Cisco Wireless :: WLC 5508 - WLANs Disabled After Reboot
Sep 4, 2012
I'm running 3 WLC 5508, 2 of them running image AIR-CT5500-K9-7-0-116-0.aes, one AIR-CT5500-LDPE-K9-7-0-116-0.aes.
On the 5508 running the LDPE-image, I have 9 WLANs (170,171,180,181,190,191,281,282,283), all defined with admin status "ENABLED".
WLANs 180,181,281 belong to a defined AP-group, WLAN 190,191,282 belong to a different AP-group.
WLANs 180,181,190,191 are defined as H-REAP. The H-REAP APs registers without any problems at the backup WLC and switches back successfully to the primary controller after recovering from reboot. Unfortunately the WLANs 180,181,190,191 show status "DISABLED" every time the primary controller comes back and I have to enable them manually.
Doing exactly the same procedure with one of the other WLC, running AIR-CT5500-K9-7-0-116-0, I never face this problem.
View 5 Replies
ADVERTISEMENT
Sep 3, 2012
I didn't design the job, but is pretty straight forward, except the following, the design has a single wlc 5508 with 2 physical connection between two non cisco switches. There are 2 initial WLANs to be created. I am ok with most of the wlc config execpt the following:
Now from my understanding of everything I have read recently, you can't use LAG on the 2 physical connections if they connect to 2 seperate switches, unless, although not offically supported, the 2 connections are on either 2 3750s in the same stack or a pair of 6500s running VSS. So I believe that in my case 2 seperate connections from the wlc to 2 non cisco switches will not work with LAG. Is my understanding of this correct?
Is there a way to maintain the 2 physical connections from the wlc to the 2 non cisco switches to maintain redundancy?The wlc will have a management interface obviously, but from what I have read, the 2 WLANs that are going to be created have to have their own interface on the WLC. Which I understand as the managment int and each of the 2 WLANs are on different subnets.
If I don't use a single uplink to one of the non cisco switches (either 1 or 2 physical connections) using LAG, it appears to me that each of the interfaces ( management, wlan1 and wlan2) need to have a physical connection from the WLC to the switch, with each interface mapped to a physical port on the WLC, so correct me please if I am wrong, but this would mean I need 3 physical connections between the wlc and the swtich?
View 3 Replies
View Related
Jan 2, 2013
We created a VLAN interface and a WLAN on the wireless controller (5508) and using it for Guest Wireless (Web auth), can we use the same VLAN and WLAN s for Wired Guests also?
View 5 Replies
View Related
Jan 25, 2011
I am using Cisco Wireless LAN software revision 7 on an AIR5508. I am sure that I read somewhere that the controller will not allow 2 w lans to talk to each other but trawling back through my books I can't find the information again. Essentially, I am looking to find out if there is a feature (other than on the default gateway which is a layer 3 switch) that will say that if WLAN1 tries to talk to WLAN2 via the default gateway, the controller will not allow it.
I remember from what I read that I think this is the case but just cant find where I read it.
View 2 Replies
View Related
Aug 5, 2011
I have acer laptop with xp and must do enable my lan card to open conection in devices manager.every reboot the lan conection is disabled.for information I delete a virus pum bad proxy with malwarebytes before I have a problem know ervery thing is ok without virus.
View 6 Replies
View Related
May 2, 2013
One week ago I use a WLC 5508 to place and replace another WLC 5508 with version 6.0.199.4, when I conect the new WLC all AP´s works OK only 10 dont work and not are recognizes from the WLC with version 7.3.101.0. The fail is the radios stay disabled. All ap´s are AIR-AP1242G-AK9 . See the image below, the only difference this ten AP´s are conected in switches cisco all the rest are connected in switches of ohter vendor. If possible some command in the configuration is not neccesary and make the bad function?This is tipically config apllied by the customer in they cisco switches interface GigabitEthernet0/22description PB-RS-A22switchport access vlan 5switchport mode accessswitchport port-securityswitchport port-security aging time 2switchport port-security violation restrictswitchport port-security aging type inactivitymacro description cisco-desktopspanning-tree portfastspanning-tree bpduguard enable?
