Cisco AAA/Identity/Nac :: 7200 Default Network Access And CHAP
Feb 12, 2012
I am configuring some of my devices to use CHAP when their backup ISDN interface dials out to the 7200 concentrator node. I wan the CHAP requests to hit our ACS 5.2 appliances and be authenticated via this method. I have built a rule for 'Default netowrk access' which specifies these devices only however when I bring up the ISDN call the process fails. When I look at the logs it doesn't give an error reason but it does say that it failed on one of the rules in the 'default device admin' rule set.I even went to the bother of specifying a single IP address of one of the ISDN backup devices but the result is always the same.
View 3 Replies
ADVERTISEMENT
Jun 10, 2013
when I click 'Create...' under Access Policies > Default Network Access > Authorization, and then press the 'OK' button, it says 'Please configure at least 1 condition.' However I have no way to configure conditions as the 'Conditions' text is just bold text and not a link or any sort of configurable area. If I go to 'Customize' on the bottom right and add conditions to the right list box, I still have no options when I press Create. Also, the 'green light' next to Default Network Access is grey with a line through it. This is the most cryptic system I have ever used
View 12 Replies
View Related
Jan 19, 2012
I have configured a Cisco 877 router to send RADIUS requests when a user logs in to the console (Line Console or Line VTY) using the following config:
aaa new-model
aaa authentication login default group radius
aaa authentication ppp default group radius
radius-server host 10.0.0.1 auth-port 1812 acct-port 1812 key mysharedkey
When I log the RADIUS packets I see that the Cisco router is sending the initial AccessRequest using PAP.
How can I configure the router to send it's inial AccessRequest packet using CHAP?
View 5 Replies
View Related
Jan 13, 2012
I've setup my ASA 5510 to use AAA to my Windows Server 2008 NAP. After many hours of troubleshooting I got my setup to work. The only thing I'm not satsified with at the moment is, that RADIUS is using PAP for communicating between ASA5510 and W2K8/NAP.I've tried ticking the box "Microsoft CHAPv2 Capable" box under Users/AAA => AAA Server Groups => Edit AAA Server.From EventViewer on W2K8/NAP I get Event ID 6278 and 6272., see attached filehow I change from the PAP to the CHAP protocol?
PS: ASA 5510 running ASA version 8.2(4) and ASDM version 6.3(5)
View 4 Replies
View Related
Jan 23, 2013
I´ve try to configure a VPN IPSEC between a Cisco 7200 and Juniper ISG2000.The tunnel looks like good but when a ping is sending, I´ve packets lost and getting the next error:IPSEC(epa_des_crypt): decrypted packet failed SA identity check.My configuration en both sites is the follow: [code] What is the possible problem here. mea be in the Cisco 7200 configuration or in ISG Configuraton??
View 4 Replies
View Related
Jun 6, 2012
I am trying to set up a PPTP VPN connection which also provides internet access. I have the following configuration. The router named "Router1" connects 2 computers PC1 and PC2 on the LAN side with a network address of 192.168.1.0/24. It is a PPTP server and a DHCP server. It gives IP addresses to PC1 and PC2. It has a static address of 192.169.1.2 on the LAN side and a static address of 10.2.9.1 on the WAN Side. PC3 has a static address of 10.2.9.2 and is connected to the WAN port of Router1. "Router2" is connected to the LAN side of Router1 and it has a static IP of 192.168.1.1. Router2 is connected to the internet and provides internet connection to PC1 and PC2. PC1 and PC2 connects fine to the internet and can see each other. However, PC3 cannot connect to the internet even though it is connected to Router1 by PPTP VPN connection. PC3 can see PC1, PC2, Router1 and Router2 but it cannot connect to the internet because Router1 does not give it the default gateway(192.168.1.1) to connect it.
