Cisco Routers :: WRVS4000 With Static IP - Required Modem Settings
Apr 16, 2013
I had an WRVS4400 (but didn't use the wireless), it it died. I'm replacing with an RVS4000. I have all the settings from the prior router, but my question has to do with the DSL modem in use in conjunction with the router, because (in my absence) my wife had a conversation with SBC, trying to use the hook to the modem directly and ended up altering settings on the modem that may affect the RVS4000 when I go to install it upon its receipt from Amazon tomorrow.
We have a business that uses a third party software vendor's website; their servers access our data on our server behind the router. So we use a static IP address, and port forwarding. No problem there. But I could have sworn that, with the WRVS4400 we used to have the modem configured as bridged; as of this morning, the modem shows PPPoE, and my wife can't recall what SBC had her do in that regard!
So, for the situation I've described, should I put the modem into bridge mode (and porting it into the RVS4000). Like I said, we have a static WAN IP address, and a range of more static IP addresses.
View 1 Replies
ADVERTISEMENT
Jan 20, 2013
Recently switched DSL providers and now have Cisco modem DPC3008. Able to connect to internet directly thru modem. Able to connect wired or wireless to router. Unable to get router to connect to internet via modem. Tried restart, reset, and new set-up. Called ISP (Charter) - no way, said contact Belkin.
View 2 Replies
View Related
Feb 20, 2012
We have 2 sites with 2 internet connections at each site. All are SRP527w routers. 1 is for internet and 1 is for a site to site VPN as,Currently we are using Static Routes on the PC's so they can access each server no matter what site they are at. I have looked at using the Static Routes section on the SRP's but cannot get it to work.
View 2 Replies
View Related
Aug 18, 2011
I just got my first WRVS4400N v2.Nothing has changed, the definition of small business means there are USUALLY one office, and several people runs around thus the need of a VPN server sitting at the home office Router. I think most of us small business operators had wished for a connection away from office, NO REMOTE GROUPS, just clients on phone, or laptop. Using this connection to get to some files which isn't sitting in the cloud, or perhaps using it to hop over firewall restrictions that some overseas countries had imposed.
What you should have is a setting for Stand-alone VPN server, NOT Router to Router.. What you should have is feature that generates the various psk for different platforms. What you should have is made things simple, instead of these magicabbage which goes no where for the small businesses.Through out this thread the original poster is presenting the same problem, he and I don't have a Remote Group router to enter an IP address, tell us to use the QuikVPN client DON'T work, the Server isn't UP to begin with!Moreover, the VPN client installer on the this new v2 runs only in Win 2000 or XP??? What the (*&^! Doesn't seem like a large business like Cisco should have in their boxes.
View 1 Replies
View Related
Feb 16, 2012
My adolescent son wants to create a server to host video games. We, the parents, want to separate our computers and files from all the crazy security risks my son and his friends take, while allowing them to learn by their mistakes.I want 2 separate networks, or does this make sense? Would love to have our computers (assorted PC's, Macs, both laptops and desktops, running Vista Ultimate, Windows 7, OSX 10.5 and up), ipods, TV's, Blu-rays, wireless printers, etc. isolated from our son's computers, ipods, TV's, XBox, Blurays, wireless printers, (as well as the digital stuff his friends bring over).Since security is the reason for this, would love any tips over and above Brian Posey's article on Tech Republic (5 common security mistakes people make on setting up wireless networks, or something like that)We have Optimum high speed (testing up to 65 mps) internet service and 5 static IP addresses to work with.
View 4 Replies
View Related
Oct 5, 2011
Does the following setting is a shipping default in the ACS 5.1?,In the Access Policies ->Network Device Admin -> Identity -> Advanced Options, the If user not found was set to “Continue” .
View 6 Replies
View Related
Feb 27, 2012
I have a 5505 configured with a active/standby dual wan setup using the sla tracked connection settings. Is there a way to configure the ASA to stay on the backup connection after activating? We had a situation where the main T1 was bouncing, so the backup connection was being activated and deactivated very often. The problem is that there is an app being used that does not allow users to reconnect to dropped connections immediately, so every time the asa switches wan connections it causes a significant disruption.I should note that I already set monitor options frequency to 240 seconds. I could set it higher, but then we have a longer delay when the main connection dies.
View 2 Replies
View Related
Mar 10, 2012
I got a project where I have to provide NATTED addresses to customers for the internal servers and I found out that the outside address range /27 already in use. We are using 5510 with ver 8.1. We cant use PAT here. Any other option to accomplish this task.
View 1 Replies
View Related
Mar 10, 2012
I got a project where I have to provide NATTED addresses to cutomers for the internal servers and I found out that the outside address range /27 already in use. We are using 5510 with ver 8.1. We cant use PAT here.
