirect on my external page instead of wlc show page http://1.1.1.1/login.html with cisco logo. How can i resolve this problem? How to configure wlc redirect to external web auth site with disabled java in users browser?
View 3 Replies
View Related
Apr 15, 2012
I had to re-install Windows 7 -64bit after my hard drive had crashed, but I can seem to get the Wireless to work. I tried following the installation order as per the following link but I couldn't install the NSS/DSS as I could not find this download for my Vostro 3700. I also read somewhere that it is not needed for Windows 7, so I left it.
I installed the WLAN 1501 Half Mini-Card (4313bgn) (R270598) driver as this is the wireless card that I have and it installs. The problem I have is that the wireless software and windows says my wireless card's radio is disabled and that I need to switch the radio on using the switch on the laptop. This laptop has a physical switch and no matter if I turn it on or off.. the radio remains off. Even the wireless light above the keyboard does not switch on.The thing is, before the hard drive crashed, my wireless worked fine. Is it possible that the switch broke too, or am I missing some kind of driver or software for the wireless switch.
View 11 Replies
View Related
Nov 16, 2011
On DELL latitude 6410, when i try to enable the wireless radio...I get the below mesg
WLAN card is still disabled . Use the wireless switch or hotkey to enable it
I tired using Fn F2 ...but it still remains disabled.
View 5 Replies
View Related
Mar 27, 2012
I have a wap200 wireless access point configured and connected to the switch 2690 switch on vlan1, when I connect the wireless access points to the switch the port become disabled.
View 1 Replies
View Related
May 19, 2012
When I click on the Wireless Network Connection icon it says "Wireless network unavailable." There's also an error message that says "The Dell Wireless WLAN Card is disabled. Use the Dell Wireless WLAN Utility to enable it." When I right click on the wireless network icon it says "No wireless networks were found in range. Make sure the wireless switch on your computer is on. To see an updated list, click 'Refresh network list.'" I don't have a wireless switch. I have a wireless enable icon and it says Enabled. My wireless network is working because my phone sees it and two other networks in the neighborhood. I couldn't find the Dell Wireless WLAN Utility. I also tried my iPhone hotspot. Laptop did not detect it either.
View 2 Replies
View Related
Nov 24, 2012
Bought the Zyxel Wireless Range Extender to get wifi in farthest rooms in my house but set up is not working because BT have disabled WPS button on Home Hub 3 with my Infinity. Therefore they suggest I try manual set up. This requires browser wtih IP address 192.168.1.2 for Zyxel wireless extender WRE2205, This gives no result (page does not load in IE).
View 1 Replies
View Related
Feb 23, 2012
I disabled the Bluetooth in my lap but the lights is on why? My laptops is Asus netbook 1015?
View 4 Replies
View Related
Jun 27, 2012
Linksys has disabled my wireless adaptor for wireless devices such as my Netflix streaming movie player. They are asking for my routers user name and password which I am not accessing right, I get "401 Authorization required" How do I factory restore my router? It's a D-Link DES-1105 router model BEFW1154V4. I need to enable my network for wireless connection. How to get my routers user name and password? I 've had my Netflix player hooked up and working for almost a year and have never encountered this problem. Im going to purchase a linksys wireless adaptor the first of the month with having a secure connection to linksys instead of having to wait all day for wireless linksys with the Ativa adaptor I already have?
View 2 Replies
View Related
Aug 30, 2012
Trying to secure Linksys WRT54G V8 wireless router. Can't change security mode from 'Disabled'!?
I followed this Post from EXPERT: "Connecting two routers wired - the definitive answer"
[url]...
I got the two routers working but the second one (not using it as a router) is not allowing me to change security mode from "disable" to WEP or anything else.The following Post didn't answered this issue: "Can't change wireless Security Mode on my WRT54G V5"
View 8 Replies
View Related
Jun 4, 2012
I call century link because my router was not connecting at the proper speed of 7 mbps. That problem was easily remedied over the phone but the lady said she could see several devices connected. This lost me a bit because I have a double router configuration. The Action tech PK5000 i turned into nothing more that an internet modem. I disabled the DHCP and configured my Linksys E1200 for all the internal DHCP so there is only one cable going to the PK5000. I should technically speaking look like one user on there network with natural protection from the second router.
View 5 Replies
View Related
Jul 16, 2012
I just purchased an e4200 in a corporate environment where we already have a wireless router. I am not able to connect the 2 devices via a LAN cable and am wondering if I can get bridge mode working over the network (wireless). I set the Linksys to bridge mode and assigned it an ip address. I disabled all wireless settings, etc. I then connected the internet port of the Linksys into a data port (wall jack) that connects to our flat network switch. It says it's connected under "Status" but I'm not sure how to confirm this.
View 3 Replies
View Related
Mar 20, 2013
Region : CzechRepublic
Model : TD-W8961NB
Hardware Version : V3
Firmware Version : Firmware Version : 2.0.0 Build 120823 Rel.26389
ISP : 88.103.200.11
I had a problem with this ADSL router - the VOIP outgoing calls did not work until I disabled SIP in telnet: ip nat service sip sw off.But the SIP is going to be enabled every time the router restart (or reset to default).
View 1 Replies
View Related
May 27, 2011
I press FN/F2 to "enable and disable wireless" but cannot see the antenna icon appear on the screen to know if the functionalty even exists. Other function keys work properly. I vaguely remember seeing this icon when I first purchased the laptop, but soon after purchase I had to completely reinstall the operating system and have not had a need to a wireless connection to notice it was no longer there.Because I cannot access wireless connections I assume there is a problem with enabling this feature of my laptop.
what I should be doing to check/correct that my laptop can receive a wifi connection? I've checked the recommended driver installs for my model of laptop, but nothing seems relevant.
View 4 Replies
View Related
Jan 14, 2013
We have a 5508 controller in main site.Which has two ports connected to local network.Management VLAN 500 is untagged and mapped to Port 1.All other interfaces are including 501 to 507 are mapped to Port 2.We have a SSID that is mapped to VLAN 501 interface , which successfully can be joined in main site.We connect an AP to remote site ;We have a remote site VLAN 115 which can be reached from main site.We connect an AP to access vlan 115 port on the remote site , we had described option 43 , so AP can successfully finds controller in local mode.
AP gets ip from VLAN 115 , can setup connection / ping controller successfully.There is a wide area connection between remote and main site.No trunk setup , the whole remote site is vlan 115.However when the client is trying to connect the test SSID , client cant get connected nor get ip address.Local switching is disabled.For this setup , client comes to AP as a requested , AP tunnels traffic to controller from vlan 500 , controller lets the client get into wired platform from VLAN 501.
View 25 Replies
View Related