When PC3 connects via PPTP, It receives a correct IP address(10.2.9.3), correct DNS addresses but the ip4 default gateway field is left blank, and the DHCP option is not enabled on connection properties of PC3. Router1 is a DD-WRT firmware router (DLink Dir 400) and has PPTP server enabled as a service. How do I get Router 1 to give PC3 a default gateway IP? And how do I forward all outgoing packets from Router 1 to Router 2? I do not need portforwarding for some ports, I need full access to the internet from PC3 though the PPTP connection via Router2
View 2 Replies
View Related
Dec 12, 2012
I am having some issues with creating an ACL for my gateway router.I want to block external access to my network 192.168.1.0/24 from internet so i set up the ACL on the WAN port of my 7200 router asI am using named extened access list -
{
deny ip any 192.168.1.0 0.0.0.255 log
permit ip any any
}
and i applied this inbound accesslist on the WAN port of router as
"ip access-group acl-in in"
Now i have blocked the external traffic to my network 192.168.1.0/24 but the issue i am having is i am also unable to reach outside now. All i want is to block external traffic on the router WAN port but allow internal traffic to outside. Did i miss anything in the access list?
View 5 Replies
View Related
Oct 10, 2012
I've got a 7200 vxr that I'm trying to create a named extended access-list in.
I got to configure it if I go into ip after that the only commands available for access-list are log-update, logging, and re sequence.
so if I go back to the main config menu access-list is an available command
but then from the main config menu, if I type: access-list extended eth0_in it says invalid input detected at the carrot marker which is under the first character of the work extended.
also, at the main config menu, if I type: ip access-list extended eth0_in it again give me the invalid input detected at the word extended.
I don't understand what I am missing to get this to work.
View 9 Replies
View Related
Apr 3, 2012
im having trauble when using chap as authentication for my two routers, i dont know whether my configuration is wrong or not.Is theres anything wrong with the configuration ??note : both routers are c2961
View 11 Replies
View Related
Jun 17, 2012
How the one-way hash is generated given the challenge number and shared secret password?It's just that I was reading Cisco 3 chapter 7, and it doesn't explicitly outline how the one-way hash is actually generated, it simply states that it is generated given the challenge number (randomly generated for every challenge message) and the shared secret password.
View 1 Replies
View Related
Dec 20, 2012
I'm trying to connect to ISP with PPPoE method using Cisco 861 equip. On the other side Cisco 3845 BRAS.Session fails at authentication phase. Authentication protocol chosen by routers is ms-chap-v2. Chap supported also. [code]
View 2 Replies
View Related
Feb 27, 2011
I found that TACACS should be available for network access with ACS 5.2:(url) But when I'm trying to create Rule tu allow PPP authentication against TACACS server I get error.
View 2 Replies
View Related
Oct 15, 2012
I have a question reguarding the Cisco Secure ACS 5.2 and network access vs device admin access. We have our switches,routers,and firewall configured to use TACACS+. We also have configured our Wireless LAN Controller to use RADIUS for allowing for 802.1X authentication to the wireless network. We are using Active Directory for the backend user database and have assigned the users to different groups in AD. We have a Network Admins group to access the network devices and a Wireless Users to access the WLAN. The problem that we have is that everyone in the Wireless Users group can access the devices and run full commands on them. We want to limit the Wireless Users group from being able to do this. Is there a policy or config change that we will need to make for this?
View 3 Replies
View Related
Feb 16, 2013
We recently deployed ACS 5.3 on a VM, while the main purpose of implementation was to control access (authentication/authorization) on network devices; Can we use the same user to authenticate users' access to our wired network? So only users with a valid credentials on our Windows AD can have access to the network?
View 1 Replies
View Related
Jun 30, 2011
Is there much of a network speed difference between a green drive, Seagate Barracuda or a regular drive?i.e. would you see greater network throughput with a 7200 RPM drive compared to a 5900 RPM drive?
View 6 Replies
View Related
Aug 15, 2012
When doing a backup on any of the ACS 5.x appliances by default the backup is encrypted with PGP. What password is used for that? Is it configurable?
View 3 Replies
View Related
Oct 5, 2011
Does the following setting is a shipping default in the ACS 5.1?,In the Access Policies ->Network Device Admin -> Identity -> Advanced Options, the If user not found was set to “Continue” .
