Cisco AAA/Identity/Nac :: ACS 5.1 Default Settings Required

Oct 5, 2011

Does the following setting is a shipping default in the ACS 5.1?,In the Access Policies ->Network Device Admin -> Identity -> Advanced Options, the If user not found was set to “Continue” .

View 6 Replies


ADVERTISEMENT

Cisco Firewall :: ASA 5505 Dual WAN Settings Required

Feb 27, 2012

I have a 5505 configured with a active/standby dual wan setup using the sla tracked connection settings. Is there a way to configure the ASA to stay on the backup connection after activating? We had a situation where the main T1 was bouncing, so the backup connection was being activated and deactivated very often. The problem is that there is an app being used that does not allow users to reconnect to dropped connections immediately, so every time the asa switches wan connections it causes a significant disruption.I should note that I already set monitor options frequency to 240 seconds. I could set it higher, but then we have a longer delay when the main connection dies.

View 2 Replies View Related

Cisco Routers :: WRVS4000 With Static IP - Required Modem Settings

Apr 16, 2013

I had an WRVS4400 (but didn't use the wireless), it it died. I'm replacing with an RVS4000. I have all the settings from the prior router, but my question has to do with the DSL modem in use in conjunction with the router, because (in my absence) my wife had a conversation with SBC, trying to use the hook to the modem directly and ended up altering settings on the modem that may affect the RVS4000 when I go to install it upon its receipt from Amazon tomorrow.
 
We have a business that uses a third party software vendor's website; their servers access our data on our server behind the router.  So we use a static IP address, and port forwarding. No problem there. But I could have sworn that, with the WRVS4400 we used to have the modem configured as bridged; as of this morning, the modem shows PPPoE, and my wife can't recall what SBC had her do in that regard!
 
So, for the situation I've described, should I put the modem into bridge mode (and porting it into the RVS4000). Like I said, we have a static WAN IP address, and a range of more static IP addresses. 

View 1 Replies View Related

Belkin Routers :: N750 Required Settings For Cisco DPC3008 Modem

Jan 20, 2013

Recently switched DSL providers and now have Cisco modem DPC3008. Able to connect to internet directly thru modem. Able to connect wired or wireless to router. Unable to get router to connect to internet via modem. Tried restart, reset, and new set-up. Called ISP (Charter) - no way, said contact Belkin.

View 2 Replies View Related

Cisco AAA/Identity/Nac :: ACS 5.3 Reports Required

Jul 2, 2012

I have modified my radius accounting reports using "interactive viewer"  and saved successfully but the exported report doesn't reflect these changes. I'm just wondering what's the point of being able to modify the reports if you can't export your changes or there is something I'm missing?

View 3 Replies View Related

Cisco Switches :: How To Set SG200-08P To Factory Default Settings

Oct 18, 2011

We need to "reset" a SG200-08P switch back to the factory default settings and noted the "Quick Start Guide" implies the "Reset" button next to the power button doesn't exist and refers the user to the "Cisco Small Business Smart Switch Administration Guide" for instructions.  We couldn't find any information related to a "factory reset" in that document either.  Pressed the "paper clip button" on the switch but we still can't get in. 

View 7 Replies View Related

Cisco Application :: To Restore The Default Settings Ace 4710

May 22, 2013

the ACE 4710 is running 3.2.5 and I need to put it in another environment.Is there a way to reset its settings?

View 3 Replies View Related

Cisco Routers :: WRVS4400N Resetting Itself To Default Settings?

Feb 20, 2012

I have 2 WRVS4400N routers that were installed at 2 remote locations to provide VPN access to these sites. The routers have been found reset to the factory defaults on three occasions, twice on one of them and once on the other. Both sites are unmanned so no-one is on site to have pressed the reset button, and both routers were set to have remote management disabled. They are running v2013 firmware.