View 4 Replies
View Related
Apr 10, 2013
get a installed certificate work on a 5508 WLC Controller without rebooting. Is there a way? Is it possible to just reload a process to get the certificate work?
View 1 Replies
View Related
Jan 14, 2013
We have a 5508 controller in main site.Which has two ports connected to local network.Management VLAN 500 is untagged and mapped to Port 1.All other interfaces are including 501 to 507 are mapped to Port 2.We have a SSID that is mapped to VLAN 501 interface , which successfully can be joined in main site.We connect an AP to remote site ;We have a remote site VLAN 115 which can be reached from main site.We connect an AP to access vlan 115 port on the remote site , we had described option 43 , so AP can successfully finds controller in local mode.
AP gets ip from VLAN 115 , can setup connection / ping controller successfully.There is a wide area connection between remote and main site.No trunk setup , the whole remote site is vlan 115.However when the client is trying to connect the test SSID , client cant get connected nor get ip address.Local switching is disabled.For this setup , client comes to AP as a requested , AP tunnels traffic to controller from vlan 500 , controller lets the client get into wired platform from VLAN 501.
View 25 Replies
View Related
Jan 25, 2012
We have some AP keep on disassociating. All together we have 21 APs in the building but only this 7 APs keep on disassociating in every hours.
Below is the log i grab from our 5508 controller.
Last reset reason: operator changed 11g mode
Our controller code is 7.0.116.
View 16 Replies
View Related
May 29, 2013
After reboot WLC , the switch port was err-disable , the cause is link flap after we reboot 3 times , the switch port link flap err-disable every time? We don't know why the WLC rebboot will cause it , it just normal action on device the WLC version is 7.4.100.0 link switch with access port , no port channel , no portfast.
View 11 Replies
View Related
Dec 13, 2011
we have the issue that a new WLC 5508 has been installed in a new location. Unfortunaltelly we have no hands-on suopport on-site, so just remote connection.Now we figured that the service-port and management interfaces have to be reconfigured. In case we can not reach the WLC with the new configured interfaces it would be useful if the WLC reboots automatically after time x to reload the previouse working configuration.So the question is, is there a functionality to create a script which reboots the WLC automatically after time x?
View 4 Replies
View Related
Feb 15, 2013
I have a WLC 2106 which is configured and working as follows: [code] how do i get the AP at Site B to use the local server (10.0.28.x) to hand out DHCP leases?
View 3 Replies
View Related
Sep 7, 2011
What is the maximum number of WLANs/SSIDs that can be configured on a H-REAP access point? I have a network with 3502i AP's, centralised WLC's in the data centre running 7.0.116.0, and WCS version 7.0.172.0.
I was successfully running 2 SSID's at a remote site, one SSID was configured for H-REAP local switching, dropping out to the local site VLAN X, and the other SSID was a central switching guest WLAN anchored to a WLC in a DMZ.I configured a third SSID at the local site running H-REAP local switching, and now I cannot see the guest SSID anymore, it does not appear to be broadcasting.Is there a maximum of 2 WLANs/SSIDs when operating in H-REAP mode?
View 5 Replies
View Related
Sep 7, 2011
I would like to create multi-WLAN for personal communications, and gaming purposes. Each WLAN (is located in seperate house) and consists of a wireless AP wirely- connected to wireless router. The computers in each of these WLANs are connected wirelessly to the router. The houses (containing the WLANs) are locates within the region of a central wireless internet AP tower antenna.
I managed to utilize this central AP to make the connection, and make multiplayer gaming on two computers (in different houses and without using the internet services), each computer is connected to the central AP by a USB witrless adapter.My question is what are the necessary configurations that I need to make on the routers and APs? I have a number of different TP-Link routers (wr1043, wr743, wr543), micronet APs. Wr743 and 543 have AP client mode that can be used to simultaneously connecting wirelessly to central AP and to attaced computers.
View 2 Replies
View Related
Aug 2, 2012
There are 8 existing W LAN's in our WISM controller & it is working fine without any problem. Now the problem is any new W LAN's are not broadcasting from WISM to APs, I am able to create & enable it in WLC but it these W LAN's are not reflecting in associated APs.