View 6 Replies
View Related
Apr 17, 2013
For ACS 5.4: In Network Access -> Authorization Profiles there is a Permit Access profile. If you try to edit it a message pop's up that says: "The profile you have selected is reserved and cannot be deleted or modified". What this profile contains in its rule base? If I wanted to create a similar profile what Common Tasks, or Radius Attributes would I need to use? The same would go for a Deny Access profile. I have looked at the Common Tasks and Radius Attributes for a new profile and it doesn't seem very intuitive.
View 2 Replies
View Related
Mar 23, 2012
How to implement certificate based 802.1x authentication network access using ACS5.3 & external identity store as AD.
View 13 Replies
View Related
Feb 24, 2013
The ADSL Modem CISCO867-K9 is not connecting to our NAS router with default mtu value in the NAS router virtual template
Is there is any reason for ths ? With the below settings my ADSL 867 connecting , but if i remove the (mtu 1440 and ip tcp adjust-mss 1392 , this modem is not connecting
My Virtual Template config
interface Virtual-Template1
mtu 1440
ip unnumbered Loopback3
[Code].....
View 1 Replies
View Related
Jun 6, 2013
I am going to deploy Cisco ISE with WLC 5500. I have two kinds of users one for which I want to deploy just open access Wi-Fi network, without working with Cisco ISE and Second group of Users for which I want to deploy Cisco ISE services like advanced authentication, posture and profiling. For both users I have just one WLC. Is there any problem to just deploy two SSID one for open access (without Cisco ISE) and second Secure with Cisco ISE ?
View 5 Replies
View Related
Dec 26, 2011
I need to know how WLC can support ISE guest management in wireless mode. Tested and confirm by Cisco SE, Knowing that WLC currently does not support dynamic VLAN authorization for central web authentication. This limitation will be addressed in WLC 7.2 when MAB and CWA support is added to the code. On the other hand, DACLs on the other hand works and we can use that to restrict access of this guest traffic.Can ISE support on WLC LWA guest access provision? This able to view guest user login and show at ISE monitoring.
View 1 Replies
View Related
May 1, 2013
I'm trying to configure ACS 5.4 as radius server for network access (PPP connections).In monitoring and reports the users have green color , but the clients cannot send data. Auth method is CHAP/MD5.
Allowed protocols are set to CHAP and PAP only.
View 5 Replies
View Related
Jan 2, 2013
I have a Cisco ASA 5510. I have configured Cisco Anyconnect to authenticate via Windows IAS. We had an outage of that server recently and I tried to remote in via anyconnect and could not. Once the IAS server came up I could get back into the network.
Is there a command that I'm missing that will let me use Anyconnect to connect into the network even if my AAA server is down?
View 2 Replies
View Related
Jan 3, 2012
I have a cisco 870 router which I'm trying to connect to my ISP all the interfaces are in a up, up state. But I'm unable to ping any IP address on the internet. When I do a debug ppp I can see that the username and password are correct with the dialer 1 interface as there is no errors and I can see success. But when I shutdown the atm0 interface and then do a no shutdown I see a message called authentication failed.How does the atm0 interface work with the dialer,Also I spoke to the ISP and they can't see any connection being made but the debug shows success. I also get a default gateway via the ISP but it is the incorrect default gateway as I can't ping the internet and the ISP confirms that the default gateway is incorrect.
View 33 Replies
View Related
Sep 9, 2011
My ISP here at my mother's in Italy (www.teletu.it) gave me the following configuration:
1. Supported Protocol: PPPoE or PPPoA
2. VPI: 8
3. VCI: 35
4. Encapsulation: LLC (If not supported: VCMUX/NULL)
5. Modulation: Multimode
6. Authentication Protocol: PAP or CHAP
if I connect my laptop to the ADSL modem, it all works just fine and I can connect to the internet (as you can see )
HOWEVER, if I then try to configure my WRT54G v6 to use this internet connection (I NEED to be wireless here, or I won't be able to use my iPhone and iPad), there is no way apparently for me to configure the Encapsulation, Modulation, and Authentication Protocol above. I just upgraded my WRT54G's firmware, and am now running firmware Ver.1.02.8, 10/05/2009. I was hoping this would allow me to set these parameters, but I can't find a way.
I tried just configuring the WRT54G with PPPoE and the ISP's userId/password, but this doesn't seem to suffice, and I don't see any other settings I could try.