View 3 Replies View Related

Cisco Switching/Routing :: 6509 LAN Is Set Up With Default VTP Settings

Dec 2, 2012

my LAN is set up with default VTP settings
 
-core switch cisco 6509 vtp server
-access switches 2960 vtp server
-no vtp domain set on any switches
-no vtp password set
 
untill now i manually set the vlans on switches (didnt see anything  automatic created on switches)is there any danger with the above settings , that a switch with domain name set and higher revision numberwill delete my vlan settings? if yes how can i protect/disable vtp in my LAN

View 11 Replies View Related

Netgear WNR2000 - Change Default Settings?

Jun 1, 2011

How do I personalize the settings on my router from default. Netgear wnr2000.

View 2 Replies View Related

D-Link DIR-825 :: Magically Reverts To Default Settings

Dec 19, 2011

What would cause my Dir-825 to magically revert to it's default settings?  This is the 4th time this has happened.We rely on a Verizon Network Extender for phone service.  It requires an internet connection to function.  When the router brain-farts, we don't have phone service... and we don't know it until we try to call out, or try to use the internet. We went to bed last night with the router working and woke up to it not working.  It's just my wife and I here.  I haven't seen the dog showing any interest in jacking with our computer gear.

When I access the setup utility and go to Manual Wireless Network Setup, the Wireless Network Name has defaulted to dlink, and Security Mode is None.  I have to re-enter my personalized setup info, (because that is what our computers are looking for), then all works fine again.I'm a savy XP user,  my wife has Vista (yuk) (she doesn't know any better; her daughter installed it).We are Comcast customers.  We own a Linksys CM-100 modem.  (When I connect direct by hardwire, (i.e. bypass the Dir-825 router), from the modem to any computer, or the Verizon Network Extender, they function just fine. Setup utility for Dir-825 says we have Hardware Version B-1; Firmware Version 2.02NA.

Set Firewall settings to Endpoint Independent for TCP and UDP. I see other posts addressing similar issues of reversion to default settings... but there don't seem to be any clear resolutions of these issues. On 2010-03-11, gunrunnerjohn posted, "I think there may be a shadow file that's actually in the FLASH that needs to get written back to make the changes stick.  I seem to recall there is a command to sync the RAMDISK copies to the FLASH."  Yet there is no more to this thread. 

View 3 Replies View Related

Cisco AAA/Identity/Nac :: ACS 5.1 Why So Much Disk Space Required

Apr 7, 2010

We are getting ready to bring up 2 new 5.1 ACS servers to replace our ACS 4.2 configuration.The documentation says that 512GB of disk space is required for each server.  This means we will need to request1 TB of disk space.  The VMware folks in our group are asking why we need so much space when the 4.2 servers are only using 20 gigs including the OS.

View 3 Replies View Related

Cisco AAA/Identity/Nac :: ACS 5.2 Access Service Required

Oct 30, 2012

We are using ACS 5.2 in our Network. As can be seen in the provided figure, nothing in the Access Services can be displayed properly.

View 4 Replies View Related

Cisco Routers :: RVS4000 Necessary To Reset To Factory Default Settings

Feb 15, 2009

Recently purchased a RVS4000 Router, which included v1.1.14 firmware. Is it necessary to reset the router to Factory Default settings, after upgrading to v1.2.11, as in most of the other previous upgrades?

View 37 Replies View Related

Cisco Firewall :: ASA 5540 / Time Settings To Default After Reboot

Feb 22, 2011

When i reboot asa 5540 firewall times settings to default

View 12 Replies View Related

Cisco Switching/Routing :: Restore Default Settings For SRW224G4

Mar 22, 2012

One of our costomers has a SRW224G4 Switch - which has not any documentation  :-(
 
I do not get onto the switch in any way.  I do not have an IP-Address, the default settings for he serial port do not work ... So I cannot reach the device and reset the password like described in: [URL]
 
Is there any other way to reset the device? I cannot find any reset button.

View 1 Replies View Related

Sharing :: Printers Switching Default Settings Automatic?