FYI: WISM controller is in 6500 switch & FWSM module also in the same switch, earlier there was rule with any any traffic in the FWSM but recently we have removed the FWSM & all rules moved to checkpoint. We have check the in firewall there is traffic is blocking.
View 18 Replies
View Related
Jun 7, 2011
I want to run 2 separate wireless networks from the same appliance (Linksys E2000). Not just separate BSIDs or SSIDs, I want to run an N-only AP and a G-only AP. My wife's laptop is the only wireless N device and I want to ensure that she's getting true wireless N speeds. From what I could tell, I could set up a different VLAN for 2 separate WLANs, but they'll both still both follow the 1 wireless standard (either G or N). Is this even possible or do I need to run two separate wireless APs?
View 4 Replies
View Related
Feb 16, 2013
We have inherited a 5508 controller running 7.0 code and WCS running 7.0 code. This site did not have a backup controller. So we have installed a wism as a backup controller. The problem is no one can seem to remember the pre shared keys for the wlans on the primary controller. Can I use WCS to duplicate the wlans to the secondary controller and have the psk copied?
View 3 Replies
View Related
Sep 25, 2012
when I try to enable a WLAN that is using the same SSID as another WLAN I get this message
The following errors occurred while updating the WLAN:
WLAN with duplicate SSID and L2 security policy found.
each location has its own interface because each site is setup on our 6509 with a different VLAN. What is the best way to work around this.
View 10 Replies
View Related
Jul 29, 2012
I have intel centrino n 2230 wireless card in my alienware M17X-R4. When I search for available WLANs I can see all 2.4 GHz networks but none 5 GHz.
I have Netgear WNDR3800 AP running openwrt backfire 10.03.1
settings for the AP are:
mode:802.11 a+n
HT mode: 20 Mhz
Channel: 40 (5.200 GHz)
i tried several config alternatives - no joy
i updated the driver of the intel wifi card to the latest - no joy.
View 5 Replies
View Related
Jan 19, 2012
ive got some problems with my HP pavilion dv6000...i have recently reinstalled pc with windows xp home edition..installed drivers recommended on the HP official webpage and in HP wireless assistent still states that Wireless and bluetooth is disabled..but in device manager is enabled. also with my audio driver .already installed but dont make any sound.
View 2 Replies
View Related
Nov 5, 2012
I'm configuring AIR-CAP2602I-E-K9 out of the box, literally, and I want to configure it with a static address. I paste in the following commands. [code]After the host name line is pasted in I get "ERROR!!! Command is disabled" but the rest of the commands are accepted. I do a sh capwap ip config and the get the output below which looks like that config has been taken but why not my hostname? [code] I know or hoping that the APs will contact the wireless controller since I've the ip in there for it. It just means I'll be renaming all the APs, all 18 of them!
View 6 Replies
View Related
Dec 28, 2011
Currently Being Moderated Wireless users getting disabled
View 6 Replies
View Related
Jan 28, 2011
I tryed going into bios and disabled it and reabled it still its not working, tryed to uninstall it and reinstalled it still not working
View 1 Replies
View Related
Feb 16, 2013
I have a westell DSL modem/router supplied by Frontier. It connects only to the telephone line and via cat5 to my main router, a cisco EA6500. Everything seems to be working fine, I just would like to understand a few things.I disabled wireless radio on the westell, enabled it on the cisco, so I have just one WIFI network active.I know I am not supposed to have two DHCP servers active, but I did not know how else to be sure the CISCO would get a good address, so I left DHCP active on the WESTELL, and also enabled it on the CISCO to provide service for the rest of the net.The WESTELL admin interface is at 192.168.1.1, and assigns addresses in this range.According to the WESTELL, the CISCO is at 192.168.1.27, which I assume was assigned by DHCP.The CISCO has an admin interface at 10.144.224.224, and assigns addresses in this range to all the other devices on my net.As I say, everything works.I can access both router admin pages with a browser on my main 10.144.224 network, and can ping both.But I don't understand why it works.What rules allow me to talk to the WESTELL admin page from the CISCO private network, but do NOT propagate the DHCP access which is at the exact same IP address.