View 1 Replies
View Related
Oct 2, 2010
I have the dir-601 as my main router. Its IP settings are dynamic, not static. My second router, the router I'd like to use as the access point is a Belkin Wireless G Mimo. My goal is to setup the Belkin as an access point downstairs away from the main router. I'd like to do this wirelessly. I'd like to phsycialy plug devices into the Belkin, while the Belkin receives access to the internet wirelessly from my main router, the dir-601.
Here's my issue. There's an easy option to use the Belkin as an access point. So I do this and set the Belkin router to an IP outside the DCHP range ( currently 192.168.0.100 - 192.168.0.199 ) to 192.168.0.250. My dir-601 will only recognize the Belkin access point while plugged in physically. I know this because when I did a ping test it only see's the Belkin when plugged into the dir-601 via ethernet cables. My ultimate goal is to simply set the dlink dir-601 to recognize the Belkin as an access point.
View 7 Replies
View Related
Mar 12, 2013
Today I installed the 1.0.2.6 Firmware on a RV180W. I only have now two problems regarding the Static DHCP support in the GUI.
1. Via the Networking > LAN (Local Network) > Static DHCP I have no buttons to Add a new static Lease.
2. Via the Networking > LAN (Local Network) > DHCP Lease Clients I can thick a Lease and click on Make Static IP. The result is an error: Operation failed.
View 3 Replies
View Related
Jun 28, 2012
How do I change my cisco wireless from a dynamic setting to a static settings.
View 1 Replies
View Related
Jan 23, 2011
I have a laptop that travels alot to different networks. I go to two differnent networks where I need to enter static network settings (wireless nic). How the heck do you save these settings so I don't have to enter them all the time. I know you can save the network profiles but does this save static settings assigned to the wireless nic?
View 3 Replies
View Related
Jul 3, 2011
Is there an alternate way to get the DNS settings off of the router? I've followed all of the steps up above, but I cannot set up a static IP Address on my computer without knowing the routers DNS settings, which I cannot retrieve from the web-based setup due to the corrupt firmware.
View 2 Replies
View Related
Oct 15, 2012
I recently upgraded to the EA4500 and the only issue I'm having is that it will not recognize my static DNS settings, which worked fine on my older E2000. No other hardware has changed except the router.I've tried both Google DNS and OpenDNS. In either case, the DNS settings can be entered and saved in the Basic Settings tab, but when I go to the admin tab, it shows my ISP's deafult DNS.
View 4 Replies
View Related
Feb 27, 2012
I am trying to setup my Internet connection on my linksys E1200 router using static IP settings below -I am getting following error when trying to do this. These are the IP settings provided to me and are configured on my laptop to connect to my ISP as well.
View 6 Replies
View Related
Nov 11, 2011
I forgot password for my modem settings. I changed the default 'admin' 'password' for security reasons but now I forgot it.Without it I couldn't even change WEP Key to connect wireless. I'm using Compex WRL254G All in One Router/Modem.
View 6 Replies
View Related
Aug 15, 2011
i just recently upgraded to Road Runner Extreme which Uses DOCSIS 3.0 SBG6580 Modem and i was wondering what internal settings i should use to maximize my speeds and online gameplay. I'm running a Ethernet line into my Xbox360 and wireless for my laptop. Also, i was told that Road Runner Extreme would get me 35Mbps downstream and 5Mbps Upstream, yet these are the speed test's i'm getting [URL]
View 1 Replies
View Related
Mar 3, 2013
I currently have a pc, iMac, PS3, a win7 laptop, 3 phones in the household.Till very recently i have been using a dlink dir615 wireless router as i had a wimax connection.I have changed ISPs and now have to get internet through a ADSL modem..i have just bought a Dlink N300 ADSL2+ modem...i need to have all settings exactly the same (or with minimum hassles) to change over the connections.getting all the devices to handshake on the network especially the mac and pc was not the easiest thing so i don't really fancy doing it again...
View 14 Replies
View Related
Oct 8, 2011
Got a Belkin wireless modem router some 18 monthes ago, and after a bit of a struggle managed to set it up. It worked fine, aside from the odd depower repower. For some reason, it just stopped working yesterday. I initially checked all my cabling etc and everything seems fine. I next tried resetting my modem/router to factory settings. When I tried to install the Belkin software I fell at the first hurdle with a message saying "The setup assistant is not able to connect to the router". After googling my issue, I followed others advice and running the cmd setting and typing in "ipconfig" only to find that my media state was disconnected.
View 2 Replies
View Related
Apr 3, 2013
Is there a guide to setup a VPN connection using this router? I've follow the setup guide provided by cisco but I'm having issues. When attempting to connect using the quick vpn client, I get error messages.
View 1 Replies
View Related
Mar 11, 2013
need The Firmware for the device....URL
View 5 Replies
View Related
Jan 2, 2012
I have a RV042 and I want to tell it to allow certain IPs to use WAN1 and others to use WAN2. How do I do this ?