View 3 Replies
View Related
Feb 6, 2011
I have a problem trying to export logs to the Cisco ACS View from my ACS 4.2In the document [URL] Cisco states that one of the mandatory attributes for export to work is "Network Access Profile Name" under TACACS+ Accounting (under ACS 4.2 System configuration -> Logging settings). Well, I don't have this mandatory attribute listed in ACS under TACACS+ accounting log configuration. I tried to ignore this attribute, but then ACS View complains about null value for the attribute mentioned above.Is this some bug in ACS View or ACS or maybe I simply missing something?
View 1 Replies
View Related
Apr 15, 2013
I have some older devices on the network that only support RADIUS (not TACACS) for authentication and would like to have them use SecureACS 5.3
I understand that by default, ACS only supports TACACS for device administration. So I'll get this error when trying RADIUS:
11033 Selected Service type is not Network Access
Description:
RADIUS requests can only be processed by Access Services that are of type Network Access
Resolution Text: Verify that the Service Selection Policy rules are correct
However, even after adjusting the Service Selection rules and seeing hits, I still see the same message in the logs, as if it has no affect.
View 1 Replies
View Related
Apr 14, 2011
I have ACS 5.2 running as a VM. I'm AD, then local authentication successfully for device access, but I want to define ACS user groups to restrict login. I don;t see any way to do this. If I use AD groups, they don;t show up as selection options on the policy screens, just the ACS locallyy defined groups.
View 1 Replies
View Related
Feb 21, 2013
I have some network devices that are connected to a 110v power source that goes through a 110v/5v power converter.The Access points keep going back to factory default settings and losing their configuration. I have the same access points installed in the same situation but on a different site that work fine.have changed both the configuration and firmware to be be identical to the working Access Points and still the others default.They do not do this at a specific time of day and out of the 6, they do this at random and not at the same time. Sometimes they will go 24 hours + without defaulting, sometimes they'll go just 4 hours.
View 2 Replies
View Related
Jul 11, 2012
I am having connection issues with my laptop involving my wireless adapter (I assume), since I am able to connect to the internet via a different laptop, Xbox and phones in the household. It is a Dell M5010 and the problem has only recently occurred.
View 9 Replies
View Related
Jun 6, 2012
I am trying to set up a PPTP VPN connection which also provides internet access. I have the following configuration. The router named "Router1" connects 2 computers PC1 and PC2 on the LAN side with a network address of 192.168.1.0/24. It is a PPTP server and a DHCP server. It gives IP addresses to PC1 and PC2. It has a static address of 192.169.1.2 on the LAN side and a static address of 10.2.9.1 on the WAN Side. PC3 has a static address of 10.2.9.2 and is connected to the WAN port of Router1. "Router2" is connected to the LAN side of Router1 and it has a static IP of 192.168.1.1. Router2 is connected to the internet and provides internet connection to PC1 and PC2. PC1 and PC2 connects fine to the internet and can see each other. However, PC3 cannot connect to the internet even though it is connected to Router1 by PPTP VPN connection. PC3 can see PC1, PC2, Router1 and Router2 but it cannot connect to the internet because Router1 does not give it the default gateway(192.168.1.1) to connect it. When PC3 connects via PPTP, It receives a correct IP address(10.2.9.3), correct DNS addresses but the ip4 default gateway field is left blank, and the DHCP option is not enabled on connection properties of PC3. Router1 is a DD-WRT firmware router (DLink Dir 400) and has PPTP server enabled as a service. How do I get Router 1 to give PC3 a default gateway IP? And how do I forward all outgoing packets from Router 1 to Router 2? I do not need port forwarding for some ports, I need full access to the internet from PC3 though the PPTP connection via Router2.
View 3 Replies
View Related
Jun 18, 2011
I have a pocket wifi which allows you to connect up to five devices. my mum, sister and my phone can access it no problems but my laptop wont work.what will happen is:
- it connects automatically to the wifi
- but it has a little error mark on it
- and it says theres no internet access.
ive tried everything, ive ran several windows network diagnostics and it says the problem is the default gateway being unavailable.
View 4 Replies
View Related