It is great that it works. But should I really have disabled DHCP on the WESTELL and assigned a static address to the CISCO? Or is this situation actually provided for in the rules, not just a lucky accident that it works?Why does the scanner say that the CISCO DHCP is "Unknown" rather than Authorized or Unauthorized? Is there something I can or should do to get it to be "Authorized"? I can ping 192.168.1.1, but not the 192.168.1.27 (times out), and yet when I ping a non-existent 192.169.1.3 I get "Reply from 192.168.1.27: Destination host unreachable".
View 4 Replies
View Related
Apr 17, 2011
my laptop can't connect to a wireless network, so I have to keep it in one room connected to the modem. When I unplug it, even with the wireless switch on, it loses the connection. When I use ConfigFree, it says the wireless network device is disabled. I went to device manager and updated the driver for the network adapter, and it still said it was disabled. What should I do now?
View 6 Replies
View Related
Sep 26, 2012
I connected AP 1522 to AC power source and this is the message that i received on the console port.
%CDP_PD-2-POWER_LOW: All radios disabled - AC_ADAPTOR (0000.0000.0000)
Why this message apear ?This is not sufficient power to bring up radio interfaces?
View 5 Replies
View Related
Jul 6, 2005
When I view web page of 1410 radio is show ethernet enabled and up but radio as disabled and down. I have tried to enable but to no avail. Is this a sign my radio has gone bad?
View 3 Replies
View Related
Dec 27, 2012
On my Toshiba A105, the wireless adapter (Intel PRO/Wireless 3945ABG) is disabled. When I ask it to be Enabled, it goes through the motions but then immediately disables it again.
View 2 Replies
View Related
Feb 15, 2011
I have a windows 7 laptop and when I connect it the a wired connection it disables the wireless & 3G connections, but when I unplug the cable it doesn't renable the connections, I have to go into the network connections and select each one and renable it again.
View 6 Replies
View Related
Sep 14, 2012
I have an ASUS G71gx laptop with Windows Vista 64 bit. I noticed upon start up my wireless connection would not automatically connect. I hit diagnose and repair, and it stated that I did not have wireless connectivity turned on. I tried flipping the wireless switch on and off a few times to no avail. When I would turn it on and off, the blue LED light was OFF. Also, each time I switched it on and off, it said on the screen that the wireless LAN adapter was OFF (even if the switch was turned on). Then, I restarted the windows explorer bar a few times as well as flip the switch again. This time, the blue LED turned ON. However, the internet was still turned off. I hit diagnose and repair again and it said the same thing as previously stated. It gave me the option to repair it by turning on wireless compatibility/connectivity, so I hit that. After that it turned on and I could use it with no problem.
View 3 Replies
View Related
Oct 1, 2011
ok i got a toshiba a15-s129 and yet its not enabled the wifi .. the light is amber and i got the module drivers and the function keys .. i hit the function + f8 yet nothing and i also have the software for atheros and yet it says wireless network interface disabled? any clue on how to enable this wireless or how to disable the hotkeys so it will not find any settings for it ...?
View 1 Replies
View Related
Jul 28, 2011
I cannot connect to the internet on my laptop using wireless. It was working fine for a while and it just stopped. This is not the first time this has happened. Although i cannot remember if i caused it to start working again. My laptop wireless hardware has disabled itself. I've tried enabling/disabling and troubleshooting from what i know how to do but its still not working. This problem started yesterday.
Tech Support Guy System Info Utility version 1.0.0.1
OS Version: Microsoft Windows 7 Home Premium , Service Pack 1, 64 bit
Processor: Pentium(R) Dual-Core CPU T4300 @ 2.10GHz, Intel64 Family 6 Model
[Code].....
View 12 Replies
View Related
May 5, 2012
how i can have internet connection again. here's what happened, i disabled the Broadcasting SSID and the after that my devices can no longer locate the wifi, and then when i cant configure the setting back to its original settings because i cannot establish a connection with the mf30 and my laptop eventhough it's via USB.
View 1 Replies
View Related