Mar 17, 2011

First time on this forum: I have a client running a Windows 2008 server, Windows 7 OS. We set the default printer as the server file cabinet printer, however, between logging off in the evening and back on in the morning the default printer switches to his local printer

View 2 Replies View Related

D-Link DIR-601 :: Upgrading Firmware From 1.0 To 1.02 Will It Default Factory Settings?

Aug 6, 2011

I currently have this router in use with verizon dsl (PPPoe) setup.I have this set to "always on". Since the verizon modem, which is also router has been set into bridge mode and the d-link came into play its been extremely slow, and dropping connection. The router is in a separate IP class, and has no conflict with the modem. My question is, if I upgrade this firmware from 1.0 to 1.02 will it default to factory settings? I know it says only some will. I do have the backup config file, but i would be doing this remotely, and would not be able to get to this router if it goes down. Has anyone gone from 1.0 to 1.2 and saw a difference and speed, and are you able to do this without losing settings.

View 3 Replies View Related

Cisco Security :: Can Set IP's 4260 Into Factory Default Settings With Single Command

Feb 20, 2012

Can we set ips 4260 into factory default settings with a single command?

View 0 Replies View Related

Cisco Routers :: WRVS4400N - Automatic Revert To Factory Default Settings?

Jan 23, 2013

I had something strange happen to my WRVS440N router yesterday. Our network had crashed for some reason. So I attempted to log into the device to see what was wrong and I was surprised to discover that all of the settings including user name and password had reverted back to factory default.
 
1. What are all of the possible scenarios that would cause this to happen?

2.Would disconnecting power in the middle of a boot up sequence cause the router to revert to factory settings?

View 1 Replies View Related

Linksys Wireless Router :: WRT320N Resets Wi-Fi Settings To Default?

Dec 1, 2011

My router automatically sets the wireless network settings to the original default. Sometimes after 1 hour sometimes after a week. It resets to automatic instead of the manulal settings I use for configuration. Changes the SSID to Linksys and disables wireless security.

View 5 Replies View Related

Cisco AAA/Identity/Nac :: Required Patch For ACS Appliance 1120 Version 4.2.15.3

May 4, 2011

Need URL for patch 4.2.1.15.3  with comptaible for cisco acs appliance 1120 . Though its for appliance patch should be along with webserver . I have downloaded patch of SE its not comptaible to this hardware .

View 4 Replies View Related

Cisco Switching/Routing :: 2960S - Default Queue / Buffer Settings When MLS QoS NOT Enabled

Feb 13, 2013

I have a customer that is seeing output drops on a 2960S with mls qos not enabled.  It appears that they are getting bursts traffic on the switch that is filling up the buffers, hence causing the drops.  I have a couple of questions:
 
1. What are the default queue/buffer settings when mls qos is NOT enabled on the switch.
2. Is there any good documentation out there regarding the buffer sizes of the different switch models
 
The customer is looking for an answer as to whether or not replacing the 2960S with a higher model would eliminate the output drops WITHOUT having to mess with QOS/buffer/drop threshold settings on the switch, and Cisco doesn't seem to make the buffer sizes readily available for the the smaller Catalyst switches.

View 1 Replies View Related

Slow Internet - Reset To Windows Default Settings Feature Which Does Not Work?

Jun 22, 2011

So just recently my Internet has been running a lot slower than normal at different times of the day (completely random, could be fine for hours then just turns slow). I know it's not the Internet itself, since it's only happening on my computer, and none others in the house - and I'm far from capped. I've run AVG, Spybot & Malwarebytes' scans and have found no infections of any kind. I've run TCP Optimizer and used the "reset to windows default settings" feature, which also hasn't worked one bit. I've tried different Ethernet cables and different plugs in the modem and no improvement.