View 3 Replies
View Related
May 15, 2011
I try to change modem speed from 1200 to 19200 on aux 0 interface.But I can't save the settings using "write memory" In show running-config, I can see modem speed successfully changed.
Cisco3825's OS information is here. c3825-spservicesk9-mz.124-25b.bin
View 3 Replies
View Related
Mar 31, 2012
can i connect to internet without settings in modem is dat possible?
View 3 Replies
View Related
Feb 5, 2012
I've a Shiro DSL805E Modem and to connect to multiple computers, I connected an Encore 5 Port Switch. Now I got laptop and thought of getting a wireless network, so I bought TP-Link TL-MR3420 Wireless Router and connected it to the one of the wires from the Encore Switch. But I'm unable to access the internet through TP-Link Router but the internet works fine for the computers which are directly connected to switch. how to do ip settings for TP-Link Router. But when I connect router directly to modem by bypassing switch, it works fine but not via switch. I have some restrictions due to which I have to strictly following this sort of connection: Modem -Switch - Router
View 1 Replies
View Related
Jan 6, 2012
I am very new to port forwarding and firewall issues. I have been told that the software issue that I have probably is a router/modem issue as every other possibility has been ruled out. I have a Westell 7500 modem. How do I access, set or change settings on it? And, which is the better modem, a Westell 7500 or a Westell 327W??
View 1 Replies
View Related
Jun 12, 2012
RV082 configured for Dual WAN [Code]....
(2) identical DSL connections, configured as Static IP (not PPPoE) with modems in bridged mode. Static IP's are /25 subnet and same gateway ** this may be a problem? Dual WAN set for Load Balance, network service detection is OFF
We have a 2003 terminal server running and successfully receiving connections through both WAN connections. Depending on location, half the users are connecting to WAN1 IP and the other half to WAN2 IP. We are getting sporadic disconnects of the remote users when they are idle for a couple minutes and automatic reconnection of the session takes over a minute. If they close the (locked up) session and reconnect manually it will let them in right away.
Could the handling of the Dual-WAN be the culprit? Could the same gateway for both WAN's create this issue upstream (out of my control)?I am going to move everyone to connecting through WAN1 and then change to Smart Link Backup and see if the issues persist.
Another thought is to use a secondary IP on the terminal server and use Protocol Binding to match "All traffic" for IP1 to WAN1 and IP2 to WAN2, which theoretically would stabilize the situation?
View 36 Replies
View Related
Jun 26, 2012
I installed an IP camera, and had to change my E1000 router settings to a static IP address. Now I can't access the router settings. 192.168.1.1 is still the default gateway, but it won't open in any browser.
I'm reluctant to do a reset because it took me quite a while to figure out how to get the IP camera and port forwarding working (it does!), and I'd hate to do it all again and come to the same place. I'm not very good at this stuff, and it's a small miracle that I did it once.
View 4 Replies
View Related
Feb 26, 2013
We have a Comcast business class cable modem with a static IP address. There are two devices hardwired to it; a server and a Linksys WRT610N, The server is hardwired to it with port forwarding set for ports 21, 80 and 5900. It works perfectly and can be reached as intended by the outside world but not by our own network. Our Linksys WRT610N is hardwired to the modem. All computers on the wireless network see each other and can access the internet perfectly. So all seems well enough. BUT, no computer on our network can reach our server. Using the domain name or VNC connections from inside our system results in time outs and no connection.
View 12 Replies
View Related
Sep 23, 2011
I have a Pix 501 running 6.3 code sitting behind a cable modem. I use ip address outside dhcp setroute because I don't have a dedicated IP from my cable provider.
How do I configure the Pix to host VPN connections from my iPad when offsite? Since the outside interface is going to change, I can't configure a static IP.
View 1 Replies
View Related
May 8, 2013
i lost my belkin n150 installation cd, and i haven't installed it on my computer, my net connection to my computer via lan keeps dying, but wi-fi works perfectly. What should i do? Where can i download the software from??
View 1 Replies
View Related
Feb 27, 2013
I have DSL service with AT&T and I have a Motorola 3360 modem. We also have a /28 network of static IPs from AT&T. When I login using PPPoE on the modem it gets x.x.x.190 as it's address. Our range is 177-190. I have two ASA 5510s in an active/passive failover configuration with the Ethernet port of the modem and one interface of each of the ASAs on a dumb layer 2 switch.
I want to setup this DSL connection as a backup to our main Internet connection. I cannot figure out what setting on the DSL modem to use to make this happen. I know I cannot use PPPoE in a failover setting so I can't have the modem in bridged mode. There is some mode where it passes the 190 address to the connected device and when I plug in a PC directly to the modem and set it for DHCP it does get 190 as it's address. So do I configure the ASA interface as 190 with one of the other addresses as it's standby? What do I set my route on the ASA to for use of this connection? Can I then make use of these other static addresses when plugging other devices into the layer 2 switch?
View 4 Replies
View Related