View 8 Replies View Related

AAA/Identity/Nac :: ACS 5.3 Multiple Service Selection Required For RADIUS Wireless

Feb 26, 2013

I use ACS 5.3.0.40.8 with TACACS+ servicing Device AAA and RADIUS servicing the Cisco Wireless environment for AD user access. How can I implement 802.1x with the current RADIUS implementation with hindering current wireless users or am I hindered due to the EAP-GTC in use with PEAP via RADIUS?

View 3 Replies View Related

Linksys Wireless Router :: WRT54GL Randomly Resets Settings Back To Default?

Mar 18, 2012

I've had my WRT54GL for a couple of months now, and it keeps wiping my saved settings and reverting back to the default. It works fine with all devices for a week or so after the initial set-up, then will only work on the system that is wired.

View 1 Replies View Related

Linksys Wireless Router :: Reset WRT300N To Default Settings To Setup Internet Connection

Mar 29, 2012

I've just managed to reset the WRT 300N to default settings and have setup the internet connection etc and home network ... BUT no matter how I've fiddled with the wireless settings I cannot get any of the laptops or mobile phones to connect wireless to the network.The Windows software on the laptops 'finds' the router OK but for some reason the router seems unwilling to supply an IP address.I've checked ALL of the settings that I can think of, and all are correct ... well, all are exactly the same as my old router which worked perfectly.

View 4 Replies View Related

Cisco AAA/Identity/Nac :: ACS 5.3 Default Backup Password?

Aug 15, 2012

When doing a backup on any of the ACS 5.x appliances by default the backup is encrypted with PGP. What password is used for that? Is it configurable?

View 3 Replies View Related

Cisco AAA/Identity/Nac :: ACS 5.1 Password Rules Settings Per Internal User

Sep 27, 2010

I am looking for a way how to set the password-rules for individually for for some users or identity-groups.I just can find the global settings,Background of the requirement: We want to use password-aging for most admin-users, for some we dont want that pw expires.

View 10 Replies View Related

Cisco AAA/Identity/Nac :: ADSL Modem 867-K9 Not Connecting With Default Mtu

Feb 24, 2013

The ADSL Modem CISCO867-K9 is not connecting to our NAS router with default mtu value in the NAS router virtual template
 
Is there is any reason for ths ?  With the below settings my ADSL 867 connecting , but if i remove the (mtu 1440 and ip tcp adjust-mss 1392 , this modem is not connecting
 
My Virtual Template config
 
interface Virtual-Template1
mtu 1440
ip unnumbered Loopback3

[Code].....

View 1 Replies View Related

Cisco AAA/Identity/Nac :: ACS 1121 / 5.3 - Remote Database Settings In Monitoring And Reporting

Mar 26, 2012

I am configuring new ACS 1121 appliance with version 5.3 and wanted to know how to configure Remote Database settings in ACS5.3 Is that necessary to configure that option ?
 
Also one more thing I can see that ACS 5.3 generates lots of logs is there any solution to reduce such logs. It seems many unuseful logs which are system related are getting logged into device which might no be good for memory requirements of device.

View 6 Replies View Related

Cisco AAA/Identity/Nac :: 3650 - Radius Return Attribute To Set Duplex Settings?

Feb 28, 2012

I am doing 802.1X for a user on Cisco 3650 and wanted the Radius Server to return an attribute to set the Duplex setting of the port. with the correct Radius Return Attribute.

View 4 Replies View Related

Cisco AAA/Identity/Nac :: 7200 Default Network Access And CHAP

Feb 12, 2012

I am configuring some of my devices to use CHAP when their backup ISDN interface dials out to the 7200 concentrator node. I wan the CHAP requests to hit our ACS 5.2 appliances and be authenticated via this method. I have built a rule for 'Default netowrk access' which specifies these devices only however when I bring up the ISDN call the process fails. When I look at the logs it doesn't give an error reason but it does say that it failed on one of the rules in the 'default device admin' rule set.I even went to the bother of specifying a single IP address of one of the ISDN backup devices but the result is always the same.

View 3 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved